PLCD12MRKT OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Automatically Memory Storing • Full Detachable Panel • Program CD Tracks • CD Changer Control • Auxiliary Input Function www.pyleaudio.
CONTENTS Installation .....................................................................................................3 DIN Front-Mount....................................................................................................3 Installing the unit.............................................................................................3 Removing the unit...........................................................................................4 Using the Detachable Front Panel ............
INSTALLATION Notes: TAKE OUT SCREW BEFORE INSTALL • The unit can be installed on the vehicle or the ships. Before install the unit, please remove the two screws. • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Take out screw before installation • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
INSTALLATION Removing the unit 1 6 1 2 5 3 7 4 Front Panel OPEN button (Fig. 2) 2 1. 2. 3. 4. 5. 6. Dashboard Nut (5mm) Spring washer Screw (5x25mm) Screw Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer 1. Before removing the unit, press the OPEN button to slide down the front panel. 2. Lever Insert the levers supplied with the unit into the grooves in the housing as shown in figure until they click.
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Reinstall the Front Panel 1. Press the OPEN button, the front panel will slide down. 1. When the panel bracket is in slide down position, insert the front panel into the panel bracket and push the front panel from the middle to slide it up. Open Bottom Button 2. When the front panel slides down, press the bottom button of the front panel upward and pull it out from the panel bracket. 2.
WIRING CONNECTION MAIN UNIT (BLACK) WIRING REMOTE CONNECTOR SOCKET (BLACK) CD CHANGER CONNECTOR SOCKET ANTENNA SOCKET IGNITION RED SWITCH (B+) FUSE AUX IN MEMORY YELLOW BACK-UP GROUND (B–) Lch WHITE BLACK (GREY) RCA CABLE POWER BLUE ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER (YELLOW) Rch RED Rch RED Lch WHITE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION CONTROL & FUNCTIONS KEYS 1 8 6 2 3 5 4 7 This unit is a marine rated wired remote control made using a modified controller or similar layout. It is capable of operation specified functions on the marine AM/FM/CD receiver. The body, buttons, controls and display need to be UV and water-resistant. It includes and LCD and an illumination circuit. The flat body should be watertight and the circuit board clear coated. 1 Power button Press the button (1) shortly to turn on/off the head unit.
OPERATION 4 MODE SELECTION button Press the MODE button (4) to step sequentially through the following sources: e.g. radio mode to CD mode (or to CDC cassette mode mode) to AUX to CDC in mode. mode to AUX in mode. 5 BAND SELECTION button Press the BAND button (5) to step sequentially through the following bands: FM1, FM2, FM3, AM1, AM1(MW1), AM2. AM2(MW2), LW. 6 TRACK/SEARCH/TUNE buttons • STATION SELECTION (FOR RADIO OPERATION) Press / buttons (6) shortly to activate automatic seek function.
INSTALLATION INSTALLATION HARDWARE HOLDER BASE REMOTE MOUNTING BRACKET X1 X1 X1 SCREW (ø4X50) NUT X2 X2 INSTALLATION DIAGRAM 1. First insert the hooks on the base into the slots of the holder to install the base to the holder. 2. Select the proper object, then place the remote mounting bracket on the base and let the object go through the base and the mounting bracket. 3.
OPERATION 16 9 11 10 6 12 13 17 19 8 20 1 21 14 22 23 24 5 18 2 3 4 15 7 25 • SOUND ADJUSTMENT Press SEL button (10) to select desired audio mode. The adjustment mode will change in the following order. GENERAL OPERATION • ON/OFF Switch on the unit by pressing PWR button (9). When system is on, press PWR button (9) again to turn off the unit. Press PWR button (9) for more than 2 seconds, the button is operated to initial volume control button.
OPERATION pressing button (17) to select Frequency Priority. Pressing DISP button (1) while in Frequency Priority will temporarily display clock. display. If you select beep sound on, whenever press any button, beep sound output. • LOUDNESS Press LOUD (DIM) button (15) shortly to reinforce the bass output and display will show “LOUD”. Press it again to release this function. • SELECTABLE CLOCK DISPLAY Programs the unit to display the clock (selectable on/off) when the unit is turned off.
OPERATION • STATION STORING Press any one of the preset buttons (14) (M1 to M6) (i.e.19~24) to select a station which had been stored in the memory. Press this button for several seconds, current station is stored into the number button. RADIO OPERATION • BAND SELECTION At tuner mode, press BAND button (18) shortly to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM1 • SCAN Press SCAN button (13) to scan through strong stations in the current band.
OPERATION select track 6, then press MEM button (20) to memorize it and “P02” will appear on the display. So track 6 will be played first. Thus, you can also press / buttons (17) and (16) to choose track number 10 and press MEM button, then “P03” will appear. So track 10 will be secondly played. Repeat these operations, and you can program CD tracks to your need. If you completed program setting, press PGM button (21) to play CD in programmed order.
OPERATION CD CHANGER OPERATION Note: • SELECT TRACKS Press button (16) or button (17) to move to the previous track or the following track. Track number shows on display. Hold press button (16) or button (17) to fast reverse or fast forward. Disc play starts from when you release the button. A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 178 (D) x 50 (H) mm : : : : ± 10 dB ± 10 dB 4 x 50 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
