Any changes or modifications in construction of this device which is not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
Safety precaution WARNING For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving are prohibited by law in some countries. Also, while driving, keep the volume to a level at which external sounds can be heard. To prevent injury or fire, take the following precautions: Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted.
CONTENTS Safety Precaution (p4) About CDs (p5) Introduction (p6) 1. Region Number .......................................... 2. Control Parts .............................................. 2-1. With Display Closed ............................ 2-2. With Display Opened .......................... 3. Head unit Rear Panel ................................. 4. Battery ........................................................ 5. Remote Control key ...................................
Safety precaution The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis / case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. NOTE If you experience problems during installation, consult your PYLE dealer. If the unit fails to operate properly, press the Reset button.
Safety precaution Cleaning the Faceplate terminals If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. Cleaning the Unit If the front panel of this unit is stained, wipe it with a dry soft cloth such as s silicon cloth. If the front panel is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, and then wipe neutral detergent off. Applying spray cleaner directly to the unit may affect its mechanical parts.
About CDs Handling CDs Don t touch the recording surface of the CD. Removing CDs When removing CDs from this unit,pull them out horizontally. CDs that can t be used CDs that aren t round can t be used. CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. Don t stick tape etc. on the CD. Also, don t use a CD with tape stuck on it. CDs with coloring on the recording surface or that are dirty can t be used.
INTRODUCTION Notice. “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation 1. Region Number The region number of this Unit is labeled on the rear panel of the unit. Most DVD s are manufactured specifically for sale and use in a specific geographic region. A disc s Region Number must correspond to the Region Number of this Unit. If the Region Number of a disc is different from the Region Number of the this Unit, playback will not be possible.
INTRODUCTION WITH THE DISPLAY CLOSED Volume Up/Down Use this button to increase/decrease the volume. Tilt Use this button to adjust the angle of the TFT LCD panel in 3 steps and every time this button is pressed with being held for about 2 second or longer, the TFT LCD panel moves backward with 2 steps & forward with 1 step. Open/ Close Use this button to Open/Close the TFT LCD Panel.
INTRODUCTION Track / CH Up/ Down - Use this button to tune to a station to be stored in the radio / TV mode . 1) Track up key with pressing over 2 seconds should be Radio Frequency or TV Channel memory. 2) Track down key with pressing over 2 seconds should delete Radio Frequency or TV Channel to be momorized. - Use this button to select a track in audio CD, MP3. - Use this button to select a chapter in the DVD video. Seek & Tuning Up/ Down -Radio Mode: The unit starts to seek next station.
INTRODUCTION 4. BATTERY Preparing & Using The Remote Control BATTERY INSTALLATION NOTICE (BATTERY) PLEASE FOLLOW THE INSTRUCTIONS BELOW. INCORRECT BATTERY USEAGE MIGHT CAUSE EARLY DISCHARGE, LEAKAGE OR CORROSION DAMAGE. * Do not insert battery in the wrong direction. Be sure to observe the correct polarity (+/-) as indicated in the battery compartment. * It is dangerous to charge/heat/open or short circuitry the battery.
INTRODUCTION 5. Remote Control Key Power/Mode Mute Open /Close Volume Up/Down AF / TA (RDS Function) PTY/ REG (RDS Function) Track (P.Seek/CH) Up / Down Band (OSD ON / OFF) Menu Enter Set Up DVD Menu Slow Disc (Seek/Manual) Up / Down Tilt / Navi (Navigation Function) Rear Monitor NTSC/PAL(DVD ONLY) P.
Connecting to Power & Multi Channel AV Control Unit System 1. Connecting to Power System The illustration below is showing power system connection. Please also refer to the owner s and installation manuals supplied with the associated equipment. If it doesn t have corrected connection, it may cause unexpected damage. 1-1. HEAD UNIT Notice Make sure the connection of Parking Brake wire. If it has no connection, the unit will not show any picture.
Connecting to Power & Multi Channel AV Control Unit System 2.
Connecting to Power & Multi Channel AV Control Unit System 3. Connecting to Multi Channel AV Control Unit System The Illustration below is just possible examples with our Multi Channel AV Control Unit System only. The exact connection method will vary depending on the specific components selected for a particular installation. Please also refer to the owner s and installation manuals supplied with the associated equipment.
Connecting to Power & Multi Channel AV Control Unit System 4. Connecting to DVD Changer Control System Don’t use AV2 Audio L / R input of RT Box when DVD Changer is Connected. You can just use only AV2 Video input of RT Box from DVD Changer Video output. In case of using CD Changer instead of DVD Changer, the AV2 of RT Box can not be availed.
Connecting to Power & Multi Channel AV Control Unit System 5. Connecting to Multi Channel AV Control Unit System with Additional 6CH Amplifier The Illustration below is just possible examples for our Multi Channel AV Control Unit System with Additional 6CH Amplifier. The exact connection method will vary depending on the specific components selected for a particular installation. Please also refer to the owner s and installation manuals supplied with the associated equipment.
BASIC OPERATION POWER ON/OFF CLOSING THE MONITOR 1. POWER ON 1) Press POWER button to turn the power on and the monitor will be automatically positioned vertically when the monitor is opened. 1. Hold the left and right upper side of the monitor parallel with the front of the unit as the picture below. 2. You can also turn the power on by pressing the OPEN button. The power will be turned on and the monitor will be opened. 2. POWER OFF 2.
BASIC OPERATION 3. Use key and place cursor (Yellow bar) on the item you want to adjust (Ex. Contrast) and press ENTER key as picture above. 4. Press key to adjust the level of the selected item as picture below. 5. Press ENTER key at least for 2 seconds to return to the previous menu. 3. Use key and place cursor (Yellow bar) on the item you want to adjust (Ex. Tone/ Volume) and press ENTER key as picture below. 4. Use key and place cursor (Yellow bar) on the sub-item you want to adjust (Ex.
BASIC OPERATION 8. Do the same process as above to adjust Volume. 9. Press ENTER key at least for 2 seconds on current screen to return to the previous screen. Press Menu key about 1 second to turn MENU off directly. PRE ADJUST - (COLOR SYSTEM) 1. Press MENU key until the monitor displays following picture. 5. Press ENTER key at least for 2 seconds on current screen to return to the previous screen. Press Menu key about 1second t o t u r n MENU off directly. 6.
BASIC OPERATION 5. E a c h t i m e y o u p r e s s E N T E R k e y , Field/Standard should be changed at the same time as below. U.S.A / M-->CCIR1/ BG-->CCIR2 / BG --> Ireland/II’-->Australia/BG-->China/BG -->O.I.R.T/DK-->France/BG * When no key is pressed for 5 seconds, the menu will disappear. 4. Use key and place cursor (Yellow bar) on Band and press ENTER key as picture below. 5. Each time you press ENTER key, Band changes as below. U.S.A / 100KHz--> Europe / 50KHz--> O.I.R.
BASIC OPERATION 7. Each time you press ENTER key, Center changes as below FRONT --> REAR --> ALL --> OFF 8. Press ENTER key at least for 2 seconds to return to the previous screen. 9. Use key and place cursor (Yellow bar) on Navigation and press ENTER key as picture below. 2. Use Key and place cursor (Yellow Bar) on Sound Mix and press ENTER key. 3. Use key and place cursor (Yellow bar) on Sub woofer and press ENTER key as picture below. 10. Each time you press ENTER key, Navigation changes as below.
BASIC OPERATION 14. Press ENTER key at least 2 seconds on current screen to return to the previous screen. Press Menu key about 1 second to turn MENU off directly. * 5. Press ENTER key at least for 2 seconds to return to the previous screen. 6. Use key and place cursor (Yellow bar) on Angle and press ENTER key as picture below. When no key is pressed for 5 seconds, the menu will disappear. PRE ADJUST - (ADJUST REAR CCDFOR REAR VIEW CAMERA) 1 .
BASIC OPERATION * When no key is pressed for 5 seconds, the menu will disappear. RDS (Radio Data System) AUTO TILT SYSTEM 1. Press MENU key until the monitor displays following picture. 1. Press MENU key until the monitor displays following picture. 2. Use Key and place cursor (Yellow Bar) on RDS and press ENTER key. 3. Use Key and place cursor (Yellow) on On and press ENTER key as picture below. * When no key is pressed for 5 seconds, the menu will disappear.
BASIC OPERATION TUNING (TV-AUTO SEARCH) OVERVIEW OF THE RDS FUNCTION 1. After adjust TV system(Field/Standard) on Pre-Adjust, Press P.S/BSM to search TV channels. AF (Alternative Frequencies) / REG (Regional) * ‘Searching’ will be blinking as it searches TV channels and channel number is changing as it searches TV channels. 2. W h e n A u t o - S e a r c h i s c o m p l e t e d , memorized channels will be shown on the screen and cursor will be placed on the first channel as below.
BASIC OPERATION Regional mode off : The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented. PTY (Program Type) REG of individual segment is turned off together with displaying "REG OFF" on numeric display for a few seconds. - PTY MUSIC group ---> PTY SPEECH group ---> PTY off. When regional mode is off, the radio may switch from a national program station to a local variant of that program, or from a local station in an area to a local station in another area.
DVD VIDEO PLAYER OPERATION DVD VIDEO PLAYER OPERATION 1. CHANGING DVD SYSTEM SETTING Press SET UP button and then, there should be shown 5 categories as Language, Video, Audio, More Audio and Parental. 1) Language About 2CH or 6CH Setup: If 2CH is set into this menu with Analog out, it’s sound will come out by 2CH even though DVD title was set by 5.1CH Sound.
DVD VIDEO PLAYER OPERATION 2. BASIC PLAYBACK Preparation Insert a disc into the center of the insertion slot with the label side faced up. The disc plays automatically after loading. Note: Never insert foreign objects into the disc insertion slot. If the disc is not inserted easily, there may be an other disc in the mechanism or the unit may require service. Loading 8cm discs No adapter is required to play an 8cm disc. Insert the 8cm disc into the center of the insertion slot.
DVD VIDEO PLAYER OPERATION 1) POWER /MODE Use this button to turn on/off. For Turn off, hold this button about 2 seconds or longer. Each time This button is pressed, its source should be changed to AV1 AV2 DVD RADIO TV. 2) OPEN /CLOSE Use this button to open/close the TFT LCD Panel. 3) EJECT Use this button to eject a disc in slot for 2 seconds or longer. 4) PLAY/ PAUSE The disc will be loaded and playback will automatically and if it is pressed once more during playback, it will be worked by pause.
DVD VIDEO PLAYER OPERATION 5) CHANGING SUBTITLE LANGUAGE (S -TITLE) It is possible to change the subtitle language to a different language from the selected one. This operation works only with discs on which multiple subtitle languages are recorded. Press S-TITLE button for 3 seconds or longer during playback. Press repeatedly S-TITLE until the desired language is selected. To eliminate the On Screen Subtitle, please press S-TITLE repeatedly to select OFF.
DVD VIDEO PLAYER OPERATION Playback of the selected item will begin. 8) REPEAT (SET UP) To repeat viewing or listening, press REPEAT during playback. Each time this button is pressed, the TV Screen changes as below. Repeat Chapter Repeat Title Shuffle Off.(DVD Title) / Repeat One Shuffle Off.(Audio CD Title) 9) A-B REPEAT Repeating sections between two specific points (A-B repeat). Press A-B during playback at the point where repeat play is to start(A).
DVD VIDEO PLAYER OPERATION For further information, also refer to any instructions that may have been packaged with the disc you are playing. After playback When the unit is not in use, remove the disc and turn off the power by pressing the POWER button. (Do not remove the disc if you plan to use the LAST MEMORY function explained on the next page). NOTES - If appears on the screen when a button is pressed, it means that the selected function is not available on the disc you are playing at that time.
DVD VIDEO PLAYER OPERATION 3. LAST MEMORY - PICKING UP WHERE YOU LEFT OFF & OTHERS This unit is equipped with a LAST MEMORY function which lets you resume viewing of a movie from the point where you left off. You must press only PLAY button, not Power button in case the power has been turned off (and stand by power) NOTE The Last Memory function is not supported once the disc is removed from the slot. 1) VOLUME UP / DOWN Adjust the Volume by pressing the VOLUME buttons.
DVD VIDEO PLAYER OPERATION 4) ANGLE Some DVDs may contain scenes which have been shot simultaneously from number of different angles. For these discs, the same scene can be viewed from each of these different angles using the ANGLE button. (The recorded angles differ depending on the disc used.) 5) SLOW DISC Press and hold this button during playback. Every time this button is pressed shortly, its speed should be changed by x2, x4, x8, x20 with fast forward and fast backward.
AM/FM RADIO OPERATION 1. BAND (AM / FM) Each time this button is pressed, the band will be changed to FM1 FM2 FM3 AM1 AM2 2. PRESET SCAN / BSM Following your desired band selection, press P.S/BSM button about 2 seconds or longer, and then tuner will search until stations of sufficient strength have been found and will store them in sequence. The stored each station will playback for 5 seconds in sequence until you select one stored channel by pressing P.S/BSM one more. 3.
TV OPERATION 1. PRESET SCAN / BSM Firstly, select the desired station and press the PS/BSM button shortly. And then, Tuner will now search until stations of sufficient strength have been found and will store them into TFT LCD automatically in sequence. 2. MANUAL UP/ DOWN To find out a desired TV channel, press this button shortly. 3. TRACK (P.SEEK/ CH) UP/ DOWN Press this button to move to the stored TV channel you want. 4.
INSTALLATION PRECAUTIONS Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater or where it would be subject to dust, dirt or excessive vibration. Use only the supplied mounting hardware for a safe and secure installation.
INSTALLATION Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction. For example, the source may skip. 1. Align the holes in the unit with the vehicle mounting bracket and secure the unit with the accessory screws. 2. During installation, do not use any screw except for these provided. The use of different screws might result in damage to the main unit. Damage may occur if a screwdriver or similar tool is used with excessive force during the installations.
SPECIFICATIONS FM TUNER Frequency Range: 87.50 MHz to 108.
WARNING DO NOT HOLD THE LCD SCREEN PANEL WHILE IT IS OPENING OR CLOSING UNTIL IT IS COMPLETELY OPENED OR CLOSED. OTHERWISE, THE MOTORIZED MECHANISM WILL BE DAMAGED. BEFORE WORKING THE UNIT, READ THE OWNER S MANUAL CAREFULLY AND FOLLOW UP THE INSTRUCTIONS IN IT. ALWAYS WORK THE UNIT WITH THE REMOTE CONTROLLER OR THE FUNCTION BUTTONS ON THE UNIT. OTHERWISE, THE UNIT CAN BE DAMAGED.