Product Brochure

GET IT TOGETHER
tm
The properties represented herein are TYPICAL VALUES and not intended for use in specifications. Extreme Adhesives, LLC
MAKES NO EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY , FITNESS OR OTHERWISE . While the information presented is believed to be accurate, no warranty or recommendation is
made as to application. Determination of product suitability is the sole responsibility of the user. Suggestions made do not constitute any guarantee in as much as use conditions are
beyond our control.
EXTREME Adhesives 63 Epping Road Raymond, NH 03077
Division of Royal Adhesives & Sealants, LLC
PH 603-895-4028 - FAX [phone]
http://www.pvctrimwelder.com http://www.extremeadhesives.com
FAST CURE
Product Description
EXTREME Adhesives tm PVC T RIM W ELDER tm Adhesive
is a medium viscosity, solvent-free structural adhesive
system that provides flexibility, toughness and surface
adhesion for bonding all forms of PVC to itself metals or
wood. Cured performance shows excellent adhesion and
bond strength to nylons, polystyrenes, fiberglass, reinforced
plastics, stone, ceramics and most plain and plated metal
components. This material can withstand thermal cycling
and shock loading between dissimilar materials. Fast Cure
PVC T RIM W ELDER tm Adhesive is ready to handle in 10-
30 minutes
EXTREME Adhesives tm PVC T RIM W ELDER tm Adhesive
does not require special surface prep and does not contain
any solvents. Will work successfully in most applications
without preparation. It’s so strong it appears to weld the PVC
together. Creamy consistency, won’t foam, run or drip.
EXTREME Adhesives tm PVC T RIM W ELDER tm Adhesive
is a fast curing, two-component product with an open time of
4 - 7 minutes at 73ºF after thorough mixing. EXTREME
Adhesives tm PVC T RIM W ELDER tm will cure satisfactorily at
application temperatures as low as 20º F
Why Should You Select This Adhesive?
• Permanent Unitizing Structural Adhesive
• Excellent Adhesion to PVC
• Impact Resistance - Peel Strength
• UV Resistance
• Matches white PVC Trim Boards
• Paintable
• Fast Setting
• Easy to apply
• Fills Nail Holes and Gaps
• Meets 2009 EPA VOC & CARB requirements
Contact an EXTREME ADHESIVES

Adhesive
Applications Specialist for further recommendations on
adhesive selection.
Physical Properties
Typical Uncured Properties (LIQUID)
Applies to both adhesive and activator sides
Viscosity
50,000cps mixed
Specific Gravity
1.01 (20/20Cº)
Color
White
Flashpoint
51ºF (COC method)
Toxicity
Moderate, see MSDS
Solvents
None
Mix Ratio
1 : 1
Fillers
Yes
Clean Up Solvents
MEK, Acetone
Typical Cured Properties (SOLID)
Typical film thickness 0.030".
Shore
D Hardness
75
Adhesive testing on
plastics, PVC, ABS glass
filled nylon, styrene
Substrate Failure
Thermal Service Range
-
65ºF to 260ºF
Chemical Resistance
Excellent
Elongation
60%
Impact Resistance
20 ftlbs/in
2
on S
teel
Peel Strength
20
-
25 psi on Aluminum
Lap Shear Strength
2340 psi
-
as rec’d CRS
3390 psi – aluminum
3365 psi grit blasted steel
Instructions For Use
Combine resin and activator in equal volume and
mix thoroughly. For convenience and accuracy use
pre-measured cartridges with disposable static
mixers. Open time is 4 - 7 minutes at room temperature.
Handling strength within approximately 10-30 minutes.
Shelf Life
Shelf Life is 12 months when properly stored in an unopened
original container in a cool, dark area between 55°F to 75°F.