MOTORIZED 7” WIDE TFT LCD MONITOR WITH COLOR TV MODEL NO. : PLTV7.
ANY CHANGES OR MODIFICATIONS IN CONSTRUCTION OF THIS UNIT DEVICE WHICH IS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
CONTENTS WARNING CAUTION UNIT 1. MONITOR 2. REMOTE CONTROL 3. REMOTE CONTROL BATTERY BASIC OPERATION 1. POWER ON/OFF 2. OPENING THE MONITOR 3. CLOSING THE MONITOR 4. ADJUSTING TILT POSITION 5. ADJUSTING MOVE POSITION 6. ADJUSTING LEFT/RIGHT VIEWING POSITION 7. SELECTING MODE 8. AUDIO MUTE 9. ADJUSTING VIDEO PICTURE MODE (ASPECT) 10. SELECTING THE MENU FUNCTION 1. FM TRANSMITTER CONTROL 2. TILT POSITION CONTROL 3. MOVE POSITION CONTROL CONTROL 1. NAVIGATION AUDIO 2. WATCHING NAVIGATION 3.
WATCHING TV 1. MENU CONTROL 2. CHANNEL CONTROL 3. FINE TUNING CONTROL 4. AUTO MEMORY 5.
WARNING The exclamation mark in triangle and WARNING mark are intended to alert the user to the important operating instructions. Wrong operations will result in severe injury to the unit. DO NOT WATCH MONITOR WHILE DRIVING Watching the video while driving may interrupt driving and may cause an accident. DO NOT OPERATE ANY FUNCTION THAT TAKE YOUR ATTENTION AWAY FROM DRIVING YOUR VEHICLE Operation of some functions for this unit is very complicated.
CAUTION DO NOT RAISE THE VOLUME EXCESSIVELY Keep the volume at a specific level which you can still hear outside noise while driving . Keeping the volume loud may cause an accident. DO NOT USE THIS EQUIPMENT OUTSIDE THE VEHICLE Do not use this equipment for purpose other than those listed for a vehicle. Failure to do so may result in an electric shock or an injury. HOW TO USE THE BATTERIES Do not mix new batteries with old batteries and do not replace with other than specified batteries.
UNIT 1. MONITOR 4 5 5 4 4 1 2 3 1. POWER ON/OFF / MODE BUTTON 2. OPEN/CLOSE BUTTON 3. TILT UP/DOWN BUTTON 4. MENU BUTTON 5.
2. REMOTE CONTROL 1. POWER ON/OFF BUTTON 2. TILT UP/DOWN BUTTON 3. OPEN/CLOSE BUTTON 4. MODE SELECTION BUTTON 5. SOUND MUTE BUTTON 6. NAVIGATION BUTTON 7. ASPECT SELECTION BUTTON 8. SEARCH UP/DOWN BUTTON 9. VOL ◀ / ▶: TILT UP/DOWN BUTTON 10. MENU BUTTON 11. MANUAL SEARCH BUTTON 12. AUTO SEARCH/ AUTO MEMORY BUTTON 13. BAND SELECTION BUTTON 14. NUMERIC BUTTONS 3. REMOTE CONTROL BATTERY - Do not insert battery in the wrong direction.
BASIC OPERATION 1. POWER ON/OFF 1) POWER ON (1) Press the POWER button on the unit or on the remote control to turn the power on. But the monitor will not be opened and you can listen to the sound of this unit. (2) You can also turn the power on by pressing the OPEN/CLOSE button. The power will be on and the monitor will be opened. 2) POWER OFF (1) Press the POWER button on the unit or on the remote control again to turn the power off.
3. CLOSING THE MONITOR 1) Press OPEN/CLOSE button on the unit or on the remote control. The monitor will be closed. 2) If it is not closed, hold left and right upper side of the monitor and make the monitor parallel with the unit as the picture. And press OPEN/CLOSE button to close the monitor. NOTE 1) If the monitor is not parallel to the front of the unit, the monitor will not be closed. 2) If OPEN/CLOSE button is pressed while the unit is powered on, the monitor will be closed but the power is still on.
5. ADJUSTING MOVE POSITION 1) Press MENU button to show FUNCTION on the screen. 2) Press SEARCH ▲/▼ button to select MOVE. 3) Press VOLUME ▶button to move the unit one step forward(50mm). The menu will show the position at 1, 2, 3. Press VOLUME ◀button to move the unit one step backward(50mm). The menu will show the position at 2, 1, 0. 6. ADJUSTING LEFT/RIGHT VIEWING POSITION The monitor’s left/right position can be adjusted for easier viewing by hand as the picture below.
7. SELECTING MODE Press MODE button to select the desired mode. Each time you press this button, the mode changes as follows. AV1 -> AV2 ->AV3 ->TV NOTE AV3 has only video input. 8. AUDIO MUTE Press MUTE button to make the sound mute. Press MUTE button again to return to the previous audio level, or if you press VOLUME ◀ or ▶ button, the volume will be adjusted and the sound will be on. 9.
follows. 1) Press MENU button repeatedly until CONTROL MENU is selected. 2) Press SEARCH ▲/▼ button to select SCREEN. 3) Press VOLUME ▶ or ◀ button to select the desired picture mode. 10. SELECTING THE MENU You can select the menu to make this unit or AV sources connected to this unit operate in the best conditions. 1) Press MENU button to select the desired menu. Each time you press MENU button, the menu changes as follows.
FUNCTION 1. FM TRANSMITTER CONTROL This is to listen to the sound of AV sources connected to this unit with the car speakers. If you set the FM frequency of the FM transmitter in the following way and you have the FM Radio unit in your car, you can listen to the sound of AV sources of this unit. 1) Press MENU button to show FUNCTION menu on the screen. It will show the following menu. 2) Press SEARCH ▲/▼ button to select FM TRANS. 3) Press VOLUME ▶ or ◀ button to select ON/OFF.
2. TILT POSITION CONTROL 1) Press MENU button to show FUNCTION on the screen. 2) Press SEARCH ▲/▼ button to select TILT POSITION. 3) Press VOLUME ▶button to swing the LCD panel one step backward. Press VOLUME ◀button to swing the LCD panel one step forward. The TILT position is +2, +1, 0, -1, -2. 3. MOVE POSITION CONTROL 1) Press MENU button to show FUNCTION on the screen. 2) Press SEARCH ▲/▼ buttons to select MOVE POSITION. 3) Press VOLUME ▶button to move the unit one step forward(50mm).
CONTROL 1. NAVIGATION AUDIO (※ In case, you use an optional compatible Navigation System) When a navigation system is connected to this unit, you can use the navigation system properly after you adjust the navigation audio control.
2. WATCHING NAVIGATION Press NAVI button on the remote control in order to watch the navigation. NOTE When the rear view camera is connected to this unit and you put the gear lever to R(Reverse Gear), the rear view will be displayed on the screen even if the monitor is on Navigation mode. 3. SETTING THE CAMERA IN When a rear view camera is connected to this unit, you can adjust CAMERA IN CONTROL.
4. WATCHING THE REAR VIEW Put the gear lever to R(Reverse) on any mode. The monitor will show the rear view camera picture. 5. WIRING CONNECTION Connect orange color connection wire with a “REVERSE GEAR” sticker to a switched power output terminal of the R (Reverse) gear. See BASIC CONNECTION Part. NOTE If you select AV mode connected to the rear view Camera with MODE button, the monitor does not show the rear view camera picture. The monitor will show only the WARNING picture. 6.
PICTURE 1. CONTRAST CONTROL 1) Press MENU button to show PICTURE on the screen. 2) Press SEARCH ▲/▼ button to select CONTRAST. 3) Press VOLUME ▶ or ◀ button to change the CONTRAST. VOLUME ▶ : CONTRAST level will be increased. VOLUME ◀ : CONTRAST level will be decreased. CONTRAST level is from 0 to 30. 2. BRIGHT CONTROL 1) Press MENU button to show PICTURE on the screen. 2) Press SEARCH ▲/▼ button to select BRIGHT. 3) Press VOLUME ▶ or ◀ button to change the BRIGHT.
3. COLOR CONTROL 1) Press MENU button to show PICTURE on the screen. 2) Press SEARCH ▲/▼ button to select COLOR. 3) Press VOLUME ▶ or ◀ button to change the COLOR. VOLUME ▶ : COLOR level will be increased and the COLOR will be richer. VOLUME ◀ : COLOR level will be decreased and the COLOR will be lighter. COLOR level is from 0 to 30. 4. TINT CONTROL 1) Press MENU button to show PICTURE on the screen. 2) Press SEARCH ▲/▼ button to select TINT. 3) Press VOLUME ▶ or ◀ button to change the TINT.
5. DIMMER CONTROL 1) Press MENU button to show PICTURE on the screen. 2) Press SEARCH ▲/▼ button to select DIMMER. 3) Press VOLUME ▶ or ◀ button to change the DIMMER ON or OFF. ON : When this unit is set to on. The brightness of this unit will be changed depending on the brightness of the environment. OFF : When you do not need the DIMMER.
WATCHING TV You cannot control this unit while driving for your safety. You should control this unit after you park your car in a safe place and pull the parking brake up. 1. MENU CONTROL 1) Press MENU button to show MENU on the screen on TV mode. 2) Each time you press MENU button, the MENU changes as follows.
3. FINE TUNING CONTROL 1) Press MENU button to show TUNING on the screen. 2) Press SEARCH ▲/▼ button to select FINE. 3) Press VOLUME ▶ or ◀ button to do the FINE TUNING. VOLUME ◀ : The center frequency level of the channel will be decreased. VOLUME ▶ : The center frequency level of the channel will be increased. FINE TUNING frequency range is from –32 to +32. 4. AUTO MEMORY 1) Press MENU button to show TUNING on the screen. 2) Press SEARCH ▲/▼ button to select AUTO MEMORY.
DELETE (A) Go to the memorized channel which you want to delete. (B) Press delete button on the remote control. The channel will be deleted.
WARNING SCREEN The monitor shows the following warning picture when the parking brake is not pulled or while driving to prevent traffic accident that may happen while watching the screen. The monitor shows the warning picture only and does not show any other picture, but you can enjoy the sound only.
INSTALLATION PRECAUTIONS Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. Use only the supplied mounting hardware for a safe and secure installation. MOUNTING ANGLE ADJUSTMENT Adjust the mounting angle to less than 20°.
BASIC CONNECTION NOTE 1. Be sure that the PARKING SENSOR WIRE must be grounded or opened. If it is connected to ACC(B+). The unit can be damaged. 2. Do not ground the POWER ANTENNA wire or REMOTE TURN ON wire. If it is grounded, the unit can be damaged.
CONNECTING TO AV SOURCES 28
SPECIFICATIONS General Power Supply DC 14.4V(11V-15V) Power Consumption 1.5A Operating Temperature -10 degree~ 60 degree Audio Input Sensitivity 1.0V/22K Ohm Audio Output Voltage 0.5V/1K Ohm Video Input Signal 1.0Vpp/75 Ohm Video Output Signal 1.0Vpp/75 Ohm Dimensions 178(W) x 25(H) x 160(D)mm Polarity Negative Ground only Fuses 2A(Back Up) 3A(ACC) Weight Net 1.5Kg Gross 2.
TROUBLE SHOOTING GENERAL Problem Power Cause Measure does Fuse is blown Replace with a fuse of the same amperage. not turn on. If the fuse blow again, consult installation (No sound is shop where you purchased it from. produced.) Incorrect wiring Consult installation shop where you purchased it from. Power it off and power it on again. If it is The Nothing not working, consult installation shop where happens when microprocessor are has malfunctioned you purchased it from.
The headlight of The display is made dark at night to the vehicle is lit. prevent the glare (When the headlight of the vehicle is lit in the daytime, the display gets dark). The color of The color is not Check that Color and Tint are adjusted the properly. display is adjusted light a adequately. or shade of color is not good . TV The image Bad gets unclear. receiving A radio wave may not reach sufficiently due condition. to obstruction of mountains or buildings.
