7 " W i d e LCD M o n i t o r W i t h 4 M o u n t in g O p t i o n s PLVH7IP INSTRUCTION MANUAL www.pyleaduio.
Table of Contents About the liquid crystal display (LCD) panel 2 Precautions 3 Control & Layout for monitor / wireless remote 4 Accessories 5 Connection diagram 6 Replacing the remote control battery 6 Installing headrest with shroud 7-8 Installing sun-visor with shroud 9-10 Installing of headrest case 11 Function Setting 12-18 Troubleshooting guide 18 Specifications 19 1
About the liquid crystal display (LCD) panel 1. Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a malfunction, the picture may become unclear, or the LCD panel may be damaged. 2. Notes on cleaning -clean the LCD panel with a slightly damp soft cloth. - do not use solvents such benzine, thinner, commercially available cleaners or antistatic spray. 3. Do not use this unit temperatures under 5 o C (41 o F) or over 45 oC (113 oF). 4.
Precautions Please read this manual completely and carefully prior to attempt to install your new car video equipment. Install correctly, your new equipment will provide you with years of enjoyable and safe usage. Installing this unit requires technical expertise. This unit should be installed by a qualified technician or service personnel. If you try to install this unit by yourself, do it properly, referring to the installation and wiring diagrams in this operating manual.
Control and layout for the monitor Front Audio Output Front audio output (headphones) Blue screen when no video signal MMI Input Front audio video input (Plug & Play for Ps2 or games) Remote Sensor Remote control IR sensor Power On / Off Turn on/off the monitor Front A/V Input Front audio video input Menu Press to display MENU with functions and setting Power Cord (Male) Adjust Increase This multipurpose button serves to increase the selected parameters, such as volume, contrast etc.
Accessories Universal Stand Headrest & Sun Visor Shroud Headrest Bag Remote Control Extension Min Din Cable Key-for removing the monitor from headrest or visor shroud AV Cable INSTRUCTION MANUAL Earphone Instruction Manual 5
Fuse replacement Never use fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. Connection Diagram E a rp When replacing the fuse, be sure to use one that matches the amperage described on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest your’s dealer.
Steps For Installing Headrest with Shroud Setup work Remove the headrest and set it in an uncluttered work area. Pay the appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the headrest! If you have any doubtsabout this typeof installation, please consult your local mobile electronics retailer. Cutting and making holes in the headrest will causeelectronic damage which is expensive to repair.
Route the cable through the headre st Run the su pplied cable through the opening a nd ou t to the bottom of the headre st. If possib le , conceal the wires with a sh aft covering. Con nect the power, g round a nd video lea ds to test the MO NITOR. B efore co nnecting the mon itor, pull the conn ectin g cable th ro ugh the h eadrest shroud as shown in diagram. Place th e hea drest hou sing into the o pening a nd secure with correct fa steners.
Steps For Installing Sun-visor with Shroud Setup work Remove the visor and set it in an uncluttered work area. Pay appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make surethe screws are not long enoughto go through the visor! If youhave any doubts about this type of installation, please consult yourlocal mobile electronics retailer. Cutting and making holes in the visor will cause electronic damage which is expensive to repair.
Route the cable through the visor Run the sup plie d cable th rough the o pening an d out to the bottom of the visor. If possible, conceal the wires using a shaft coverin g. Conn ect th e power, gro und an d vid eo lead s to test th e MONITOR. Befo re co nnecting the monitor, pull th e co nnecting cable assembly through the visor housing a s shown in diagram. Place sun-visor shrou d into the opening and secure it with co rre ct faste ners.
Steps For Installing Headrest Bag Insert the monitor to the headrest bag Put the monitor with headrest bag at the rear side center of pillow. Rear side of headrest Cut the magic tape to the fit your pillow size, then fasten it as X as diagram show.
Function setting SOURCE Press MENU button (1)from the remote or press manu button (1) from the monitor to call out the function menu, press button (2 or 3) to the desired setting. AV1 AV2 AV3 RETURN 2 1 3 Monitor Remote SOURCE When screen appears “SOURCE” Press Menu button (1) to enter video signal input selection. [ The symbol show current video input. ] AV1 AV2 AV3 RETURN 2 1 3 Monitor Remote SOURCE Press the button( 2or3) to move the symbol and choose video signal input.
PICTURE When screen appears “PICTURE” press the menu button (1)to enter picture parameters setting. BRIGHT CONTRAST COLOR RETURN 2 1 3 Monitor Remote PICTURE Press the button( 2or3) to adjust the symbol to choose “BRIGHT”. Press menu button (1) to enter BRIGHT setting. [ Brightness: Makes black appear darker or lighter ] BRIGHT CONTRAST COLOR RETURN 2 1 3 Monitor Remote PICTURE Press button 2: adjust brightness to lighter level. Press button 3: adjust brightness to darker level.
PICTURE Press the button( 2or3) to adjust the symbol to choose “CONTRAST”. Press menu button (1) to enter CONTRAST setting. [ Contrast: Narrows or widens the gap between black & white (darken & brighten)] BRIGHT CONTRAST COLOR RETURN 2 1 3 Monitor Remote PICTURE Press button 2: adjust contrast to brighter level. Press button 3: adjust contrast to darker level. Press button 1 to confirm setting. [Contrast adjustable level: 0~100 .
PICTURE Press button 2: adjust more color intensity level. Press button 3: adjust less color intensity level. Press button 1 to confirm setting and exit. [Color adjustable level: 0~100 . Preset: 50] 2 1 COLOR 50 3 Monitor Remote PICTURE Exit Picture setting, Press the button( 2or3) to adjust the symbol to “RETURN”. Press menu button (1) to exit. BRIGHT CONTRAST COLOR RETURN 2 1 3 Monitor Remote AUDIO When screen appears “PICTURE” press the menu button (1)to enter picture parameters setting.
AUDIO Press button 2: adjust sound to more loud level. Press button 3: adjust sound to more soft level. Press button 1 to confirm setting and exit. [Volume adjustable level: 0~100 . Preset: 50] 2 1 VOLUME 50 3 Monitor Remote FUNCTION When screen appears “FUNCTION” press the menu button (1)to enter function parameters setting.
FUNCTION Normal 4:3 Full 16:9 Diagram Diagram When the symbol at “SIZE” Press the MENU (1) button repeatedly to change the picture display size to Full 16:9 or Normal 4:3 as the diagram show. INVERT 1 SIZE: Full 16:9 Language Select: RETURN 2 1 3 Monitor Remote FUNCTION When the symbol at “Language Select:” Press the MENU (1) button to enter the OSD languages display.
FUNCTION When the symbol at “Exit” Press the MENU (1) button to exit the setup. Exit 2 1 3 Monitor Remote Troubleshooting guide The following checklist will help you solve problems you may encounter with your unit. Before going through the checklist below, check the connection and operating. if you can not solve the problem with follows guide, please contact your nearest dealer. Problem Cause/solution The power cord or battery has been disconnected. The fuse has blown. Press power on.
Specifications: LCD Drive Method: a-SI TFT Active Matrix Visible Screen Size: 7 Inch Wide Screen (Diagonal) Aspect Ratio: 16:9 Display Format: 480 x RGB x 234 Number of Pixels: 336,960 Response Time: 15ms Backlight : High Brightness CCFT Luminance: 380 cd/m 2 #3 Backlight Life: 15,000 Hrs #1 Contrast Ratio: 300:1 Viewing Angle: (H/V): 120 o / 100 o o o o o Operation Temperature: -20 C ~ 70 C / -2 F ~ 158 F Video Color System Input: NTSC & PAL Compatible On Screen Display: Multi Languages (English, German, F