MOBILE AUDIO SYSTEM Instruction Manual CD PLAYER WWW.PYLEAUDIO.
CONTENTS Installation 1 1. DIN FRONT-MOUNT (Method A) 1 2.
Installation Notes: - Choose the mounting location where the unit will not interfere with the normal driving function of the driver. - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. - Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
1. Frame 2. Release Frame Key Insert the release frame key into the groove at the right side of the frame, then prize out to remove the frame (You can also use the key to remove the frame from the left side.) 3. Release Unit Key After releasing the frame, insert the release unit keys supplied with the accessory into the grooves at both sides of the unit as shown in figure until they click. Pulling the keys makes it possible to remove the unit from the dashboard.
Precautions when handling 5. Do not expose the front panel to high 1. Do not drop the front panel. temperatures or direct sunlight in 2. Do not put pressure on the display or anywhere. control buttons when removing or 6. Keep away any volatile agents (e.g. installing the front panel. benzene, thinner, or insecticides) from 3. Do not touch the contacts on the front touching the surface of the front panel panel or on the main unit body. It may 7.
Operation General Operation Front panel : 2 9 18 19 4 10 1 17 14 15 13 3 11 12 6 When you remove the front panel : 21 4 20 5 7 8 16
SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except REL button (1) and button (4)) or inserting a disc to disc slot (18). When system is on, press button (2) to turn off the unit. SOUND ADJUSTMENT - Press VOL + / VOL - button (10) to adjust volume level. - Press SEL button ( 9 ) continually will changing in the following order: Press VOL +/ VOL - button (10) to adjust the desired sound quality.
TUNE BUTTON Rotate TUNE button (17) to get your desired broadcasting station. CD Operation SWITCHING TO CD MODE 1. If there is no CD disc inserted in the driver: Gently insert a CD with the printed side uppermost into the Disc Slot (18) until you feel some resistance. The disc is draw into the driver automatically. The CD playback begins. 2. If a CD disc is already inserted in the driver : Press MODE button (13) to switch to CD mode.
2. The unit cannot play a CD-R and CDRW that is not finalized. (Please refer to the manual of your CD-R/CD-RW recorder or CD-R/CD-RW software for more information on finalization process). 3. Depending on the recording status, conditions of the disc and the equipment used for the recording, some CD-Rs/CDRWs may not be played on this unit. (see *1) *1: To have more reliable play back, please see following recommendations: A. Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x. B.
Specification 1. GENERAL Power Supply Requirements DC 12 Volts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) Tone Controls - Bass (at 100 Hz) ±14 dB - Treble (at 10 kHz) ±14 dB Maximum Output Power 4x40 watts Current Drain 10 Ampere (max.) 2. CD PLAYER Signal to Noise Ratio > 55 dB Channel Separation > 40 dB Frequency Response 40Hz - 18 kHz 3. RADIO FM Frequency Coverage 87.5 - 107 . 9 MHz IF 10.
Troubleshooting Before go through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. No power - The car ignition switch is not on. ● If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. - The fuse is blown. ● Replace the fuse. Disc cannot be loaded or ejected - Presence of CD disc inside the player.
