PLD70BT OWNER'S MANUAL Mobile Video System Motorized Slide Down and Detachable Panel 7 Inch Wide Color Touch Screen TFT Car DVD/MP4/VCD/CD/MP3 Player Front panel USB port and AUX input Built in AM/FM Tuner and RDS Bluetooth A2DP & AVRCP SD Card Slot in the panel
Contents Precautions .....................................2 Selecting Subtitles ..........................27 Safety Information......................... 3 Selecting multi-angle views .............. 27 Disc Notes .................................... 4 Title menu function .......................... 27 Installation .................................... 5 Setup .............................................28 Detaching the control panel .............. 7 General Setup ................................
Precautions THANK YOU FOR PURCHASING THIS CAR DVD PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Disc Notes Disc formats supported by this player DVD Audio and Video Disc size 12 cm VCD Audio and Video Disc size 12 cm CD Audio Disc size 12 cm MP3 Audio Disc size 12 cm Discs which cannot be played with this player DVD-RAM CDV CDG Handling and Cleaning Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging.
Installation NOTES: 1. Choose the mounting location where the unit will not interfere with the normal driving function of the driver. 2. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. 3. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. 4.
Installation 3. Remove the PLASTIC COVER of the both sides away PLASTIC COVER 4. Insert the two KEY PLAT into the grooves at both sides of the unit as shown in figure until they click . KEY PLATE 5. Pulling the levers makes it possible to remove the unit from the dashboard .
Installation How To Remove And Install The Front Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching The Front Panel Before detaching the control panel, be sure to turn off the power. 1). Press the “REL” release button and the left hand side of front panel will release. RELEASE BUTTON 2). Pull-off the front panel and keep the front panel into the case .
Panel Angle Adjustment CHANGING THE CONTROL PANEL ANGLE When you want to change the viewing angle of the operating unit to play, you can touch the section on touch screen (or press the button on the front panel) repeatedly to select the desired angle as follows: ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGEL 4 - ANGLE 1 . ANGLE 1 ANGLE 2 ANGLE 4 ANGLE 3 Caution: Do not insert your finger behind the control panel.
Electric Connection WIRING CONNECTION MAIN UNIT ISO CONNECTOR WHITE BROWN RADIO ANTENNA JACK (B+)12V REAR CAMERA SWITCH (B-)PARKING BRAKE YELLOW REAR CAMERA INPUT RCA CABLE FUSE IGNITION SWITCH(B+) MEMORY YELLOW BACK-UP(B+) GROUND(B-) REAR RCA OUTPUT CABLE RED BLACK GREY SUBWOOFER VIDEO OUT 2 YELLOW COAXIAL OUT BROWN RCH RED LCH WHITE CHOKE BOX FRONT RCA OUTPUT CABLE FRONT RCA RED R VIDEO OUT 1 YELLOW FRONT RCA WHITE L (FOR RCA LINE OUT VERSION ONLY) AUTO ANTENNA FUSE BLUE FRONT Lch SPK.
Remote Control 15 16 3 17 7 2 5 19 20 13 21 6 22 1 23 14 9 18 12 11 26 10 4 24 8 Ref # Button 1 2 3 4 5 25 Function Press it briefly to view the clock time , Press again to return to normal display mode . Press longer to set the time . Press it to use the Bluetooth function , refer to the page 33 . PAIR/ Press once to pause playback. Press PLAY/PAUSE to resume STOP playback. Please note: if you press STOP twice, playback will start at the beginning of the disc.
Remote Control Ref # Button 8 GOTO 9 / 10 SEL 11 VOL+/- 12 / / / 13 14 15 Function Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. In Bluetooth menu, it serves as the asterisk button on your mobile handset. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button 23 ENTER This button is used to confirm selections and settings within many of the menus in the OSD system. 24 0-9 25 +10/ This button is used with the other number buttons for use with two-digit number entries. In Bluetooth menu, it serves as the hash button on your mobile handset.
Control Panel Key Functions Touch Panel MODE PAIR VOLUME- MUTE ON REDIAL DIAL VOLUME+ SEL Touch Screen Key : Changing the viewing angle of the operating unit MODE MUTE ON REDIAL VOLUME- Operating mode selection Redialling Decrease the volume level To switch of the sound SEL Select the menu of the Picture/Sound Loading and ejecting the DVD/CD VOLUME+ Increase the volume level PAIR Registering devices with one another DIAL Calling up the Bluetooth menu Next menu -13-
Control Panel Unit Keys : 11 10 9 8 7 6 5 4 12 13 3 2 1 1 AUX Input JACK For information about connecting a AUX device, please see page 25 . 2 IR SENSOR 3 VOL+/ VOL- KNOB In normal mode, this knob is used to increase or decrease the volume. It is also used as an UP/DOWN knob when audio or video settings are being adjusted when accessed using the SELECT button. 4 (POWER On/Off )/MODE BUTTON Press this button to switch the device on. WELCOME appears in the display.
Control Panel 6 REL BUTTON Press this button to release the front panel for removal . Refer to see page 7. 7 8 /CH 1-6 (RADIO PRESET) BUTTON A) In Disc Playback Mode Press this button to pause playback, press it again to resume playback. B) In Radio Mode Press this button repeatedly to preset station. With this system a total of 30 stations can be stored in the memory . Each band store up to six preset stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2 (MW2) band.
Basic Operation POWER On/Off Mute Function Press it to switch the device ON, press and hold about 2 seconds to switch the device OFF. MUTE ON Touch “MUTE ON” range, it will mute the sound but the disc continues playing . Touch it again to resume . Ejecting The Disc Use your finger to touch the range on touch screen , the control panel of the unit will swing downwards . Then you can insert the disc or eject the disc .
Basic Operation Rear View Camera TFT Monitor Adjustment During DISC playback, use your finger to touch briefly the SEL section on the screen (or press SEL button on front panel ) to access the Picture mode selection menu, by repeatedly touch the SEL section, and then touch the VOL+/(or rotate the VOL+/-) to adjust the selected mode . (The corresponding value will show on the monitor ) SEL Volume Bass Treble Balance Bluetooth Buzzer Fade Tint Contrast Bright When connecting the rear view camera.
Basic Operation Balance: R 0-10 to L 0-10 . Adjust sound balance between left and right speakers by using VOL + / - . Fader: F 0 - 10 to R 0 -10 . Adjust sound balance between front and rear speakers by using VOL + / VOL - . Setting Audio Modes Touch the screen the DSP range (or press the EQ button on the remote control ) to select one of the preset sound modes . (Rock/Pop/Jazz/Classic/Flat) .
Radio Operation Listening to the Radio select the band , the message will show in turn : Switching To Radio Mode FM1 Touch the screen of “MODE” range (or press the MOD button on the front panel ) repeatedly to select the RADIO mode. the following information will appears as below: FM2 FM3 MODE AM2(MW2) AM1(MW1) Start Searching For a Station Manual Search FLAT 12:06 ST FM1 TA NO-DISC DX 87.60 MHZ MODE 1 2 MUTE ON 3 VOLUME- 4 SEL FLAT 5 6 VOLUME+ 12:06 NO-DISC ST FM1 AF DX 87.
Radio Operation e.g. FM1, for the stronger signal level until the search cycle has finished . The six strongest stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set . Storing Stations In Memory With this system, a total of 30 stations can be stored in the memory of six buttons. Each band stores up to six preset stations. The stations might be FM1, FM2, FM3, AM1(MW1), and AM2(MW2) band.
Radio Operation When the TA function is switched on , the FM traffic automatically interrupt CD operation(the word TRAFFIC appears in the display). The volume level is increased to the minimum value for the transmission of traffic announcements. Note : the status of the AF function is shown by an AF symbol in the display. If the AF symbol appears in the display, the AF function is switched on and RDS transmission date is being received .
DISC Operation Basic Operation Switching the DVD mode During DISC playback, you can touch the screen to display the following: Touch the screen of “MODE” range (or press MOD button on the front panel ) to select the DISC mode, it display like following : FLAT 12: 16 DISC-IN DVD FLAT 1-0:00:16 MODE 12: 16 DISC-IN DVD MUTE ON 1-0:00:16 MODE VOLUME- VOLUME+ SEL VOLUME- FLAT MUTE ON SEL VOLUME+ 12: 16 Function setup (different the source the display is different) DISC-IN DVD 1-0:00:16
DISC Operation Selecting The Play Modes Skipping Track During DISC playback, Touch the / section on the touch screen to skip to next/back one track. During the Disc playback, touch the touch screen, it will display the following as below : FLAT 12: 16 DISC-IN DVD Note : 1. In DVD mode, touch the section continually twice to back one track . 2. For some VCD2.0 disc (PBC-playback control), above these buttons may be unavailable .
DISC Operation Each playing, the order is different . (Depend on the disc used for VCD). Touch it again to cancel this function . Note : in random mode, the button is not available . DISC Search (GOTO) FLAT DISC-IN DVD 3). INT Function RANDOM REPEAT S-WOOFER TA INTRO AF DSP CLK LUD GOTO Touch to select FLAT 12:16 DISC-IN DVD 1-0:00:16 GOTO FOR VCD : Touch the screen of the “INTRO” section (or long er press the 3/INT button on the the remote control ).
DISC Operation Note: Touch and hold the / section on the touch screen , you can select the title or chapter of DVD . (Only for the DVD with title /chapter.) FLAT 12: 16 DISC-IN AUX IN TA AUX Operation CLK On the front panel of this unit, there is an AUX IN jack, follow the diagram below t o connect analogue replay devices. Use this jack to replay sound of other replay equipment such as DVD players, computers, etc. Via the loudspeakers. AUX IN JACK FRONT PANEL DOM RCH IN (red) LCH IN (white) 1).
DISC Operation ON-SCREEN DISPLAY FUNCTION OSD During playback, touch the screen the OSD section (or press the OSD on the remote), it will display the following as below : 2.Example for VCD/SVCD/CD: A.Touch or Press OSD for first time: SINGLE ELAPSED TRACK 01/16 0:00:56 1. DVD: A.Touch or Press OSD for first time: B.
DISC Special Functions DVD/VCD Special Function FLAT For VCD/CD: during playback, touch the AUDIO section of the touch screen or Press AUDIO on the remote . It is possible to switch the sound between monaural and stereo sound. 12: 16 DISC-IN DVD 1-0:00:16 PAIR DIAL AUDIO REDIAL SUBTITLE SETUP MONO LEFT MONO RIGHT MIX-MONO STEREO ZOOM TITLE 3. Multi-Angle Function (for DVD Only) Touch to select 1. Multi-subtitle Language Function (for DVD Only) During DVD playback.
SETUP GENERAL SETUP --- GENERAL PAGE --DOLBY DOLBY -----General setup page---- -----General setup page---TV Display LB TV Display Normal/PS Angle Mark ON Angle Mark Normal/LB OSD Lang ENG OSD Lang Wide Spdif Output SPDIF/RAW Spdif Output Captions ON Captions Screen Saver ON Screen Saver Last Memory ON Last Memory Set TV Display Mode Go To General Setup Page 1. Press SETUP button on the remote control . 2.The SETUP menu is displayed. 3.
SETUP DOLBY DOLBY -----General setup page---- -----General setup page---- TV Display TV Display Angle Mark ON Angle Mark OSD Lang OFF Osd Lang Spdif Output Spdif Output Captions Captions Screen Saver Screen Saver Last Memory Last Memory SPDIF OFF SPDIF/RAW SPDIF/PCM Set Angle Mark Setup SPDIF 2. ANGLE MARK DISPLAY SETUP If it is set to ON, when the multi-angle DVD disc is playing, (the angle mark) will appears on the screen; if is set to OFF, the mark will not appear. 4.
SETUP SPEAKER SETUP DOLBY --- SPEAKER SETUP PAGE --DOLBY -----General setup page---TV Display -----Speaker Setup Page---- Angle Mark OSDLang DOWNMIX Spdif Output LT/RT STEREO Captions Screen Saver ON Last Memory OFF Screen Saver 6.SCR SAVER SETUP Select the SCR SAVER output ON/OFF. DOLBY Set Downmix Mode This is to activate the audio output from DOLBY AC3 5.1 DOWNMIX to 2 channel mode. Select the preferred SPEAKER connection by using the cursor buttons.
SETUP PREFERENCES SETUP --- PREFERENCES PAGE --- DOLBY DOLBY -----Preference Page--------Preference Page---- TV Type English TV Type PAL Audio French Audio AUTO Subtitle German Subtitle NTSC Disc Menu Spanish Disc Menu Parental Italian Parental Password Portuguese Password Default Russian OFF Default Set TV standard Preferred Subtitle Language 1.TV TYPE SETUP This player can play discs recorded in either PAL or NTSC format.Select NTSC format, when you connected to NTSC TV.
SETUP DOLBY DOLBY -----Preference Page---- -----Preference Page---- TV Type 1KID SAF TV Type Audio 2G Audio 3PG Subtitle 4PG13 Disc Menu 5PGR Parental Subtitle Disc Menu Parental Password Default 6R Password 7NC 17 Default RESET 8 ADULT OFF Set Parental Control Load Fcatory Setting 7.DEFAULTS Select reset to become factory initial setting. 5.PARENTAL Select suitable parental guidance by the cursor buttons and conformed by pressing ENTER button.
Bluetooth Operation Bluetooth Car Kit User Manual 1. “Pair”To Your Bluetooth Phone Prior to using the Car Kit for the fist time, you must pair it with a Bluetooth-enabled mobile handset. The following steps describes pairing the instruction for a typical Bluetoothenabled mobile handset. Touch the touch screen , the touch operation menu will display.
Bluetooth Operation Adjust the Volume DIAL ” section , Touch the screen of “ the message will display as below : During conversation in progress, tune the Volume switch until you reach the desired volume level. DIAL NUMBERS 1 2 3 4 5 6 7 8 9 0 Play BT music touch to dial CLEAR In Bluetooth menu, touch the screen of “MODE” range to select the “BT MUSIC” , you can play the BT MUSIC from your mobile handset.
Other Main Operation USB Operation Changing From DISC to USB Playback Modes If the disc present in the player is an MP3 disc, touch section on screen or press the STOP on remote once then touch or press the GOTO to USB playback. If the disc present in the player is an DVD or VCD or CD disc, touch on the screen or press STOP twice on the remote then touch GOTO section on the screen or press the GOTO button on the remote to USB playback.
Other Main Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . Inserting and removing a SD or MMC card on the front panel of unit . Inserting the SD or MMC card . Label side facing backward Insert the memory card into slot with label side facing backward . Press in till heard a “CLICK” . Removing the SD or MMC card . Remove the memory card .
Other Main Operation MP3/WMA/JPEG/MPEG4 DISC PLAY When you insert a disc which contains MP3, WMA or JPEG files, the different file types are detected, and a list of the files are produced, as shown in the diagram below. 5 4 3 00:56 2 003/112 1 04:07 Mp3 K Mp3 woman 1 Mp3 new ton 6 Repeat one P ....... ....... 1 Current track(file)(highlighted bar) 2 Current track (file) number/total number of tracks(files) in the current folder.
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.