Safety Data Sheets (SDS)

ManualsBrandsPVC PipeWorks ManualsPVC Pipe & FittingsPipeworks 1/2" Dome Furniture Grade PVC Cap - 10 Pack

Table Of Contents

PIPEW RKS

Date Revised: JAN 2020

Supersedes: SEP 2018

GHS SAFETY DATA SHEET

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

SECTION 2 - HAZARDS IDENTIFICATION

As defined in the OSHA Hazard Communication Standard, 29 CFR 1910.1200, the products provided

below are considered articles and therefore the GHS labeling elements are not included on this SDS. All

components listed for this product are bound within the product. When handled as intended and under

normal conditions of use, there is no significant health risk.

NOTE: This product releases corrosive & toxic gases when burned (e.g., hydrogen chloride gas). Avoid

generating dust. Wear a self-contained breathing apparatus (SCBA). Personnel not having a SCBA should

leave the area immediately and avoid smoke inhalation.

PRODUCT NAME

PVC Pipeworks PVC Pipe and Fittings

PRODUCT USE

Structural and Framework PVC Pipe and Fittings

Manufacturer

PVC Pipeworks

17501 W 98th Street, Pillar 18-43

Lenexa, KS 66219

United States

Manufacturer’s Product Code

Varies

HAZARDS IDENTIFICATION

Physical Hazards

None Classified

Health Hazards

None Classified

OSHA Defined Hazards

None Classified

Hazard(s) not Otherwise

Classified (HNOC)

None Classified

PRECAUTIONARY STATEMENT

Prevention

Observe good industrial hygiene practices

Response

Wash hands after handling in quantity

Storage

Store away from incompatible materials

Disposal

Dispose of or recycle waste and residues in accordance with local authority

requirements

LABEL ELEMENTS

Hazard Symbol

None Required

Signal Word

None Required

Hazard Statement

None Required

Summary of content (6 pages)

PAGE 1
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 GHS SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME PVC Pipeworks PVC Pipe and Fittings PRODUCT USE Structural and Framework PVC Pipe and Fittings Manufacturer PVC Pipeworks 17501 W 98th Street, Pillar 18-43 Lenexa, KS 66219 United States Manufacturer’s Product Code Varies SECTION 2 - HAZARDS IDENTIFICATION As defined in the OSHA Hazard Communication Standard, 29 CFR 1910.
PAGE 2
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 SECTION 3 - HAZARDOUS INGREDIENTS: COMPOSITION/INFORMATION INGREDIENT % WEIGHT PEL-OSHA TLV-ACGIH NIOSH REL Polyvinyl Chloride Resin >80% None established 10 mg/m3 None established PVC Additives ≤ 20% None established 10 mg/m3 None established SECTION 4 - FIRST AID MEASURES Dust resulting from power or hand sawing this material is considered to be a low health risk by inhalation.
PAGE 3
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 SECTION 5 - FIREFIGHTING MEASURES FLAMMABLE PROPERTIES Flash Point No Data Dust and particulates milled from products may be combustible. FLAMMABLE LIMITS LEL No Data UEL No Data Extinguishing Media Water or Foam medium is preferred. CO2 and Dry Chemical methods are suitable but not preferred Fire and Explosion Hazards Releases corrosive & toxic gases when burned (e.g.
PAGE 4
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 SECTION 8 - PRECAUTIONS TO CONTROL EXPOSURE / PERSONAL PROTECTION Eye Protection When cutting, wear safety glasses or goggles to prevent particles from being projected into eyes. Inhalation Protection Use with adequate ventilation to meet exposure limits listed under Section 3. Where the exposure limits are or may be exceeded, use NIOSH approved respiratory protection. Skin Protection When handling hot material, use heat resistant gloves.
PAGE 5
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 SECTION 10 - STABILITY AND REACTIVITY ACUTE TOXICITY No toxicological data is available for the finished product REPRODUCTIVE TOXICITY Not Available SENSITIZATION Not Available TERATOGENICITY Not Available MUTAGENICITY Not Available SPECIFIC TARGET ORGANS – SINGLE EXPOSURE Not Available DEVELOPMENTAL Not Available SPECIFIC TARGET ORGANS – REPEATED EXPOSURE Not Available FERTILITY Not Available ASPIRATION HAZARD Not Available CARCINO
PAGE 6
PIPEW RKS Date Revised: JAN 2020 Supersedes: SEP 2018 SECTION V - HEALTH HAZARD DATA Exposure There are no significant health hazards from exposure to the product in rigid form at ambient temperatures. Routes of Entry and First Aid Measures Inhalation (Nose & Throat) –. Operations involving heating (forming) of PVC sufficient to result in degradation should be examined to ensure proper ventilation. Cutting and drilling PVC will release nuisance dust particles which are non-toxic.