R CD/MP3PLAYER......
Play/pause Scan Repeat Shf Radio wiring Speaker wiring Install the unit Removing the unit Band Band tuner Direct access tuning Power Volume Eject Mode Loud Dsp Clock Release Loading and Replacing the battery Basic operation Volume setting Bass setting Treble settting Balance setting Fader setting 1
To prevent injur y or fire,take the following precautions: Insert the unit unt i l it is firmly locked to the main unit, otherwise it may fall out of place when jolted When extending the ignition, memory back up or ground cable, use diameter of 0.75mm(AWG18) or more automotive grade cable to avoid wire deterioration or damage to the wire coating. To prevent short circuit, never put or leave any metallic object into the unit. If you smell or see smoke, turn off the power immediately and consult your dealer.
Follow this easy wiring diagram in order to enable you to install the new or existing RADIO and SPEAKER wring system. Be sure the unit is connected to a 12 volts battery with negative ground. Good ground connections eliminate most electrical noise problem and require tight with the metal vehicle chassis. remove plastic, paint or dust for good electrical contact.
B efore installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. When your system is operated properly,(preferably with the car engine running), follow the instructions for permanent installation of your system. 3)Support strap (supplied) INSTALL THE UNIT 1)Install half sleeve, can be with or without adapter. It will fit better with adapter.
Volume POWER ON /OFF VOLUME EJECT Increasing volume SEL DSP SELECT RELEASE Rotate the [VOL-]button SEEK 1 SCN RPT SHF 2 3 4 BAND 5 DSP CLOCK LVO L+ VOL Decreasing VOL VO Rotate the [VOL+]button PWR SEL MODE 6 CLOCK MODE Eject LOC ST LOUD Out CH Press the [ LCD display ]button to eject the disc out of the unit . In Power Press the [ ]button again, to load the disc in. Tur ning ON the power Press the [PWR]button.
Hour MODE Press [ Selecting radio and play Minute Press the [MODE]key. Each time you press the key, it`ll switch between radio and CD position. (If mode with AUX IN,the function is below: press MD(MODE)to select: 1 If with DISC,press MD that is: AUX IN RADIO DISC Press [ RADIO ] button to set the minute. Quit clock set mode It will quit clock set mode If there is no operation in 5 seconds. AUX IN Dsp 2 If without DISC,press MD that is: AUX IN ] button to set the hour.
SELECT Speaker mode PWR VOLUME BASS TREBLE VOL SEL FADER SEEK DSP BALANCE VOLUME In press mode, VOL is sel function DSP 1 SCN RPT SHF 2 3 4 BAND 5 CLOCK MODE 6 SHF SCAN PLAY/PAUSE REPEAT Treble set mode Volume set mode L- VO 10 PR ES L+ VOL Press SEL button third, TRE 5 display shows TRE ,then rotate the volume + button to adjust treble level up. Rotate the volume - button to adjust treble level down.
Play/pause Shf Pause If with DISC in unit,Press the [ Press [SHF]button ]to pause music. Press [SHUF] button to play all the track in random order. SHF and playing song number will appear on the LCD. Press [SHUF]again will stop random playing. Play Press the [ ]button again ,then come back to DISC playing. Scan Press [SCN]button Press this button once for TRACK INTRODUCTION. The first 10 seconds of each track on the disc will play. And the track number shows on LCD.
Tuner In radio mode: PWR manual tuning: VOL SEEK- SEL short press Short press SEEK SEEK+ DSP 1 SCN RPT SHF 2 3 4 BAND 5 PRESET MEMORY 1-6 CLOCK button it can select higher frequency station. can select lower frequency station. MODE 6 Auto loading tuning: the long press button it can automatically select higher frequency station. And the long press it can automatically select lower frequency station.
Loading and replacing the batter y MODE MUTE PWR POWER SCAN MUTE -,_,+,0 MODE BAND STU7 ENTER 3 AS/PS ID3 AS/PS LOC LOCAL MONO MONO LOUD 1 PAUSE 2 ABC DEF GHI PAUSE SCAN RPT 5 4 SHUF DSP 6 JKL MNO PQR SHF DISC DN DISC UP DSP CHAR.SEL RO/SN VWX8 SHIFT YZ9 - SPACE + Use one lithium battery(CR2025) insert the batteries with the +and - poles aligned properly. Following the illustration inside the case. BAND/LOUD REPEAT VOL+/CHAR.
ID3 Exter nal view ........ Number of items Press ID3 on remote or Panel enter ID3 selection. one press ID3 enter ID3 file selection mode, F will be indicated on LCD. To read in your desired song name by pressing remote - buttons, then press confirmed the song playing. EXAMPLE: to read in " I LOVE YOU" In the read in mode: press button three times read I, press turn to next word,press three times read L,press three times read O and so on...
Specifications subject to change without notice. CD PLAYER GENERAL Signal/Noise radio......................................................70dB Frequency response..............................20Hz-20KHz(+3dB) Channel separation..................................................>45dB Dual D/A converter.......................................................16Bit Operating power.....................................12 Volts DC,negative ground %10THD output wiring.........................
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. ?No/Poor sound on one or more speakers Speakers or speaker wiring or volume, Balance and Fader setting Check the speaker wiring and test the speakers all in good condition check the setting of volume, Balance and Fader controls. ?The power does not tur n ON. The fuse has blown.
CD/MP3 PLAYER AM/FM RECEIVER WITH ESP FOR CD 40S,MP3 70-120S C a r A u d i o H i f i S y s t e m
