User's Manual

ManualsBrandsPYLE Audio ManualsCar video systemsPLRTD155

《23》

15.4" FLIP-DOWN MONITOR WITH BUILT-IN

DVD,WIRELESS FM MODULATOR & TV

PLRTD155

FEATURES

MONITOR SECTION

!HI RES TFT-LCD MONITOR 15.4” WIDE SCREEN

!HIGH RESOLUTION : 1280(H) x 800 (V)

!BRIGHTNESS : 450 CD/SQ.M

!CONTRAST RATIO : 500 : 1

!VIEWING ANGLE : 140° (LEFT/RIGHT ) 120° (TOP ) 120°( DOWN )

!OVERHEAD CONSOLE WITH TWIN DOME LIGHTS WITH LED

!IR TRANSMITTER READY FOR IR WIRELESS HEADPHONE

!BUILT-IN OSD DIGITAL FM MODUALTOR

!CREDIT CARD SIZE REMOTE CONTROL

!ON SCREEN MENU SYSTEM

!FRONT PUSHBUTTONS CONTROLS

!AUDIO / VIDEO INPUT

!MULTI SYSTEM: NTSC & PAL , SECAM AUTO SWITCH ABLE

DVD SECTION

!S LOT-IN TYPE DVD PLAYER

!P LAY BACK DISC: DVD-VIDEO, VIDEO –CD, SVCD, CD-DA, CD-RW & MP3

!1 0 BIT DAC VIDEO ENCORDER

!5 00 LINES HORIZONTAL RESOLUTIONS

!P ROLOGIC DECODER

!M PEG-2 TWO CHANNEL ANALOG OUT

!2 4-BIT 96KHZ DAC

!F REQUENCY RESPONSE: 20 Hz to 20KHz

!GENERAL SPECIFICATIONS

!POWER REQUIREMENT: 12 V DC

!BUILT-IN TV TUNER.

!SINGLE POWER CABLE WITH NOISE FILTER CIRCUIT

!DIN INTERFACE CABLE WITH RCA JACKS FOR AUDIO AND VIDEO

CONNECTIONS

ACCESSORIES

* Overhead Console Mounting Bracket

* Remote Control with Batteries

* Power Connection Cable

* User's Manual

Antenna

Summary of content (12 pages)

PAGE 1
FEATURES MONITOR SECTION !HI RES TFT-LCD MONITOR 15.4” WIDE SCREEN !HIGH RESOLUTION : 1280(H) x 800 (V) !BRIGHTNESS : 450 CD/SQ.
PAGE 2
TROUBLE SHOOTING Table of Contents 1. Table of Contents ------------------------------------------------------1 2. Warning -----------------------------------------------------------------1 3. Usage Notice -----------------------------------------------------------2 4. Where to Install --------------------------------------------------------3 5. Operating the Monitor-------------------------------------------------4 6. Installation your Monitor --------------------------------------------- 5 7.
PAGE 3
c onnection Diagram Usage Notice Refer to the connection diagram for the proper connections. You can make connections shown as below. Please ask a qualified technician for the other connections. “F” CONNECTOR 2 1 DVD PLAYER 《21》 Follow all warnings, precautions and maintenance as recommended in this user's manual to maximize the life of your LCD monitor To avoid the damage of the LCD monitor and risk of electronic shock, do not permeate the LCD monitor with water or any drink.
PAGE 4
Installation TV SYSTEM AND AUDIO MODE OF PRIMARY Where to Install Before installing this unit, please check your local traffic rules and regulations. Follow the diagram below to install this unit in a suitable position in your car. " /": Show this country has no sound to output the system Other have not listed the country and above catalogs system same also in this machine support scope.
PAGE 5
7-3 CH ERASE Installation your Monitor CH ERASE CH1 ↑↓ADJUST EXIT : SETUP OK:ENTER It can to use CH+/CH- key makes the choice, and press ENTER deletes the selected one. And the next channel will fill a vacant position. This primitive channel will not exist to this TV BOX In memory. If wants to restore this primitive channel, then recreates "AUTO FULL SCAN" will restore the channel.
PAGE 6
Operating the Monitor 7.CH EDIT CH EDIT Opening the Monitor CH HIDDEN CH SWAP CH ERASE 1. Press the monitor release button to lower the LCD screen. 2. Lower the monitor until is fixed 90 from the monitor base unit for viewing (Refer to the following figure.) ↑↓ADJUST EXIT : SETUP OK:ENTER When the indicator is on the CH EDIT, press ENTER on the unit/remote to display and select the item you want to change by CH+/CH7-1 CH HIDDEN CH HIDDEN ↑↓ADJUST EXIT : SETUP OK:ENTER Closing Monitor 1.
PAGE 7
4.AUTO FULL SCAN Setting Up The Dome Lamps AUTO FULL SCAN PRESS ENTER TO START ↑↓ADJUST EXIT : SETUP OK:ENTER When the indicator is on the AUTO FULL SCAN, press ENTER on the unit/remote to display this picture and auto full scan channels by pressing ENTER *Operating the dome Lamps 1. There are three function buttons for the Dome lamps operation: OFF, DOOR, and ON. (Refer to the following figure) A. OFF: To turn off the lamps. B. DOOR: To make the lamps turned on only when car doors are opened. C.
PAGE 8
2-1.COLOR SYSTEM Monitor Selection COLOR SYSTEM NTSC ↑↓ADJUST EXIT : SETUP OK:ENTER On the picture of TV SYSTEM, when the indicator is on the COLOR SYSTEM, press ENTER on the remote to display this picture and change the mode of NTSC, PAL,SECAM,FM by CH+/CH2-2.AUDIO SYSTEM POWER AUDIO SYSTEM B/G MENU UP DOWN ↑↓ADJUST EXIT : SETUP OK:ENTER MUTE * Power: You may also turn on or off the monitor by this "Power" button.
PAGE 9
DISPLAY * OSD Menus in A/V Source A. Source Selection Menu 1.MAIN MENU MAIN MENU SOURCE CVBS.1 = NTSC H. SYNC = +15.7K Hz V. SYNC = +60.0 Hz Use remote control “SETUP” button to enter/exit menu and use “enter” button to confirm the selection. AUTO DETECT 1 2 BRIGHTNESS CONTRAST COLOR HUE SOURCE AUDIO RECALL MAIN MENU TV SYSTEM ANT SOURCE AUTO FULL SCAN VIDEO 1 VIDEO 2 RETURN B.
PAGE 10
DVD SECTION To operate DVD by pressing the buttons on up panel: 6 5 4 3 2 1 1. POWER: Press "POWER" ON, insert the disc with printed side face up into the disc slot, the player starts playback automatically. 2. EJECT: Press"EJECT" to eject the disc. 3. PLAY/PAUSE: Press "PAUSE" to stop playing temporary, press it again to resume playback. 4. STOP: Press "STOP" to stop the unit playback. When press "PLAY", it will resume playback to the last scene you were watching.
PAGE 11
TV TUNER SECTION Remote Control Use remote control “SETUP” button to enter/exit menu and use “enter” button to confirm the selection . 1. POWER: Power for ON or OFF 2. DVD MENU: Enter to menu for DVD 3. OPEN: Open or close disc tray 4. SOURCE: Switch input source button 2 4 3 (TV, DVD) 5. LANGUAGE: Choose different output language 6. SUBTITLE: Select or cancel subtitles 1 3 2 7. TITLE: Display the TITLE menu stored in 6 5 4 the DVD disc. 18 8.
PAGE 12
FM MODULATOR SECTION 26. VOL+: Volume up the monitor 27. VOL-: Volume down the Monitor 28. MUTE: Shut the sound OFF 29. MENU: Enter monitor OSD Menu 30. EXIT: Exit OSD menu select 31. FORMAT: Switch NTSC/PAL 32. V-Chip(Option): Enter V-Chip setup to select a rating level. 33. C.C (Option): Close caption 34. CH+: Adjust channel up 35. CH-: Adjust channel down Appendix Changing the New Battery in Remote Control 1. Push the battery case button to wards the right.