R WNER'S MANUAL PLCD27 CD PLAYER C a r A u d i o H i f i S y s t e m
Band Band tuner Direct access tuning Power Volume play/pause eject clock loud release Radio wiring Speaker wiring Volume setting bass setting treble settting balance setting fader setting Install the unit Removing the unit Top scan repeat random stop 1
To prevent injur y of fire,take the following precautions: Insert the unit unitll it is firmly locked to the main unit, otherwise it may fall out of place when jolted When extending the ignition, memory back up or ground cable, use diameter of 0.75mm(AWG18) or more automotive grade cable to avoid wire deterioration or damage to the wire coating. To prevent short circuit, never put or leave any metallic object into the unit. If you smell or see smoke, turn off the power immediately and consult your dealer.
POWER ON/ OFF/VOLUME EJECT Volume PLAY/PAUSE RELEASE DSP TOP 1 SCAN 2 SELECT DSP REPEAT 3 RANDOM 4 STOP 5 VO L+ SELECT Decreasing CD BD PUSH ON/OFF VO Rotate the [VOL+]button L- Increasing volume EJECT VOL Rotate the [VOL-]button 6 CLK CLOCK Play/pause Play Press the [CD]button LCD display Pause Press again the [CD]button Power If a disc has already been loaded, CDIN would be shown on the display, press this button to start play disc even though the unit is in Radio mode.
Hour Eject Press [ Out ] button to adjust the hour. Minute Press the [ ]button ,if having adisc in the unit. The disc will be ejected out. Press [ ] button to adjust the minute. Quit clock set mode In If there no operation in 5 second, it will quit clock set mode. Press the [ ]button again, the disc will be load in. In beam mode, press the BD button can enter radio mode.
VOL+/- Speaker mode EJECT VOL VOLUME TREBLE BASS CD BD PUSH ON/OFF SELECT FADER TOP 1 DSP BALANCE SELECT In press mode, VOL is sel function SCAN 2 REPEAT 3 SCAN TOP RANDOM 4 STOP 5 6 CLK RANDOM REPEAT STOP Treble set mode Volume set mode Press SEL button third, display shows TRE ,then rotate the volume + button to adjust treble level up. Rotate the volume - buttonto adjust treble level down.
Top Scan Press [TOP]button Press [SCN]button Select the first track directly In CD mode,press this button, the first track will play. Press this button once for TRACK INTRODUCTION,the first ten seconds of each track on the disc will paly. To confirm the track number. Press it again while playing on the desired track. SCAN will appear on the display.Press it again to stop it.
SEEK- SEEK+ Tune In radio mode: EJECT manual tuning: VOL PUSH ON/OFF SELECT TOP 1 DSP SCAN 2 REPEAT 3 RANDOM 4 STOP 5 PRESET MEMORY 1-6 6 short press Short press CD BD button it can select higher frequency station. can select lower frequency station. Auto loading tuning: CLK the long press button it can automatically select higher frequency station. And the long press it can automatically select lower frequency station.
Loading and replacing the batter y Use one lithium battery(CR2025) insert the batteries with the +and - poles aligned properly. Following the illustration inside the case. APS LOUD CLK STOP Pull out MONO TOP Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. RPT Do not set the remote on hot places such as above the dashboard. SCAN Basic operation RDM Tur ning ON the power Press the [ ]button.
Volume Exter nal view ........ Number of items Exter nal view ........ Number of items Increasing volume Press the [+]loud VOL Increasing volume Press the [-]low VOL 1 ............ 1 5 ............ 1 2 ............ 1 6 ............ 1 3 ............ 1 7 ............ 1 ............2 8 Play/pause Play Press the [ ]button Pause Press the [ ] button again APS LOUD CLK STOP MONO TOP RPT 4 Radio control SCAN RDM ............
Follow this easy wiring diagram in order to enable you to install the new or existing RADIO and SPEAKER wring system. Be sure the unit is connected to a 12 volts battery with negative ground. Good ground connections eliminate most electrical noise problem and require tight with the metal vehicle chassis. remove plastic, paint or dust for good electrical contact.
B efore installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. When your system is operated properly,(preferably with the car engine running), follow the instructions for permanent installation of your system. 3)Support strap (supplied) INSTALL THE UNIT 1)Install half sleeve, can be with or without adapter. It will fit better with adapter.
Specifications subject to change without notice. CD PLAYER GENERAL Signal/Noise radio......................................................70dB Frequency response..............................20Hz-20KHz(+3dB) Channel separation..................................................>45dB Dual D/A converter.......................................................16Bit Operating power.....................................12 Volts DC,negative ground %10THD output wiring.........................
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. ?No/Poor sound on one or more speakers Speakers or speaker wiring or volume, Balance and Fader setting Check the speaker wiring and test the speakers all in good condition check the setting of volume, Balance and Fader controls. ?The power does not tur n ON. The fuse has blown.
CD C a r PLAYER A u d i o H i f i S y s t e m
