3480 Drummond Runner OWNER’S MANUAL FISHING BOATS 3901 St. Lucie Blvd. Ft.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 2 3480 DRUMMOND RUNNER
SAFETY INFORMATION Your Owner’s Manual has been written to include a number of safety instructions to assure the safe operation and maintenance of your boat. These instructions are in the form of DANGER, WARNING, CAUTION, and NOTICE statements. The following definitions apply: IMMEDIATE HAZARDS WHICH WILL RESULT IN SEVERE PERSONAL INJURY OR DEATH. HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN SEVERE PERSONAL INJURY OR DEATH.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 4 3480 DRUMMOND RUNNER
BOAT INFORMATION Please fill out the following information section and leave it in your Pursuit Owner’s Manual. This information will be important for you and Pursuit service personnel to know, if and when you may need to call Pursuit for technical assistance or service.
Operator Notes 6 3480 DRUMMOND RUNNER
CERTIFICATIONS & SPECIFICATIONS (For Export Only) To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information.
Operator Notes 8 3480 DRUMMOND RUNNER
IMPORTANT INFORMATION Warranty and Warranty Registration Cards The Pursuit Limited Warranty Statement is included with your boat. It has been written to be clearly stated and easily understood. If you have any questions after reading the warranty, please contact Pursuit Customer Relations. Pursuit, engine manufacturers, and the suppliers of major components maintain their own manufacturer's warranty and service facilities.
Operator Notes 10 3480 DRUMMOND RUNNER
OWNER'S/OPERATOR'S RESPONSIBILITIES Registration and Numbering Federal law requires that all undocumented vessels equipped with propulsion machinery be registered in the state of principal use. A certificate of number will be issued upon registering the boat. These numbers must be displayed on your boat. The owner/operator of a boat must carry a valid certificate of number whenever the boat is in use. When moved to a new state of principal use, the certificate is valid for 60 days.
USCG specifications and regulations relating to performance, construction, or materials. The equipment requirements vary according to the length, type of boat, and the propulsion system. Some of the Coast Guard equipment is described in the Safety Equipment chapter of this manual. For a more detailed description, obtain “Federal Requirements And Safety Tips For Recreational Boats” by contacting the Boating Safety Hotline 800-368-5647 or your local marine dealer or retailer.
TABLE OF CONTENTS Introduction: Safety Information ..................................................................................... 3 Boat Information ........................................................................................ 5 Certifications & Specifications .................................................................. 7 Warranty Information ................................................................................ Tab Important Information.....................................
Chapter 4: Electrical System 4.1 4.2 4.3 4.4 4.5 4.6 4.7 General ............................................................................................ 33 12-Volt DC System .......................................................................... 33 DC Distribution System ................................................................... 33 12-Volt DC Panels ........................................................................... 35 AC Systems ....................................................
Chapter 8: Interior Equipment 8.1 8.2 8.3 8.4 8.5 8.6 Companionway Door ...................................................................... 63 Head Compartment ......................................................................... 63 V-Berth ........................................................................................... 64 Carbon Monoxide Detector ............................................................ 65 Air Conditioner ...............................................................
Chapter 11: Routine Maintenance 11.1 11.2 11.3 11.4 11.5 11.6 General ........................................................................................... 93 Exterior Hull and Deck .................................................................. 93 Upholstery, Canvas and Enclosures ................................................ 97 Cabin Interior ................................................................................. 98 Bilge .............................................................
Chapter 1: PROPULSION SYSTEM 1.1 General The Pursuit 3480 Drummond Runner is designed to be powered with twin 2-cycle or 4-cycle outboard motors. Each manufacturer of the various outboard motors provides an owner’s information manual which includes its limited warranty statement with its product. It is important that you read this information very carefully and become familiar with the warranty and proper care and operation of the engine and drive system.
DO NOT PAINT THE OUTBOARD MOTORS WITH ANTIFOULING PAINTS DESIGNED FOR BOAT HULLS. MANY OF THESE PAINTS CAN CAUSE SEVERE DAMAGE TO THE ENGINES. CONTACT YOUR PURSUIT DEALER OR ENGINE MANUFACTURER FOR INFORMATION ON THE PROPER PAINTING PROCEDURES. 1.3 Engine Lubrication 4-cycle outboard engines have an oil sump in the crankcase that must be kept full of the type and grade of oil recommended by the engine manufacturer. It is normal for 4-cycle engines to consume a small amount of oil.
1.5 Propellers The propellers convert the engine’s power into thrust. They come in a variety of styles, diameters and pitches. The one that will best suit the needs of your Pursuit will depend somewhat on your application and expected average load. Propeller sizes are identified by two numbers stamped on the prop in sequence. The 1st number in the sequence (example 14 x 21) is the diameter of the propeller, and the 2nd number is the pitch.
FUEL GAUGE The fuel gauge indicates the amount of fuel in the fuel tanks. The engine instrumentation has a feature that allows the fuel gauge to read the level of either fuel tank. Refer to the Yamaha® owner's manual for information on using this feature. This gauge is a relative indication of the available fuel supply and not a calibrated instrument. VOLTMETER The voltmeter displays the voltage for the battery and the charging system.
Chapter 2: HELM SYSTEMS 2.1 General The helm controls consist of three systems: the engine throttle and shift controls, the steering system and the trim tab control switches. Each manufacturer of the control components provides an owner’s manual with its product. It is important that you read the manuals and become familiar with the proper care and operation of the control systems. 2.2 Engine Throttle and Shift Controls The shift and throttle controls on your boat may vary depending on the engines used.
start position just long enough to briefly engage the starter for the engine. Do not hold the key in the start position long enough to start the engine. The starter should not engage for either engine. Repeat this test with the shift levers in reverse and the engine throttles at idle. Again, the starter should not engage for either engine.
2.6 Engine Stop Switch WE STRONGLY RECOMMEND THAT THE LANYARD BE ATTACHED TO THE DRIVER WHENEVER THE ENGINES ARE RUNNING. Your Pursuit is equipped with an engine stop switch and lanyard. When the lanyard is pulled it will engage the switch and shut off the engines. If the engines will not start, it could be because the lanyard is not properly inserted into the engine stop switch. Always make sure the lanyard is properly attached to the engine stop switch before attempting to start the engine.
DO NOT ATTEMPT TO ADJUST THE HELM WHEEL POSITION WHILE UNDERWAY. 2.8 Trim Tabs The trim tabs are recessed into the hull under the transom area. Switches are used to control the trim tabs. The switches are labeled and control bow up and down movements. It also controls starboard and port up and down movements. Bow up and bow down will control the hull planing attitude, while port and starboard up and down provide control for the hull trim side to side.
2.10 Control Systems Maintenance CONTROL MAINTENANCE Periodic inspection of the control systems and all connections should be made. Signs of rust, corrosion, wear, or other deterioration should immediately be serviced. Generally, periodic lubrication of all moving parts and connections with a light waterproof grease is in order. Control system adjustments may become necessary. If adjustments become necessary, see your Pursuit dealer. INSPECT AND MAINTAIN THE STEERING SYSTEM REGULARLY.
Operator Notes 26 3480 DRUMMOND RUNNER
Chapter 3: FUEL SYSTEM 3.1 General The fuel system used in Pursuit boats is designed to meet the requirements of the U.S. Coast Guard, the National Marine Manufacturers Association (NMMA), and The American Boat and Yacht Council (ABYC) in effect at the time of manufacture. Fuel systems have been factory inspected and pressure tested in accordance with regulations in effect at the time of manufacture. This inspection assures that the system is air tight, leak proof and safe.
DO NOT CONFUSE FUEL FILL DECK PLATES WITH THE WATER OR WASTE FILL DECK PLATES. THESE PLATES ARE ALSO LABELED ACCORDINGLY. IF GASOLINE OR DIESEL IS ACCIDENTALLY PUMPED INTO THE WATER OR WASTE TANK, DO NOT ATTEMPT TO PUMP IT OUT YOURSELF. WATER AND WASTE PUMPS ARE NOT DESIGNED TO PUMP FUEL AND FIRE OR EXPLOSION COULD RESULT. HAVE THE FUEL PROFESSIONALLY REMOVED AND THE COMPONENTS OF THE FRESH WATER SYSTEM REPLACED AS NECESSARY.
GASOLINE FUEL FILTER Fuel filters are located under the aft seat and accessed through a hatch. Fuel primers are built into the top of each fuel filter. Primer bulbs are not used in the fuel lines. The filters are the water separator type and there is one filter for each engine fuel line. Each fuel filter has a sediment bowl that should be checked for water frequently to assure an adequate supply of clean, dry fuel to the engines.
To fill the fuel tank at a marina, follow this procedure: 1. Make sure all switches are in the “Off” position. 2. Make sure the boat is securely moored. 3. Make sure all passengers leave the boat. 4. A special key to open the fuel caps is supplied. 5. Turn the key counterclockwise to open the cap. 6. Remove the cap. 7. Put the nozzle in the fuel opening. STATIC ELECTRICITY CAN BE GENERATED WHILE FUELING AND CAN CAUSE A FIRE OR EXPLOSION.
3.5 Fuel System Maintenance PERIODICALLY INSPECT ALL PRIMER BULBS, CONNECTIONS, CLAMPS AND HOSES FOR LEAKAGE AND DAMAGE OR DETERIORATION. REPLACE AS NECESSARY. Spray the valves, tank fuel gauge sender and ground connections with a metal protector. Frequently inspect and lubricate the fuel fill cap O-ring seals with petroleum jelly or silicone grease.
Operator Notes 32 3480 DRUMMOND RUNNER
Chapter 4: ELECTRICAL SYSTEM 4.1 General Your Pursuit is equipped with AC and 12-volt DC electrical systems. The AC system can draw current from one of two sources, either shore power outlets at dockside or the optional generator. The DC system draws current from on-board batteries. The Group 31, 12-volt batteries provided in your boat are of the lead-acid type. They will require periodic maintenance. Two batteries are located in the aft cockpit machinery space.
Parallel Switch: Connects the batteries together for engine starting or charging of all batteries. Voltage Sensitive Relay (VSR): The VSR (on rear of the panel) allows two batteries to be charged either by one engine or by the on-board battery charger. The VSR prevents both batteries from being discharged by automatically isolating the engine battery. Helm Main Supplies 12-volt electrical current to the breakers on the helm breaker panel.
BATTERY SWITCHES There are three battery switches and two parallel switches to manage the 12-volt power distribution. The Port Start switch controls the battery for the port engine. The Starboard Start switch controls the battery for the starboard engine. Parallel switches connect the port and starboard engine batteries and the house battery for emergency starting if one of the engine batteries is dead or low. The "winch" switch provides power to the windlass.
Aft Stbd Bilge Activates the aft starboard bilge pump. Hardtop Lights Activating this button activates the lights mounted underneath the hardtop. Spreader Lights Activates the flood lights located on the hardtop. These lights provide additional lighting for the rear of the cockpit. Windlass Activates the windlass. See the Exterior Chapter for proper use of the windlass. Fishbox Pump Activates the fishbox macerator. Port Vent This switch operates the port windshield vent window.
Island Lights Activates the lights mounted under the hardtop to illuminate the island surface. Island Accent Lights Activates the accent lights located along the bottom perimeter of the cockpit island. Cockpit Lights Activates the lights that illuminate the cockpit area. Additional switches are located in the cockpit of the boat. The following are descriptions of these functions: Electric Seats Switches are mounted on the helm to operate the electric helm and companion seats.
CARBON MONOXIDE IS A LETHAL, TOXIC GAS THAT IS COLORLESS AND ODORLESS. IT IS A DANGEROUS GAS THAT WILL CAUSE DEATH IN CERTAIN LEVELS. The following circuits are protected by switchable circuit breakers. Should any of these breakers trip, the breaker can be reset by turning the breaker off and then back on. Electric Head This breaker provides circuit protection to the VacuFlush system that operates the head.
4.5 AC System The AC system is fed by the shore power outlet or by the optional generator. It is wired totally separate from the 12-volt DC system and is equipped with an on-board galvanic isolation system. The galvanic isolator, located behind the electrical panel, is equipped with a system status monitor. Refer to the galvanic isolator owner's manual. A shore power inlet breaker is located in the aft cockpit adjacent to the aft seat.
DO NOT ATTEMPT TO CORRECT THE WIRING YOURSELF. ELECTRIC SHOCK CAN CAUSE SEVERE INJURY OR EVEN DEATH. ALWAYS HAVE A QUALIFIED ELECTRICIAN CHECK WIRING. KEEP CHILDREN AWAY FROM ANY ELECTRICAL CABLES OR EQUIPMENT AND ALWAYS USE GROUNDED APPLIANCES ON BOARD YOUR BOAT. DO NOT OPERATE THE AC ELECTRICAL SYSTEM FROM SHORE POWER WITH REVERSE POLARITY. REVERSE POLARITY WILL DAMAGE THE SYSTEM AND EXPOSE PASSENGERS TO ELECTROCUTION HAZARDS. THIS CONDITION COULD ALSO CAUSE A FIRE IN THE ELECTRICAL SYSTEM.
Reverse Polarity Light Test Switch There is a momentary switch located below the reverse polarity light in the AC breaker panel. This switch is used to test the reverse polarity light to ensure that it is functioning. The light can be tested by depressing the switch whenever the AC system is activated. The reverse polarity light should be tested each time the AC system is activated.
4.6 Generator (Optional) Your Pursuit may be equipped with an optional generator. An owner operator's manual for the generator has been supplied with this manual. Please refer to it for details on the generator operation. The generator compartment located in the aft cockpit machinery space is equipped with a blower for ventilation. Please refer to the Ventilation System chapter. The generator compartment is equipped with an automatic fire extinguisher system and an automatic engine shutdown system.
lubricant like petroleum jelly or silicone grease. The sockets should be sprayed with a protector. Care must be taken not to get any oil or petroleum jelly on the glass portion of the bulbs as this will cause the bulb to overheat and burn out. WHEN REPLACING LIGHT BULBS IN MARINE LIGHT FIXTURES, ALWAYS USE A BULB WITH THE SAME RATING AS THE ORIGINAL. USING A DIFFERENT BULB COULD CAUSE THE FIXTURE TO OVERHEAT AND MELT OR SHORT CIRCUIT.
important factors to the generator's longevity are proper ventilation, maintenance of the fuel system, ignition system, cooling system, lubrication system and the AC alternator. Maintenance schedules and procedures are outlined in your generator owner’s manual. They should be followed exactly. CORROSION ALLOWED TO BUILD ON THE ELECTRICAL CONNECTORS CAN CAUSE A POOR CONNECTION RESULTING IN SHORTS, GROUND FAULTS OR POOR GROUND CONNECTIONS.
Chapter 5: PLUMBING SYSTEMS 5.1 Fresh Water System GENERAL The fresh water system consists of a potable water tank, distribution lines and a distribution pump. The pump is equipped with an automatic pressure switch and is accessed through the aft most cockpit hatch. An in-line strainer located near the pump protects the system from debris. The tank is filled through a labeled deck plate located on the gunwale. DO NOT FILL THE SYSTEM WITH ANYTHING OTHER THAN WATER.
WATER HEATER The water heater is located in the cockpit island behind the port side storage cabinet. All heaters have an AC element that is thermostatically controlled at the heater and activated by a circuit breaker located in the AC panel. A high pressure relief valve protects the system from excessive pressure. Always make sure all air is purged from the water heater and lines before activating the water heater breaker. Refer to the water heater owner’s manual for additional information.
OPERATION A high pressure pump, controlled by a pressure sensor, supplies the raw water hose connector located in the cockpit. The pump is activated by the washdown breaker on the cabin DC breaker panel. The breaker should be kept off when the washdown is not in use. When activated, the pressure switch will automatically control the pump. As the pressure builds in the washdown hose, the pump will shut off. When the washdown hose is in use and the pressure drops, the pump will turn on.
The pump, the strainer and seacock are located in the cockpit machinery space. Please refer to the air conditioner owner's manual for more information on the operation and maintenance of the air conditioner. 5.4 Drainage GENERAL All water is drained by gravity to overboard thru-hull fittings located in the hull sides above the waterline. Some of the drain thru-hull fittings are equipped with ball valves that are always open under normal operating conditions.
A LOOSE DRAIN PLUG WILL ALLOW SEA WATER TO ENTER THE BILGE AND COULD CAUSE THE BOAT TO SINK. IT IS VERY IMPORTANT TO CHECK THE DRAIN PLUG FREQUENTLY TO ENSURE IT IS PROPERLY TIGHTENED.
5.5 Plumbing Systems Maintenance WATER SYSTEMS Information supplied with water system components, by the equipment manufacturers, is included with this manual. Refer to this information for additional operation and service data. The following items should be done routinely to maintain your fresh water system: • Remove the filter screens from the faucet spouts and eliminate any accumulation of debris. A build-up of debris can cause the pump to cycle excessively.
THE FRESH AND RAW WATER SYSTEMS MUST BE PROPERLY WINTERIZED PRIOR TO WINTER LAY-UP. SEE THE SECTION ON WINTERIZING. DRAINAGE SYSTEMS It is essential that the following items be done periodically to maintain proper drainage of your boat: • Clean the cockpit drain rails with a hose to remove debris that can block water drainage. • Clean the hardtop leg drain holes. This is especially important just before winter layup.
Operator Notes 52 3480 DRUMMOND RUNNER
Chapter 6: VENTILATION SYSTEM 6.1 Cabin Ventilation Ventilation to the cabin area and head is provided by deck hatches. DECK HATCH The deck hatch is supported in the open position by an adjustable hatch adjuster. To close the hatch, loosen the hatch adjuster and lower the hatch. Secure in the closed position with the two cam levers on the inside of the hatch. The dogs that secure the hatch have spacers that can be removed to increase the tension provided by the dogs. OPEN FLAMES DEMAND CONSTANT ATTENTION.
boards. This provides adequate air movement in the bilge and generator compartments. 6.5 Generator Compartment Ventilation Your Pursuit may be equipped with the optional generator which by regulation mandates that the cockpit machinery space be considered as an engine compartment. The ventilation system is designed to meet the requirements of the United States Coast Guard in effect at the time of manufacture.
• Blower operation can and should be tested by placing a hand over the exhaust vent. Do not rely on the sound of the blower. A substantial amount of air should be exhausted by the blower. Frequently check the intake vent for obstructions, preferably before each cruise. • Many manufacturers of carbon monoxide detectors offer a testing and recertification program. We recommend that you contact the manufacturer of your carbon monoxide detector and have it tested and recertified periodically.
Operator Notes 56 3480 DRUMMOND RUNNER
Chapter 7: EXTERIOR EQUIPMENT 7.1 Deck RAILS AND DECK HARDWARE The rail system and hardware fittings have been selected and installed to perform specific functions. Fenders or mooring lines should be secured to the cleats and not to rails or stanchions. Be sure a clear lead exists when running dock lines or anchor lines. A line inadvertently run around a stanchion or over the rail could cause damage. The aft mooring cleats are flush mount and must be raised prior to use.
The windlass locker is drained by a thru-hull fitting. Check the drain frequently to make sure it is clean and free flowing. THE ANCHOR MUST BE POSITIONED SO IT DOES NOT REST AGAINST THE HULL SIDES AND BE PROPERLY SECURED AT ALL TIMES. The anchor is secured in an anchor chute that extends through the stem of the boat. The anchor line is stored in the rope locker and routed out through the windlass to the anchor chain.
7.2 Hull SWIM PLATFORM Your Pursuit is equipped with an integral swim platform and engine mounting system located in the stern of the boat. There are inspection deck plates in the splashwell to provide access to the stern bilge and engine mounting bolts. Always make sure these plates are secure before operating your boat. BOARDING LADDER A fold-away boarding ladder is located under the hatch on the swim platform. MOVING PROPELLERS ARE DANGEROUS. THEY CAN CAUSE DEATH, LOSS OF LIMBS OR OTHER SEVERE INJURY.
The refrigerator in the cockpit island runs on DC power only. Care should be exercised while operating the refrigerator on 12-volt power without the engines running. It draws a substantial amount of current and can severely drain a battery through extended use. When at dockside ensure that the battery charger is on. If the boat is equipped with the optional generator, when underway or at anchor, run the generator and turn on the battery charger to maintain the house battery.
COCKPIT SHOWER A fresh water shower is located behind a small door in the cockpit. It is supplied hot and cold water by the fresh water system and works much like the shower in the head. HARD TOP The hard top consists of a laminated fiberglass top mounted to a welded aluminum frame that is bolted to the deck. It is designed to accommodate radio antennas, radar antennas and navigation lights. It could also be equipped with optional outriggers and/or rod holders.
NOTICE TO PREVENT GEL CRACKING OR DAMAGE TO GUNWALES OR DECKS, SUPPORT EXTENDING TO THE STRINGERS MAY BE REQUIRED. FIBERGLASS DAMAGE DUE TO THE AFTERMATH INSTALLATION OF A TOWER IS NOT COVERED BY THE PURSUIT LIMITED WARRANTY. EQUIPPING A BOAT WITH A TOWER MAY REQUIRE INSTALLATION OF LOWER PITCH PROPS TO COMPENSATE FOR THE WIND RESISTANCE AND WEIGHT OF THE TOWER.
Chapter 8: INTERIOR EQUIPMENT 8.1 Companionway Door The cabin is accessed through a sliding hatch and hinged door. The hatch is secured to the cabin door with a latch at the top of the door that must be released before opening the companionway door. A locking latch secures the door in the closed position. There is a latch on the bulkhead next to the door to secure it in the open position. It is very important that the cabin door is secured properly in the open or closed position.
in vacuum in the system, it automatically signals the pump to energize and bring the vacuum back to operating level. This process is normally completed in less than two minutes. It is normal for the stored vacuum to leak down slightly between flushes, causing the vacuum pump to run for a short period. The pump should not run more than once every three hours after the last flush for recharging the system. A holding tank fluid level monitor and macerator pump-out switch is located in a panel near the toilet.
8.4 Carbon Monoxide Detector The Safety Equipment chapter in this manual contains important information on carbon monoxide and the carbon monoxide detector. Read the section entitled "Carbon Monoxide" in the Safety Equipment chapter of this Owner's Manual. 8.5 Air Conditioner (Optional) The air conditioning unit is the reverse cycle type and operates on AC power. It is located under the V-berth. The unit is equipped with reverse cycle heat and can be operated as a cooling or heating unit.
TV A flat screen TV is provided as standard equipment. Please refer to the TV owner's manual. DVD The DVD is mounted to the right of the stereo above the AC and DC panels. Please refer to the DVD owner's manual. TV ANTENNA A TV antenna is installed on the hard top. An A/B switch is used to switch the TV between the antenna and the dockside cable. The A/B switch is mounted in the cabinet with the electrical panels. A red light on the antenna indicates that the antenna is selected and activated.
Chapter 9: SAFETY EQUIPMENT 9.1 General Your boat and outboard engines have been equipped with safety equipment designed to enhance the safe operation of the boat and to meet U.S. Coast Guard safety standards. The Coast Guard or state, county, and municipal law enforcement agencies require certain additional accessory safety equipment on each boat. This equipment varies according to length and type of boat and type of propulsion.
9.3 Neutral Safety Switch Every control system has a neutral safety switch incorporated into it. This device prohibits the engines from being started while the shift lever is in any position other than the neutral position. If the engines will not start, slight movement of the shift levers may be necessary to locate the neutral position and disengage the safety cutout switch. Control or cable adjustments may be required to correct this condition should it persist.
IF ACTIVATION SHOULD OCCUR, IMMEDIATELY SHUT DOWN ALL ENGINES. TURN OFF ALL ELECTRICAL SYSTEMS, POWERED VENTILATION AND EXTINGUISH ALL SMOKING MATERIALS. DO NOT OPEN THE ENGINE COMPARTMENT HATCH IMMEDIATELY!! THIS FEEDS OXYGEN TO THE FIRE AND A FLASHBACK COULD RESULT. ALLOW THE EXTINGUISHING AGENT TO SOAK THE GENERATOR COMPARTMENT FOR AT LEAST 15 MINUTES AND WAIT FOR HOT METALS OR FUELS TO COOL BEFORE CAUTIOUSLY INSPECTING FOR CAUSE OR DAMAGE.
Always make sure the battery switch is “on” and the power light on the carbon monoxide detector is lit whenever the cabin is occupied. While a CO detector enhances your protection from CO poisoning, it does not guarantee it will not occur. Do not use the carbon monoxide detector as a replacement for ordinary precautions or periodic inspections of equipment. Never rely on alarm systems to save your life, common sense is still prudent and necessary.
In certain situations, boats can have a problem due to the “station wagon effect” where engine exhaust fumes are captured in the vessel by the vacuum or low pressure area, usually the cockpit, bridge deck and cabin, that can be created by the forward speed of the boat. Boats that are underway should close all aft facing portholes, hatches and doors. The forward facing deck hatches should be open whenever possible to help pressurize the living spaces of the boat.
Your boat should also be equipped with at least a simple marine first-aid kit and a first-aid manual. The marine first-aid kit should be designed for the marine environment and be well supplied. It should be accessible and each person on board should be aware of its location. As supplies are used, replace them promptly. Some common drugs and antiseptics may lose their strength or become unstable as they age.
• Pyrotechnic red flares, hand held or aerial. • Pyrotechnic orange smoke, hand-held or floating. • Launchers for aerial red meteors or parachute flares. PYROTECHNICS ARE UNIVERSALLY RECOGNIZED AS EXCELLENT DISTRESS SIGNALS. HOWEVER, THERE IS POTENTIAL FOR INJURY AND PROPERTY DAMAGE IF NOT PROPERLY HANDLED. THESE DEVICES PRODUCE A VERY HOT FLAME AND THE RESIDUE CAN CAUSE BURNS AND IGNITE FLAMMABLE MATERIAL.
• There is no obvious physical damage, corrosion, leakage or clogged nozzles. Refer to the “Federal Requirements And Safety Tips For Recreational Boats” pamphlet or contact the U.S. Coast Guard Boating Safety Hotline, 1-800-368-5647, for information on the type and size fire extinguisher required for your boat. Please refer to the information provided by the fire extinguisher manufacturer for instructions on the proper maintenance and use of your fire extinguisher.
Additional Equipment to Consider: VHF Radio Heaving Line Flashlight and Batteries Sunburn Lotion Whistle or Horn Boat Hook Food and Water Marine Hardware Life Raft Fenders Mirror Tool Kit Anchor Spare Propellers Binoculars Extra Clothing Spare Anchor First Aid Kit Searchlight Ring Buoy Chart and Compass Mooring Lines Sunglasses Spare Parts 3480 DRUMMOND RUNNER Spare Keys Portable Radio 75
Operator Notes 76 3480 DRUMMOND RUNNER
Chapter 10: OPERATION 10.1 General Before you start the engines on your Pursuit, you should have become familiar with the various component systems and their operation, and have performed a “Pre-Cruise System Check." A thorough understanding of the component systems and their operation is essential to the proper operation of the boat. This manual and the associated manufacturers’ information is provided to enhance your knowledge of your boat. Please read them carefully.
DECKS ARE SLIPPERY WHEN WET. WEAR PROPER FOOTWEAR AND USE EXTREME CAUTION ON WET SURFACES. 10.2 Rules of the Road As in driving an automobile, there are a few rules you must know for safe boating operation. The following information describes the basic navigation rules and action to be taken by vessels in a crossing, meeting or overtaking situation while operating in inland waters. These are basic examples and not intended to teach all the rules of navigation.
OVERTAKING SITUATIONS When one motor boat is overtaking another motor boat, the boat that is being passed has the right of way. The overtaking boat must make the adjustments necessary to provide clearance for a safe passage of the other vessel. The boats should sound the appropriate signals.
THERE MUST BE AT LEAST ONE PERSONAL FLOTATION DEVICE ON BOARD FOR EVERY PERSON ON BOARD AND ONE THROW-OUT FLOTATION DEVICE. CHECK THE U.S. COAST GUARD STANDARDS FOR THE CORRECT TYPE OF DEVICE FOR YOUR BOAT. • Make sure you have signal kits and flare guns aboard, and they are current and in good operating condition. • Be sure you have sufficient water and other provisions for the planned cruise. • Leave a written message listing details of your planned cruise with a close friend ashore (Float Plan).
• Be sure the emergency stop lanyard is attached to the operator and the stop switch. VAPORIZING LIQUID EXTINGUISHERS GIVE OFF TOXIC FUMES; USE ONLY COAST GUARD APPROVED FIRE EXTINGUISHERS. 10.4 Operating Your Boat THE OPERATOR MUST BE SEATED, FACING FORWARD WITH HANDS ON THE CONTROL WHEN THE ENGINE IS RUNNING. AFTER STARTING THE ENGINES: • Check the engine gauges. Make sure they are reading normally. • Visibly check the engines to be sure there are no apparent water, fuel or oil leaks.
• Avoid sea conditions that are beyond the skill and experience of you and your crew. MAKE SURE ONE OTHER PERSON ON THE BOAT IS INSTRUCTED IN THE OPERATION OF THE BOAT AND MAKE SURE THE BOAT IS OPERATED IN COMPLIANCE WITH ALL STATE AND LOCAL LAWS GOVERNING THE USE OF A BOAT. DO NOT OPERATE THE BOAT UNLESS IT IS COMPLETELY ASSEMBLED. KEEP ALL FASTENERS TIGHT. KEEP ADJUSTMENTS ACCORDING TO SPECIFICATIONS. • Before operating the boat for the first time, read the engine break-in procedures.
• Check the bilge area for debris and excess water. • Fill the fuel tanks to near full to reduce condensation. Allow enough room in the tanks for the fuel to expand without being forced out through the vent. • Turn off all electrical equipment except the automatic bilge pumps. • If you are going to leave the boat for a long period of time, put the battery main switches in the “Off” position and close all seacocks. • Make sure the boat is securely moored.
• Be careful when using the trim tabs from the tower. The reaction of the trim tabs will be exaggerated in the tower. Use small tab corrections and wait ten (10) seconds for the tabs to react. Keep making small corrections until the hull is at the desired attitude. • Do not overload the tower. Most towers are designed to hold the weight of only two average sized people. Weight in the tower raises the boat’s center of gravity. Too much weight in the tower could make the boat unstable.
Dock lines are generally twisted or braided nylon. Nylon is strong and stretches to absorb shock. It also has a long life and is soft and easy on the hands. The line's size will vary with the size of the boat. Typically a 30 to 40 foot boat will use 5/8-inch line and a 20 to 30 foot boat will use 1/2-inch line. The number of lines and their configuration will vary depending on the dock, the range of the tide, and many other factors.
LEAVING A MOORING Start the engines and let them warm up for several minutes before releasing the mooring line. The boat will already be headed into the wind, so move it forward enough to loosen the line and untie it. Back the boat away from the mooring until you can see the buoy. Move the boat slowly away from the mooring. ANCHORING Make sure the bitter end of the anchor rode is attached to the boat before dropping the anchor. Bring the bow into the wind or current and put the engine in neutral.
stabilized, thoroughly inspect the boat for damage. Check below decks for leaks and the control systems for proper operation. Plug all leaks or make the necessary repairs to the control systems before proceeding slowly and carefully to port. Request assistance if necessary. Haul the boat and make a thorough inspection of the hull and running gear for damage. 10.
If the boat becomes swamped and capsizes, you and your passengers should stay with the boat as long as you can. It is much easier for the Coast Guard, aircraft, or other boats to spot, than people in the water. 10.12 Transporting Your Boat The Pursuit 3480 Drummond Runner is a large boat and should only be trailered by professionals that have the knowledge and equipment to move large boats without causing damage.
• Make sure the trailer bunks and rollers properly support the hull and do not put pressure on the lifting strakes. The rollers and bunks must be kept in good condition to prevent scratching and gouging of the hull. • The capacity rating of the trailer should be greater than the combined weight of the boat, motor, and equipment. The gross vehicle weight rating must be shown on the trailer. Make sure the weight of the boat, engine, gear and trailer is not more than the gross vehicle weight rating.
10.14 Water Skiing Your Pursuit could be equipped for water skiing. If you have never driven skiers before, you should spend some hours as an observer and learn from an experienced driver. If you are an experienced driver, you should take some time to become familiar with the boat and the way it handles before pulling a skier. The driver should also know the skier’s ability and drive accordingly. The following safety precautions should be observed while towing water skiers.
• Keep the person on the driver side of the boat so you can keep him in sight at all times. • Make sure to approach the person from the downwind side and maneuver the boat so the propellers are well clear of the person in the water. • Turn off the engines when the person is alongside and use a ring buoy or a boat cushion with a line attached, a paddle or boathook to assist him to the boat. Make sure you don't hit him with the ring buoy or the boat.
Operator Notes 92 3480 DRUMMOND RUNNER
Chapter 11: ROUTINE MAINTENANCE 11.1 General BEFORE USING A CLEANING PRODUCT, REFER TO THE PRODUCT DIRECTIONS AND SPECIFICATIONS. NOTICE IF URETHANE FOAM IS USED IN THE CONSTRUCTION OF YOUR BOAT, USE SPECIAL CARE WITH HIGH TEMPERATURES OR FLAMES IN THESE AREAS. URETHANE FOAM CAN IGNITE. REFRAIN FROM BURNING, WELDING, SMOKING, THE USE OF SPACE HEATERS AND LIGHTS IN AREAS WHERE URETHANE FOAM IS PRESENT.
Do not allow the hull antifouling paint to contact the outboard motor. Most antifouling paints designed for hull bottoms contain copper and can cause severe galvanic damage to the motor. Always leave a 1/2" barrier between the hull bottom paint and outboard motor. Most bottom paints require some maintenance. Proper maintenance is especially important when the boat is in saltwater and not used for extended periods or after dry storage.
USE EXTREME CARE WHEN WALKING ON WET GELCOAT SURFACES AS THEY ARE SLIPPERY. STAINLESS STEEL HARDWARE When using the boat in saltwater, the hardware should be washed with soap and water after each use. When your boat is used in a corrosive environment such as saltwater, water with a high sulfur content or polluted water, the stainless steel will periodically develop surface rust stains. This is perfectly normal under these conditions.
YOU SHOULD CONTACT PURSUIT CUSTOMER RELATIONS BEFORE MAKING ANY MODIFICATIONS TO ALUMINUM FABRICATIONS. UNAUTHORIZED MODIFICATIONS CAN VOID THE WARRANTY. NOTICE CHROME HARDWARE Use a good chrome cleaner and polish on all chrome hardware. ACRYLIC PLASTIC ACRYLIC GLASS SCRATCHES EASILY. NEVER USE A DRY CLOTH OR GLASS CLEANING SOLUTIONS ON ACRYLIC. USE A SOFT CLOTH AND MILD SOAP AND WATER FOR ROUTINE CLEANING. SOLVENTS AND PRODUCTS CONTAINING AMMONIA CAN PERMANENTLY DAMAGE ACRYLIC PLASTIC.
CORIAN® SURFACES Although Corian® is quite resistant to heat, you should always use a hot pad or a trivet with rubber feet to protect Corian®. Avoid exposing Corian® to strong chemicals, such as paint removers, oven cleaners, etc. If contact occurs, quickly flush the surface with water. Soapy water or ammonia-based cleaners will remove most dirt and stains from all types of finishes. Do not cut directly on Corian® countertops.
become badly soiled. Dirt, oil, mildew, and cleaning agents containing ammonia will shorten the life of the vinyl that is used for clear curtains. After cleaning the curtains and allowing them to dry, apply a non-lemon furniture polish or an acrylic glass and clear plastic protector to extend the life of the curtains. Vinyl curtains should be stored either rolled or flat, without folds or creases. Folding the curtains will make permanent creases that could cause the vinyl to crack.
11.5 Bilge To keep the bilge clean and fresh, use a commercial bilge cleaner regularly. Follow the directions carefully. All exposed pumps and metal components should be sprayed periodically with a protector to reduce the corrosive effects of the high humidity always present in these areas. 11.6 Generator (Optional) The engine maintenance required on the generator is similar in many ways to any inboard engine.
Operator Notes 100 3480 DRUMMOND RUNNER
Chapter 12: SEASONAL MAINTENANCE 12.1 Storage and Lay-up BEFORE HAULING: • Pump out the head. Flush the holding tank using clean soap, water and a deodorizer. Pump out the cleaning solution. • The fuel tank should be left nearly full to reduce condensation that can accumulate in the fuel tank. Allow enough room in the tank for the fuel to expand without leaking out the vents.
BOATS CAN BE DAMAGED FROM IMPROPER LIFTING AND ROUGH HANDLING WHEN BEING TRANSPORTED BY LIFT TRUCKS. CARE AND PROPER HANDLING PROCEDURES MUST BE USED WHEN USING A LIFT TRUCK TO MOVE THE BOAT. NEVER ATTEMPT TO LIFT THE BOAT WITH A SUBSTANTIAL AMOUNT OF WATER IN THE BILGE. SEVERE GELCOAT CRACKING OR MORE SERIOUS HULL DAMAGE CAN OCCUR DURING HAULING AND LAUNCHING IF PRESSURE IS CREATED ON THE GUNWALES (SHEER) BY THE SLINGS.
PREPARING THE BOAT FOR STORAGE: • Remove the bilge drain plug(s), if installed. • Thoroughly wash the fiberglass exterior, especially the antifouling portion of the bottom. Remove as much marine growth as possible. Lightly wax the exterior fiberglass components. • Remove all oxidation from the exterior hardware and apply a light film of moisture displacing lubricant. • Remove propellers and grease the propeller shafts using light waterproof grease. • Remove the batteries and store in a cool place.
The shower/cabin drain sump system must be properly winterized. Clean debris from the drain and sump and flush for several minutes with fresh clean water. After the system is clean, pump the drain sump as dry as possible. Then pour a potable water antifreeze mixture into the shower drain until antifreeze has been pumped through the entire system and out of the thru-hull. For additional information please refer to the Plumbing Systems chapter. RAW WATER SYSTEM Completely drain the raw water systems.
The air conditioner components must be properly winterized by following winterizing procedure in the air conditioner owner’s manual. The air conditioning, engine control system, head and steering systems have specific lay-up requirements. Please refer to the owner’s manuals for recommended winterizing procedures. BILGE Coat all metal components, wire busses, and connector plugs in the bilge with a protecting oil. It is also important to protect all strainers, seacocks and steering components.
PLACING AN ELECTRIC OR FUEL BURNING HEATING UNIT IN THE BILGE AREA CAN BE POTENTIALLY HAZARDOUS AND IS NOT RECOMMENDED. Proper storage is very important to prevent serious damage to the boat. If the boat is to be stored indoors, make sure the building has enough ventilation. It is very important that there is enough ventilation both inside the boat and around the boat. If the boat is to be stored indoors or outdoors, open all drawers, clothes lockers, cabinets, and doors a little.
• Clean and wash the boat. • Install all upholstery, cushions and canvas. AFTER LAUNCHING: • Carefully check all water systems and the engine bolts for leaks. Operate each system one at a time checking for leaks and proper operation. • Check the bilge pump manual and automatic switches. • When the engines start, check the cooling system port below the engine cowling for a strong stream of water. This ensures that the cooling pump is operating.
Operator Notes 108 3480 DRUMMOND RUNNER
Appendix A: GLOSSARY OF TERMS Aft: In, near, or toward the stern of a boat. Aground: A boat stuck on the bottom. Amidships: In or toward the part of a boat midway between the bow and stern. Anchor: A specially shaped heavy metal device designed to dig efficiently into the bottom under a body of water and hold a boat in place. Anchorage: An area specifically designated by governmental authorities in which boats may anchor. Ashore: On shore. Astern: Behind the boat, to move backwards.
Bridge: The area from which a boat is steered and controlled. Bridge Deck: A deck forward and usually above the cockpit deck. Broach: When the boat is sideways to the seas and in danger of capsizing; a very dangerous situation that should be avoided. Bulkhead: Vertical partition or wall separating compartments of a boat. Cabin: Enclosed superstructure above the main deck level. Capsize: When a boat lays on its side or turns over.
EPIRB: Emergency Position Indicating Radio Beacon. Operates as a part of a worldwide satellite distress system. Even Keel: When a boat floats properly as designed. Fathom: A measure of depth. One Fathom = 6 feet. Fender: A soft object of rubber or plastic used to protect the topsides from scarring and rubbing against a dock or another vessel. Fend off: To push or hold the boat off from the dock or another boat. Flying Bridge: A control station above the level of the deck or cabin.
Helm: The steering and control area of a boat. Hull: The part of the boat from the deck down. Inboard: A boat with the engine mounted within the hull of the boat. Also refers to the center of the boat away from the sides. Inboard/outboard: Also stern drive or I/O. A boat with an inboard engine attached to an outboard drive unit. Keel: A plate or timber plate running lengthwise along the center of the bottom of a boat. Knot: Unit of speed indicating nautical miles per hour.
Moored: A boat secured with cables, lines or anchors. Mooring: An anchor permanently embedded in the bottom of a harbor that is used to secure a boat. Nautical Mile: A unit of measure equal to one minute of latitude. (6076 feet) Nun Buoy: A red or red-striped buoy of conical shape. Outboard: A boat designed for an engine to be mounted on the transom. Also a term that refers to objects away from the center line or beyond the hull sides of a boat.
Rubrail: Railing (often rubber or hard plastic) that runs along the boat’s sheer to protect the hull when coming alongside docks, piers, or other boats. Rudder: A moveable flat surface that is attached vertically at or near the stern for steering. Sea anchor: An anchor that does not touch the bottom. Provides drag to hold the bow in the most favorable position in heavy seas. Scupper: An opening in the hull side or transom of the boat through which water on deck or in the cockpit is drained overboard.
Swimming Ladder: Much the same as the boarding ladder except that it extends down into the water. Taffrail: Rail around the rear of the cockpit. Thru-hull: A fitting used to pass fluids (usually water) through the hull surface, either above or below the waterline. Topsides: The side skin of a boat between the waterline or chine and deck. Transom: A flat stern at right angles to the keel. Travel Lift: A machine used at boat yards to hoist boats out of and back into the water.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 116 3480 DRUMMOND RUNNER
Appendix B: MAINTENANCE SCHEDULE AND LOG Ea MAINTENANCE ch W U se ee M kl y on Ea ch th ly Y Se as on A ea rly sN ee de d X Clean hull below the waterline Bottom paint hull X X X X X Check sacrificial anodes Replace sacrificial anodes X Wash boat canvas & hardware X X Wax exterior gelcoat X X Clean & protect hardware X Polish & protect plastic glass X X Clean exterior upholstery X X Clean cabin & interior upholstery X Flush engine with fresh water Spray metal compon
MAINTENANCE LOG Date Hours 118 Dealer Service/Repairs 3480 DRUMMOND RUNNER
MAINTENANCE LOG Date Hours Dealer 3480 DRUMMOND RUNNER Service/Repairs 119
MAINTENANCE LOG Date Hours 120 Dealer Service/Repairs 3480 DRUMMOND RUNNER
MAINTENANCE LOG Date Hours Dealer 3480 DRUMMOND RUNNER Service/Repairs 121
MAINTENANCE LOG Date Hours 122 Dealer Service/Repairs 3480 DRUMMOND RUNNER
Appendix C: DEPARTMENT OF TRANSPORTATION U.S. COAST GUARD C.G. 1865 (REV. 1/88) BOATING ACCIDENT REPORT FORM APPROVED OMB NO.211-0010 The operator/owner of a vessel used for recreational purposes is required to file a report in writing whenever an accident results in: loss of life or disappearance from a vessel, or an injury which requires medical treatment beyond first aid: or property damage in excess of $200 or complete loss of the vessel.
BOATING ACCIDENT REPORT If more than 3 fatalities and/or injuries, attach additional form(s) DECEASED NAME ADDRESS DATE OF BIRTH WAS VICTIM? [ ] Swimmer [ ] Non Swimmer DEATH CAUSED BY [ ] Drowning [ ] Other [ ] DISAPPEARANCE WAS PFD WORN? [ ] Yes [ ] No What Type? NAME ADDRESS DATE OF BIRTH WAS VICTIM? [ ] Swimmer [ ] Non Swimmer DEATH CAUSED BY [ ] Drowning [ ] Other [ ] DISAPPEARANCE WAS PFD WORN? [ ] Yes [ ] No What Type? NAME ADDRESS DATE OF BIRTH WAS VICTIM? [ ] Swimmer [ ] Non Swimmer
Appendix D: Float Plan Pursuit recommends filling out a float plan each time you use your boat for an offshore day trip or a long cruise. Leave this information with a responsible person ashore, like a close friend or relative that you know well. 1. Name of person reporting and telephone number. 2. Description of boat. Type Registration No. Name 3. 4. Trim Length Other Info Make Engine type No. of Engines H.P.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 126 3480 DRUMMOND RUNNER
Appendix E: TROUBLESHOOTING GUIDE PROBLEM CAUSE AND SOLUTION CONTROL SYSTEMS Hydraulic Steering is slow to respond & erratic. • Steering system is low on fluid. Fill and bleed system. • Steering system has air in it. Fill and bleed system. • A component in the steering system is binding. Check and adjust or repair binding component. • Engine steering spindle is binding. Grease spindle. The boat wanders and will not hold a course at cruise speeds. • There could be air in the steering system.
TROUBLESHOOTING GUIDE PROBLEM CAUSE AND SOLUTION ENGINE PROBLEMS The engine is running too hot. • The engine raw water pick up strainer up is clogged with marine growth. Clean pick up • The engine raw water pump impeller is worn or damaged. Repair the pump. • The engine thermostat is faulty and needs to be replaced. The engine alternator is not charging properly. • The battery cable is loose or corroded. Clean and tighten battery cables. • The alternator is not charging and must be replaced.
TROUBLESHOOTING GUIDE PROBLEM CAUSE AND SOLUTION ACCESSORY PROBLEMS The livewell pump runs, but does not pump water. • The strainer on the intake scoop is clogged preventing the water from getting to the pump. Put the boat in reverse to clean the strainer. • There is an air lock in the system. Run the boat above 15 m.p.h. and the pick up scoop will force the air lock past the pump and prime the system. • The thru-hull valve is not open. Open valve. • The valve in the livewell is not open.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 130 3480 DRUMMOND RUNNER
