PLCHD6 6 - DISC CD CHANGER INSTRUCTION MANUAL
IMPORTANT NOTICE This Compact Disc Changer/Player has been tested and found to comply with the limits for a class B digital device in accordance with the specifications in Subpart J of part 15 of FCC Rules. This equipment generates and uses radio frequency energy, and it must be installed and used properly in accordance with the manufacturer's instructions. CAUTION This product is designed for 12 Volt DC Negative ground systems only.
INTRODUCTION RESET FUNCTION A RESET button is located on the front panel (to the left side of EJECT button) and is accessible only when the magazine door is opened. The RESET button is recessed in order to prevent accidental engagement, and can be activated with the tip of ballpoint pen or any similar pointed object. The reset circuitry is provided in order to protect the unit's microprocessor and tracking system and should be activated only under the following conditions: a.
LOCATION OF CONTROLS 1. Compact Disc Magazine Slot 2. Reset Button 3. Eject Button (Press this button to eject the Magazine) 4.
HOW TO USE THE COMPACT DISC MAGAZINE Inserting Discs Inserting Discs into the supplied magazine. Up to 6 Discs may be inserted into the magazine. The Disc are numbered from 1 (bottom tray) to 6 (top tray). Note: Do not touch the recorded side of a Disc while inserting or removing it. Removing Discs 1. Press the Eject button to remove the Magazine. 2. Push the Release keys to remove the Discs. Precautions • Do not leave the magazine exposed to high temperature or direct sunlight.
INSTALLATION • Use the supplied parts and mount the unit securely. The use of parts other than these supplied (specified) may loosen or damage internal components. • If installation presents any difficulties, consult your dealer for advice. • Before drilling a hole into the wall or floor the vehicle trunk, check that nothing is behind the panel. Never drill a hole in the fuel tank or any other important that may be attached to the trunk.
ACCESSORIES x2 a) Bracket x4 d) Wing nut (06) x2 b) Floor base plate x4 e) Self tape screw (5x15) x4 c) Hex bolt (M5x12) with Washers x4 x1 f) Self tape screw (3x15) g) Mount angle adjust key Important Angle set and locking screws • Be sure to adjust the mounting angle set screw (F) using the mounting angle adjust key to appropriate angle: Of for horizontal. 45° angle. or 90° for vertical mounting.
INSTALLATION DIAGRAMS HORIZONTAL / VERTICAL INSTALLATION PROCEDURES 1. Attach the brackets (a) to each side of the unit. Using the hex bolts with washers (c). 2. Determine the mounting location and drill 4 mounting holes approximately 3.5mm in diameter . 3. Secure the unit in place using 4 self-tapping screws (e). e) e) c) c) e) e) a) a) ø3.5mm ø3.
VERTICAL INSTALLATION c) e) a) b) d) a) b) c) Attach the brackets (a) to each side of the unit using hex bolts with washers (c). Attach the floor base plate (b) to the brackets a) using the wing nuts (d) Lift the carpet and determine the mounting location. Fix the floor base plate (b) to the floor using self-tape screw (f). d) d) d) Press the unit to the floor, and remove the wing nuts (d), and lift off the changer d) Lay down the carpet.
SPECIFICATIONS General System Usable Discs Operation voltage Power consumption Operating electric current Max. peak electric current Dimensions Operational temperature range Temperature range of storage Test condition Audio Frequency range Dynamic range Distortion (THO N) S/N ratio Channel separation Audio output level Wow & Flutter SCRATCH INTERRUPTION BLACK DOT FINGER PRINT Compact Disc audio system Compact Disc 10 - 15V 6W or less (DC 14.4V) 400mA 14.4Volt 1.2A 14.4Volt 284(W) x 186.
OPERATION Liquid Crystal Display (LCD) - (1) LCD display will only be active when the changer power is on. This display indicates all operation key's, including DISC number. Track number, and DISC icon. Random Play Button - (2) (Track or DISC Random) This is used for random selection Disc play, and sequence. Once this button is pressed. "RDM" is displayed in the Upper left corner of LCD commander, and disc selection will begin random play.
ERROR DISPLAY • Error 1: • Error 2: • Error 3: • Error 4: • Error 5: There's no Magazine, and DISC is clamping. It is impossible to discharge Magazine while ejecting. Loading is not completed after a certain time (8 sec) passed. Unloading is not completed after a certain time (8 sec) passed. Elevator does not reach to the target position after a certain time (8 sec) passed. Hole separated.
