PLCD18MRMP OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player/MP3 Player • Automatic Memory Storing • Slide Down Detachable Panel • Program CD Tracks • Electronic Shockproof (ESP) Function • CD Changer Control • Auxiliary Input Function www.pyleaudio.
CONTENTS Installation .....................................................................................................3 DIN Front-Mount....................................................................................................3 Installing the unit.............................................................................................3 Removing the unit...........................................................................................4 Using the Detachable Front Panel ............
INSTALLATION Notes: TAKE OUT SCREW BEFORE INSTALL • The unit can be installed on the vehicle or the ships. Before install the unit, please remove the two screws. • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Take out screws before installation • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
INSTALLATION Removing the unit 1 6 1 2 5 3 7 4 Front Panel OPEN button (Fig. 2) 2 1. 2. 3. 4. 5. 6. Dashboard Nut (5mm) Spring washer Screw (5x25mm) Screw Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer 1. Before removing the unit, press the OPEN button to slide down the front panel. 2. Lever Insert the levers supplied with the unit into the grooves in the housing as shown in figure until they click.
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Reinstall the Front Panel 1. Press the OPEN button, the front panel will slide down. 1. When the panel bracket is in slide down position, insert the front panel into the panel bracket and push the front panel from the middle to slide it up. Open Bottom Button 2. When the front panel slides down, press the bottom button of the front panel upward and pull it out from the panel bracket. 2.
WIRING CONNECTION MAIN UNIT (BLACK) ANTENNA SOCKET IGNITION SWITCH (B+) RED MEMORY BACK-UP YELLOW (BLACK) CD CHANGER AUX IN (GREY) REAR RCA CABLE GROUND (B–) FRONT Lch SPEAKER REAR Lch SPEAKER CONNECTOR SOCKET (YELLOW) Rch RED Lch WHITE BLACK POWER ANTENNA WIRING REMOTE CONNECTOR SOCKET Rch RED Lch WHITE BLUE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION CONTROL & FUNCTIONS KEYS 1 8 6 2 3 5 4 7 This unit is a marine rated wired remote control made using a modified controller or similar layout. It is capable of operation specified functions on the marine AM/FM/CD receiver and the marine AM/FM/Cassette receiver. The body, buttons, controls and display need to be UV and water-resistant. It includes and LCD and an illumination circuit. The flat body should be watertight and the circuit board clear coated.
OPERATION 4 MODE SELECTION button Press the MODE button (4) to step sequentially through the following sources: e.g. radio mode to CD mode (or cassette mode) to CDC mode to AUX in mode. 5 BAND SELECTION button FOR WEATHER BAND VERSION ONLY: Press the BAND button (5) to step sequentially through the following bands: FM1, FM2, AM, WX. 6 TRACK/SEARCH/TUNE buttons • STATION SELECTION (FOR RADIO OPERATION) Press / buttons (6) shortly to activate automatic seek function.
INSTALLATION INSTALLATION HARDWARE HOLDER BASE REMOTE MOUNTING BRACKET X1 X1 X1 SCREW (ø4X50) NUT X2 X2 INSTALLATION DIAGRAM 1. First insert the hooks on the base into the slots of the holder to install the base to the holder. 2. Select the proper object, then place the remote mounting bracket on the base and let the object go through the base and the mounting bracket.
INSTALLATION 3. Align the screw holes on the holder with the screw holes on the base and the screw holes on the bracket, then use the two screws (ø4X50) and nuts to fix the bracket, the base and holder to the proper location. 4. Last install the remote control to the holder. See below, align the four hooks on the holder with the four slots on the remote control.
OPERATION LOCATION OF KEYS 16 9 11 10 6 12 13 17 19 8 20 1 21 14 22 23 24 5 18 2 3 4 15 7 25 has not been adjusted for several seconds, the mode shall return to volume position and display will return to normal radio, CD or CDC display. GENERAL OPERATION • ON/OFF Switch on the unit by pressing PWR button (9). When system is on, press PWR button (9) again to turn off the unit.
OPERATION For detailed operations, please see below: BEEP ON/OFF When beep on, the beep in generated when every button is pressed. When beep off, the beep is disabled when press any button. Program power on volume level In this mode, you can set the desired volume level when the unit turns on. USA/EUR In this mode, you can select USA or European radio frequency spacing. - USA radio spacing is 200k for FM and 10k for AM. This is the default frequency spacing.
OPERATION • STATION STORING The preset buttons (14) can be used to store 6 stations in each band (FM 1, FM 2, FM 3 and AM1, AM2) for convenient access to your favorite stations. - Programming stations 1. Select the desired band, then tune in the station you want to store in memory. 2. Press and hold one of the preset buttons (14) for more than 2 seconds until the corresponding preset button number appears. Repeat steps 1. and 2. to program additional stations.
OPERATION and press MEM button (19) shortly, then “P-03” will appear. So track 10 will be secondly played. Repeat these operations and you can program CD tracks to your need. If you completed program setting, press PGM button (20) to play CD in programmed order. Note: Using Program function can only select up to 32 tracks to play in any order. When you have selected 32 tracks to be programmed. “FULL” will appear on the display.
OPERATION CD CHANGER OPERATION MP3 OPERATION • SELECT TRACKS Press button (16) or button (17) to move to the previous track or the following track. Track number shows on display. Hold and press button (16) or button (17) to fast reverse or fast forward. Disc play starts from when you release the button. • SELECT SONGS Single Step Selection: Press button (16) or button (17) to reverse or advance the previous song in single step.
OPERATION name, display will show (‘ ‘), then - Use the VOL / buttons (11&12) buttons to list all songs under this directory and select the title. - Press BAND/ENTER button (18) to confirm and start the play. - Repeat the above steps if the newly selected title is again a directory. 4. Searching From Current Directory Press MP3 button (13) four times, the unit searches file or directory from current directory by VOL / buttons (11&12). (D-DIR icon turns on if the name is directory).
OPERATION C. Notes on MP3 files: 1. The disc must be in the ISO9660 level 1 or level 2 format, or Joliet or Romeo in the expansion format. 2. When naming a MP3 file, be sure the file name extension is “.MP3”. 3. For a non-MP3 file, even though the file name extension is “.MP3”, the unit cannot recognize it. Note: A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 178 (D) x 50 (H) mm : : : : ± 10 dB ± 10 dB 4 x 50 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 60 dB : More than 50 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
88-C1802-15