ALL-IN-ONE LCD PROJECTOR MODEL NO.
Accessory and purchasable parts In order to use the projector well ,when you open the carton of projector ,please check the full accessories Accessory list: Projector--------------------------1unit remote control--------------------1pcs power cable-----------------------1pcs AV signal cable-------------------1pcs HDMI signal cable---------------1pcs VGA signal cable-----------------1pcs warranty card---------------------1pcs manual----------------------------1pcs spare fuse-------------------------1pcs clea
Specification WARNING warning Please remember the model Number and series number if you need. And please check all accessories when you drop the carton package LCD MODEL NUMBER SERIES NUMBER Model video Input signal audio When you use this projector , please read this manual carefully Warning Output signal Do not see the light from the lens ,it is high bright lamp. It will damage your eye .
Trouble shooting problem Possible situation If choose the right signal mode No image If open the input signal devices If connect the signal cable If connect the signal cable well Under VGA mode ,setting the computer frequency must over 75KHz? Dust cover the filter Projector turns off automatically The filter long time no clean, please clean it by water The voltage is too low or big fluctuation Lamp doesn work t Safety precautions When you turn off the projector , the lamp too hot, please wait at le
Caution Trouble shooting About the installation In order to improve the projector service life, About Open and close the projector It shouldnot place in a wet and when open the projector ,connect ventilation condition the power cable and press the "power" Donot put the projector under the sunshine key on the panel .the projector will directly work ,but the lamp will be bright more and more .
Installation Maintenance Use Screwdriver to remove the four screws as picture PROJECTOR INSTALLATION Please use the setup instruction below: Speaker L Speaker R Screen Subwoofer Speaker C 4. Use a small screwdriver to insert the lamp terminal to get the lamp out Projector DVD Amplifier Appreciate seats Door Speaker Rs Speaker Ls Before replacing the lamp, make sure the lamp are cold.
Projector Installation Maintenance Standard setting (front projection ) Replace the projector lamp Please refer to the following instruction ,adjust your picture size and distance, the projector must be put on a strong flat desk or suspended on the ceiling by mounts Inc h 8 4n c h 4:3 Image ratio I Inc Inc h M M our projector lamp have 6months warranty ,But in different use environment after 6000hours ,the lamp brightness will reduce and the image will become dark.
Projector installation Maintenance When projector working ,the projector will be overheat Now many projectors use fans to cold it .But our projector use two filters to cold the projector .When use the projector,there will be some dirt to cover the filter . So please clean the filters per month.
HDMI and USB setting Projector installation Input port instuction If you want to paly the external HDMI signal or USB function, ,you must choose the DVD channel ! This projector can support HDMI signal ,component video signal,s-video VGA, and USB input ,TV signal ,the audio in and audio out function Play the external HDMI signal as following:: 1.firstly open the projector power,the indicator light is flash, Then press the power key on the panel or remote control , the projector begin to work 2.
Projector install DVD menu setting and reflected image play Digital setup When you choose the digital setup ,the screen will display as follow: Digital setup VGA Op mode dynamic range dual mono Connect Mp4 AVI and picturer of USB TV AUDIO VIDEO S-VIDEO Audio output Op mode can setup for line out or FR adjust Dynamic range can setup audio output range Note: If you adjust the DVD menu wrong and cause problem .the projector cannot play the DVD disc. Please reset the menu .
Remote control instruction DVD menu operation setting Speaker setup DVD Mode or PROJECTOR MODE DVD open/close When you choose the speaker setup ,it will display as following: Power HDMI input choise you can choose the HDMI input from other devices.
DVD menu operation setting Panel keystoke instruction Panel keystoke sketch map Audio setup: When you press the audio setup key ,it will display as following : AUDIO SETUP AUDIO OUT MIC SETUP KEY ECHO MIC VOL Video setup: When you press the video setup key ,it will display as following : Adjust the image trapeziod On DVD mode,press this key, stop or begin the disc Remote control reciver On DVD mode ,press this key to stop to play. press it again to play again ,if press it twice , it keep stopping.
DVD menu operation setting If the projector is the new one please read projector install chapter placed the projector connect the powerwire and the signelwire the operation as follow: Language setup: When you choose the language setup ,the screen will display as following Open operation 1.Before use the remoter . Put in two 7 size battery in it LANGUAGE SETUP 2.
Image adjustment DVD menu operation setting When you choose the DVD channel ,the DVD begin to work when the DVD interface appear in the screen, put the disc inside the projector , then you can enjoy your program.
Menu setting Menu setting Menu setting method 1. Using the projector press menu key, the picture disply on screen to adjust the menu(picture one) 2. press key the menu entre into image > volume > function > system > setting > image adjust interface 3. Elect the adjust interface use key elect the item that need to adjust(picture two 4. use key to adjust the elect item paremeter 5. Finished the elect item parameter press the menu key again exit the page 6.
