Menu Volume + Volume − Preset Alarm Info − Select Source Sleep Menu + Standby Aux in (iPod not included) Owner’s manual CHRONOS iDOCK Printed on 100% recycled paper using soya-based ink
Safety instructions Copyright Trademarks Keep the radio away from heat sources. Do not us e t he r adio near wat er. Avoid objects or liquids getting into the radio. Do not remove screws from or open the radio casing. Fit the mains adaptor to an easily accessible socket located near the radio and ONLY use the mains power adapter supplied. Keep the supplied iPod Dock Adapters away from small children. Copyright 2007 by Imagination Technologies L imited. All r ight s reser ved.
Contents Overview of the controls and connectors ................................2 Icons on the display .................................................................2 Quick set up .............................................................................4 Listening to DAB and FM ..........................................................5 Changing stations................................................................................................... 5 Changing the information shown on screen .....
Overview of the controls and connectors Front Remote Standby Menu Volume + Volume − Preset Alarm Info − Select Source Sleep Menu + Standby Aux in Top x7 Underneath 9V DC Icons on the display iPod APSX^ =^f _[PhX]V) 6[ 2
Key to controls and connectors 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. Set and select preset stations. » Page 6 Cycle through on-screen information. » Page 5 Set and adjust alarms, when the unit is on or in standby. » Page 8 Access setup options » Page 10 In DAB Press +/- to scroll through radio stations. Press Select to listen. » Page 5 In FM Press and release +/- to manually tune up or down frequency range.
Quick set up 1. Pull out the plastic slip from the remote control battery compartment. Magnetic strips (x2) The remote can be magnetically attached to the side of the unit for handy storage. If you’d like to do so, affix one of the supplied adhesive magnetic strips to the recess on the reverse of the remote and one to the side of the unit. 2. Open the box containing the iPod Dock Adapters and select the adapter that is compatible with your model of iPod as detailed in the table below.
Listening to DAB and FM Changing stations DAB 112 APSX^ ! 0 \hbcTah c^da c 112 APSX^ ! 112 A%< 112 APSX^ %
Setting and selecting presets Store up to 30 DAB and FM radio stations in a combined list for quick access to your favourite stations. To set a preset Tune to the station you want to store. Press the Preset button and use the +/- buttons to select the Preset number you wish to save the station to. Hold down the Select button or the Preset button for 3 seconds until the display changes to a confirmation message, e.g., ‘Preset 1 saved’.
2. Press the Source button and repeat to change the audio source to ‘iPod’. Alternatively, press the Play/Pause button on the mini-remote, which will wake your iPod and start playing a track, even if you’re listening in DAB, FM or Auxiliary mode. Menu iPod iPod ;W]ZKM or Volume + Volume − Preset Alarm Info − Select Source Sleep Menu + Standby Aux in 3. Select and play a track using your iPod or the mini-remote. 4.
Setting alarms Chronos iDock has 4 alarms. When activated, an alarm either switches the radio on (if in standby) and tunes to a DAB or FM radio station; activates and plays your iPod (if docked); or sounds a beeping alarm tone. How to set an alarm 1. Press the Alarm button then select Alarm 1, 2, 3 or 4 with +/− and Select. The time, repeat days and on/off status are displayed on the top line. )TIZU 2. Tip >UU >] ;MTMK\ An alarm you’ve already set can be turned off by selecting ‘Set Alarm > Off’.
7. Select ‘Set volume’ and adjust the volume level for the alarm from 1 (very quiet) to 16 (very loud) using the +/− buttons and Select to confirm. That’s it! You can see which alarms are currently switched on by looking at the numbered alarm clock icons on the screen, in either active or standby mode.
Using the sleep timer The sleep timer switches your radio into standby after a number of minutes. To set/change the sleep timer Press the Sleep button and repeat to increase the duration of the Sleep timer (90 minutes maximum). Wait a few seconds and the Sleep timer will activate. ;TMMX BTc b[TT_ $ \X]b ;TMMX BTc b[TT_ " \X]b To cancel the sleep timer Press and hold the Sleep button for 3 seconds.
Other options Display Press the Menu button and select ‘Display’. You can customise the display settings for both Active and Standby modes. The diagram below shows the available options. Display Active mode Contrast Standby mode < 1 - 16 > Brightness < 1 - 9 > Timed Always on Timed Active mode: Standby mode: Timed: Always on: Auto dimming: Brightness: Contrast: Always on Auto dimming Backlight settings that apply when the unit is switched on.
Audio Set the Treble and Bass levels. Manual tune Shows DAB signal level, which can help you find the best position for your radio. 1. Use the +/- buttons to scroll through different channels and push Select to choose one (UK stations are in the range 11B to 12D). You see a signal level display. The empty block indicates the minimum required level for reception and the filled blocks indicate the current level. 2. Move your aerial/unit and to try to raise the current level to the empty block or beyond.
The bass/treble on iPod tracks is too high Check the bass and treble controls on the iPod, which will affect the sound from the Chronos iDock when playing iPod tracks. The volume control on the iPod does not affect the volume level When your iPod is docked, the volume level must be adjusted on the unit, not the iPod. Do not turn up the iPod volume: it should be left at the volume level you normally use for portable listening.
Warranty information Disclaimer Imagination Technologies Ltd. warrants to the end user that this product will be free from defects in materials and workmanship in the course of normal use for a period of two years from the date of purchase. This guarantee covers breakdowns due to manufacturing or design faults; it does not apply in cases such as accidental damage, however caused, wear and tear, negligence, adjustment, modification or repair not authorised by us.
www.pure.com PURE Digital Imagination Technologies Ltd. Home Park Estate Kings Langley Herts, WD4 8DH UK +44 (0)1923 277477 support +44 (0)1923 277488 sales PURE Digital Karl-Marx Strasse 6 64589 Stockstadt/Rhein GERMANY +49 (0)6158 878872 sales PURE Digital - Vertrieb über: TELANOR AG Unterhaltungselektronik Bachstrasse 42 4654 Lostorf SCHWEIZ/SWITZERLAND +41 (0)62 285 95 95 sales EcoPlus 100% +44 (0)1923 270188 support@pure.com sales@pure.com +49 (0)6158 878874 sales_gmbh@pure.