User's Manual

RCZ1 - 868MHz(Europe)
RCZ2 - 902MHz (US, Canada and Mexico)
RCZ3 - (Japan and Korea)
RCZ4 - 920-922MHz (ANZ, Lan America and S-E Asia)
SiPy 1.0
With Sigfox, WiFi and BLE, the SiPy is the latest Pycom triple-
bearer MicroPython enabled micro controller on the market
today – the perfect enterprise grade IoT plaorm for your con-
nected Things. With the latest Espressif chipset the SiPy oers a
complete combinaon of power, friendliness and exibility.
Create and connect your things everywhere. Fast.
Distributed by Pycom Ltd.
Copyright © 2016 by Pycom Ltd. All rights reserved. No part of
this document may be reproduced, distributed, or transmied
in any form or by any means, including photocopying, recording,
or other electronic or mechanical methods, without the prior
- Espressif ESP32 chipset
- Dual processor + WiFi radio System on Chip.
- Network processor handles the WiFi connecvity and the IPv6
stack
- Main processor is enrely free to run the user applicaon
- An extra ULP-coprocessor that can monitor GPIOs, the ADC
channels and control most of the internal peripherals during
deep-sleep mode while only consuming 25uA
- Powerful CPU, BLE and state of the art WiFi radio
-1KM Wi Range
- MicroPython enabled
- Fits in a standard breadboard (with headers)
- Ultra-low power usage: a fracon compared to other connected
micro controllers
SiPy Features
Use the Pymakr IDE
Super easy code editor to write your Python scripts
Quick Vericaon
For easy and fast debugging use the interacve shell that is
accessible through telnet or one of the serial ports
Easy Upload
Upload your scripts, and any other les you want to the SiPy via
the FTP server
Locally or remotely
Reset the SiPy (you can do it locally, or remotely via Telnet)
Mechanical
Processing
Hash / encryption
SHA, MD5, DES, AES
WiFi Networking
802.11b/g/n 16mbps
Bluetooth
Low energy and classic
RTC
Running at 32KHz
Range
Node range: Up to 50km
- 2 x UART, 2 x SPI, I2C, I2S, micro SD card
- Analog channels: 8x12 bit ADCs
- Timers: 4x16 bit with PWM and input capture
- DMA on all peripherals
- GPIO: Up to 24
- Voltage Input: 3.3V - 5.5V
- 3v3 output capable of sourcing up to 400mA
- WiFi: 12mA in acve mode, 5uA in standby
- Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA
in standby
- Sigfox (Austrailia, New Zealand and South America): 24mA in Rx
mode, 257 mA in Tx mode and 0.5uA in standby
Interfaces
Power
Size: 55mm x 20mm x 3.5mm
Security & Certications
- SSL/TLS support
- WPA Enterprise security
- AES encrypon engine
Memory
- RAM: 512kb
- Flash Memory: 4MB
- GPIO: Upto 24
- Hardware oang point
acceleraon
- Python mul-threading
wrien permission of Pycom Ltd, except in the case of brief
quotaons embodied in crical reviews and certain other
noncommercial uses permied by copyright law.
To order contact [e-mail]
- TI CC1125NarrowbandTransceiver
- Class 0 device. Maximum Tx power:
- +14dBm(Europe)
- +22dBm (America)
- +22dBm (Australia and New Zealand)
- Node range: Up to 50km
- Sigfox pre-cered (October 2016)
Sigfox Operating Frequencies
Sigfox Speciction
External LoRa antenna
connector
Reset switch
32Mbit ash memory
SIGFOX
transceiver
U.FL connector
RF switch
ESP32 Dual Core
Microcontroller and
WiFi/Bluetooth 4.2
radio
Internal WiFi and
Bluetooth Antenna
With dozens of ready to use templates and libraries soon to
be available on the Pycom Exchange, developing a new IoT
soluon is now easier and faster.
WS2812 RGB
mul-colour
LED
3V3 Ultra-Low
-Noise switching
regulator
Operang temperature:
-40 to 85 degrees celsius
Si