Model:P27 LCDD 16:9 DIGITAL LCD-TV-Monitor 26 Hi-Definition LCD Flat Panel TV w/Built-in DVD Player OPERATING MANUAL
Contents 1 PREFACE 3 2 SAFETY PRECAUTIONS 3 3 FRONT, BACK, CONNECTIONS OF LCD 5 4 TV INSTALLATION GUIDE 4.1 CONNECTION ANTENNAS 7 4.2 AV VIDEO INPUT DRAWING 7 4.3 S-VIDEO INPUT DRAWING 7 4.
Contents 8 THE DVD SETUP MENU SYSTEM 8.1 Basic Operation 23 8.2 DVD Setup Mode 23 8.2.1 General Setup 23 8.2.2 8.2.2 Speaker Setup Page 25 8.2.3 Dolby Digital Setup 25 8.2.4 Video Setup 26 8.2.
PREFACE Thank you for buying this TV ! Please read this manual thoroughly before operating the monitor. Make sure the monitor was not damaged in transit. Should the monitor is damaged, do no install it and contact your dealer. Check that you have all the accessories according to the model. SAFETY PRECAUTIONS Preparation Put the monitor on a stable surface. Do not use the monitor with others fixations than those provided or suggested by the manufacturer.
Heating sources and humidity Keep the monitor dry and away from humidity. Keep the monitor away from heat sources Cleaning and maintenance Unplug the monitor before cleaning it. Do not use solvents or liquids to clean the monitor. Only clean the monitor with a soft and dry cloth. In case of troubleshooting, do not use spare parts other than those suggested by the manufacturer. Using inadequate spare parts can lead to electric shocks, short-circuits fire or other incidents.
Front , Back , Connections of LCD Front View VOL VOL CH CH IR MENU SOURCE ON / OFF LED POWER Back View and Control Connections 13 14 15 16 17 18 L1 L2 L Y1 Pb1 Pr1 R1 R2 R Y2 Pb2 Pr2 19 CVBS PC IN HDMI2 12 11 10 9 8 7 6 5 RF inp ut S VI DEO PC AUDIO IN 4 HDMI1 3 2 1 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 RF input S VIDEOIN HDMI1 HDMI2 PC IN PC AUDIO IN Pr2 Pb2 Y2 R(CVBS/S-VIDEO) R2(YPbPr2) R1 (YPbPr 1 ) L1(YPbPr1) L2(YPbPr2) L(CVBS/S-VIDEO) Y1 Pb1 Pr1 C
Side View DVD Player Control Disc Slot inside (Label side toward user) DVD Function Keys : EJECT DISK BUTTON : PLAY / PAUSE : STOP 6
TV INSTALLTION DRAWINGS CONNECTION ANTENNAS VHF ANTENNA VHF ANTENNA OUTDOOR ANTENNA AMPLIFIER INDOOR ANTENNA AMPLIFIER 75 OHM ANTENNA PLUG POWER PLUG OF ANTENNA AMPLIFIER To ensure good picture and sound, TV antenna system needs to be installed. The antenna system as shown can be sourced from TV equipment shops, which will provide service for correct installation and connection. After installation, insert the 75-ohm antenna plug into the antenna jack as shown.
PCINPUT CONNECTION PC IN PC AUDIO IN L1 L2 L Y1 Pb1 Pr1 R1 R2 R Y2 Pb2 Pr2 C VB S PC IN S V ID EO PC AUDIO I N HDM I2 8 H DM I1 R F input
Menu Operation 1. Connecting to the AC input cable then press the main power switch to switch ON LCD TV. At this time the TV will enter standby mode and indicator show red. 2. Use POWER button can turn ON LCD TV from standby mode. 1. Press POWER button or button on the remote control to enter standby mode. The indicator is red. 2. Using main power switch turns off LCD TV completely.
Menu Operation - Press the MENU button to display the main menu. - Use / Picture Audio Setup Feature Picture Audio / / buttons to select and adjust the available menus.
Menu Operation Ch2-1 Video 1 Composite Rear Video 2 Component-1 Video 3 Component-2 Video 4 VGA Video 5 HDMI -1 Video 6 HDMI -2 Video 7 S-Video In this manual, the OSD ( On Screen Display) may be different from your TV’ s because it is just example to help the TV operation. Picture Audio Setup Feature Picture Mode Contrast 50 Brightness 50 Sharpness 50 Color 50 Tint 50 User 1. Use / to select what you want to adjust in the Picture menu. Aspect Ratio To Move Wide To Select E nter Menu 2.
Menu Operation Picture Audio Setup Feature Audio Mod e Audio Lan guage Bass 30 Treble 30 Balance 0 Voice English Digital Audio Output 1. Use / to select what you want to adjust in the Audio menu. PCM 2. Press To Move To Select Enter Menu and button to adjust. 3. When you are satisfied with your adjustment, press MENU or EXIT to exit the main menu. To Exit You can select the type of sound which best corresponds to your listening requirements by selecting Sound in SOUND menu.
Menu Operation Press ▲ / ▼ key to move the cursor to the item to be selected (item selected is highlighted in yellow). Press Enter key to enter your selection and scan. After the scan is finished, the following menu will display. The channels found are automatically saved as below: Autoprogram Menu NTSC Channel 19 Not Found Analog Channels Found 2 Digital Channels Found 0 Progress(%) When the channels are found, use / 12 to add it to the channel list.
Menu Operation P ictur e Audio Time Set Sle ep Time r Adva nced Video M enu Off Passw ord Se t 1. Use / to select what you want to adjust in the Feature menu. Paren ta l Co n tro l S etup Fe ature Press / D ig ita l Cl osed C aption 2. Press To Move Enter To Select Menu and button to adjust. 3. When you are satisfied with your adjustment, press MENU to exit the main menu. To Exit button and then use Enter the time set menu as below that allows you to set the time the TV will display.
Menu Operation - Noise Reduction--Spatial: press Enter to select on or off. - Noise Reduction--Speckle: press Enter to select on or off. - Noise Reduction--Temporal: press Enter to select on or off. - Auto Contrast Enhancement: press Enter to select on or off. - Color Temperature: press Enter to select one of Normal/Cool and Warm. - 3D Y/C: press Enter to select on or off. - Adaptive Contrast: press Enter to select on or off. - Setting: press Enter to return to the factory setting.
Menu Operation - Style: press Enter to select one of Automatic and Custom, when you select automatic, the others are disable and can not be adjusted. - Size: press Enter to select one of Normal/Large and Small. - Font: press Enter to select one of Default and from Font1 to Font7. - Text Color: press Enter to select one of Red/Green/Blue/Yellow/Magenta/Cyan/Black and White. - Text Opacity: press Enter to select one of the Solid/Flashing/Transparent/Translucent.
Menu Operation -Phase This function allows you to remove any horizontal noise and clear or sharpen the image of characters -Clock This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size also will change. -Position This function is to adjust the picture to Left/Right and Up/Down as you prefer.. Press / button and then use configuration.
Menu Operation Time Set Sleep Timer Picture Off Advanced Video Menu Audio Setup Feature Press / To Move Ent er To Select Me nu To Exit button and then use Enter the time set menu as below that allows you to set the time the TV will display. Press ◄/► to select the amount of time before your TV turn off automatically and press the Enter that can select the 30 min /60min/90min and OFF. Press Enter to enter the advance video menu.
REMOTE CONTROL Remote control instructions Switch on LCD TV when at standby mode or vice versa. MTS Press to mute the sound. Press again or press VOL+ to unmute. Press to cycle through the input source in following: Ch Video1 Video3 Video4 Video2 Video7 MENU CCD EXIT Video6 Video5 DISPLAY Press repeatedly to cycle through the available video picture modes. Press to cycle through the different sound settings. Audio selection button.
Brings up the main menu to the screen. Closed caption button. MTS Clears all on-screen displays and returns to TV viewing from any menu. Press to display the source and channel’s information. MENU CCD EXIT DISPLAY Allows you to navigate the on-screen menus and adjust the system settings to your preference. Press to scan through channels. To scan quickly channels, press and hold down either +/-button. VOL CH VOL CH Press to increase / decrease the sound level. DVD SETUP ZOOM EPG D.
MTS PLAY/PAUSE Fast backward key. Fast forward key. MENU CCD EXIT DISPLAY Jump to previous track. Jump to next track. DVD THUMB STICK/OK. VOL CH VOL CH DVD STOP DVD SETUP ZOOM EPG D.
Battery Usage Caution a)Open the cover b)AA size batteries, When inserting the batteries, make sure correct polarities as per”+“and ”-“marks on the batteries and within the battery compartment c)Replace the battery cover To prevent battery leakage which may result in bodily injury or damage to the remote: 1.Install all batteries correctly, and as marked on the remote control. 2.Do not mix batteries:(OLD and NEW or CARBON and ALKALINE, etc) Remove batteries when the remote is not used for a long time.
THE DVD SETUP MENU SYSTEM 8.1 Basic Operation 1. Press TV/DVD button on the remote controller or DVD button on the TV set to turn on ( or off ) DVD . 2. Press OPEN / CLOSE button to load disc into disc tray. 3. Press OPEN / CLOSE button to close the tray. Hold the disc without touching either of its surfaces, position it with the printed title side facing up, align it with the guides, and place it in its proper position. 8 .
OSD Language This is used to select the OSD language. · English · French · Spanish Screen Saver Start the screen saver, the screen saver image will appear when the player stops or the picture is frozen for a few minutes. This saver can keep the screen from being damaged. · On (Start the screen saver) · Off (Remove the screen saver).
8.2.2 Speaker Setup Page Downmix · LT/RT A disc recorded multi channel soundtrack, the output signal will be incorporated to left and right channel. · Stereo A disc recorded multi channel soundtrack, The output signal will be incorporated to stereo. 8.2.3 Dolby Digital Setup Dual Mono This is used to select the Stereo, L-MONO, R-MONO and MIX-MONO.
Dynamic This option is used to set the compression ratio in order to control the sound (Vume) contrast. 8.2.
Brightness User can set the level of brightness for the image displayed. is ranged from -20 to 20. Contrast User can set the level of contrast for the image displayed. It is ranged from -16 to 16.
8.2.5 Preference Setup You must press STOP twice to enter Preference Page TV Type · PAL This is selected when the player is connected to an PAL System TV. · MULTI The player will set the TV system according to the disc in the tray. · NTSC This is selected when the player is connected to a NTSC System TV.
Audio If a language listed below is recorded on the disc, you can play the sound in such language. If not, the language recorded will be used. · English · French · Spanish · Chinese · Japanese · German · Duch · Italian Subtitle If a language listed below is recorded on the disc, you set the subtitle to be displayed in such language. If not, the language recorded will be used.
Disc Menu If a language listed below is record on the disc, you can set the Menu to be displayed in such language. If not, the language recorded will be used. · English · French · Spanish · Chinese · Japanese · German · Duch · Italian Parental When playing disc with parental lock function, you may select an Age Control Grade according to grade of disc and your own preference. For example, if PG is selected, DVD Video disc rated higher than the PG grade cannot be played.
Password User can change the password that is required when the user wants to change the Age Control Grade in the Parental Lock function. NOTE:(Default password is 3308 ) Default User can load the original factory setting by choose RESET and press OK button .
TROUBLESHOOTING AND ADVICE Before calling our SAS centre, please check if you can solve the troubleshooting by yourself. Troubleshooting Control No signal Please check that all cables and cord's are correctly plugged in. No color shades Adjust the contrast, the color and the brightness Stain show on the screen. May be result from a lighting signal from car, motor, neon light and other electrical devices or appliances.
SPECIFICATIONS Screen Size 26 Inch Display Type TFT Resolution(Pixel) 1366 * 768 Brightness 500cd/㎡ Color 16 . 2M Contrast Ratio 800 : 1 View Angle(H/V) 160 /150 Aspect Ratio 16:9 AC INPUT 110V/120V Voltage Selectable TV System NTSC Video Input Format NTSC Antenna Input Standard Audio Output antenna socket 75Ω L / R 20W*2 Video Video 1 . 0vp - p75Ω; RCA S-Video Y:1.0Vp-p±3db C:0.