0.
1. Table of Contents------------------------------------------------------ 1 2. Warning --------------------------------------------------------- ------- 1 3. Usage Notice ---------------------------------------------------------- 2 4. Package ---------------------------------------------------------------- 3 5. Remote Control --------------------------------------------------------3 6. User Controls ----------------------------------------- ---------------- 4 7.
Usage Notice Follow all warnings, precautions and maintenance as recommended in this user's manual to maximize the life of your LCD monitor To avoid the damage of the LCD monitor and risk of electronic shock, do not permeate the LCD monitor with water or any drink. When this happens, turn off the power, unplug the power cord and send the LCD monitor to your local dealer or our service cen-ter as soon as possible. Use a regular power specification of DC 12V .
Package This LCD monitor comes with all the items below. Check to make sure your unit complete. Contact your dealer immediately if anything is missing. PLVW1040R * 10.
User Controls User Control Overview * Panel Control Start Your Installation Wiring * Monitor connection 4
Setting Up The Dome Lamps *Operating the dome Lamps 1. There are three function buttons for the Dome lamps operation: OFF, DOOR, and ON. (Refer to the following figure) A. OFF: To turn off the lamps. B. DOOR: To make the lamps turned on only when car doors are opened. C. ON: To turn on the lamps.
Installation your Monitor Take care to select a suitable fitting location and securing method for the monitor: *The unit should not distract or obstruct the driver. *The installation should not inhibit the entry to, or the exit from the vehicle. *The unit should not interfere with other vehicle components e,g (sliding sunroof). *Make sure the unit is installed to a secure, robust mounting location and cannot become dislodged in the event of an emergency stop.
Closing Monitor 1. Return the monitor to the central viewing position. (Refer to the following figure) 2. Push the monitor/TV back into the monitor base unit until the screen engages with the release button. Operating the Monitor * Powering up the monitor The monitor will be automatically turned on when releasing the monitor from the base unit and "OFF" when it is closed. Operating Instructions Opening the Monitor 1. Press the monitor release button to lower the LCD screen. 2.
* OSD Menus in A/V Source Press the "+" key to enter the sub-menu. Press "MENU" button to go back to the main menu. MAIN MENU A. Source Selection Menu CUBS.1 = NTSC H. SYNC = +15.7K Hz V. SYNC = -60.0Hz SOURCE BRIGHTNESS CONTRAST COLOR HUE SOURCE AUDIO RECALL AUTO DETECT S-VIDEO 1 2 VIDEO 1 VIDEO 2 RETURN EXIT B. Audio Input Selection Menu AUDIO MUTE VOLUME RECALL RETURN * Quick Adjustment OSD Menus 1. By pressing the "SELECT" button, you may open the following OSD menus directly.
Function Descriptions Panel Control * Menu: Pop up the OSD menus. Press the "Menu" button again to exit the OSD menus. When in sub-menu, press "MENU" again to go back to the main menu. * Select: 1. Switch among each function items in OSD menus. 2. Make quick adjustment of "brightness" and "contrast". * +/- Keys: 1. Press the "+/-" key to increase or decrease volume. 2. Make item selection in OSD menus to increase or decrease parameters as well.
Specifications Screen Size Resolution Number of colors Pixel pitch & Format Brightness Maximum Contrast Ratio Operating Temperature Storage Temperature Back light View Angle L/R View Angle U/D 10.4" diagonal 800 (H) x 600 (V) pixels 262, 144 colors 0.264 (H) x 0.264 (V) mm Vertical Stripe Arrangement 150 cd/m2 200 0 C ~ 50 C -25 C ~ +60 C Cold cathode Filament Tube 45/45 Degrees 15/35 Degrees Monitor Dimension Monitor Weight 236(W) x 174.3(H) X 5.7(D) mm 1.
Appendix Changing the New Battery in Remote Control 1. Push the cassette button to wards the right. (As shown # 1 in below figure) 2. Pull the all battery cassette away from the remote control. As shown # 2 in below figure) Change a new battery.
