PT-600A POWER INTEGRATED STEREO AMPLIFIER REMOTE SENSOR BASS 2 0 TREBLE 2 4 2 4 6 6 8 8 10 PHONES 10 0 2 4 4 6 6 8 8 10 10
PRECAUTIONS Thank you for purchasing this HI-FI product. Taking time to read these operating instructions carefully before use Do not remove the case and bottom panel will acquaint you fully with all its features and help ensure Any inspections or adjustments inside the unit optimum performance. may lead to malfunctions and electric shocks. Do not touch any of the inside parts. In order to simplify the explanation illustrations may sometimes differ from the originals.
CONNECTIONS Connection precautions Playback Connect connections: the TAPE PLAY When connecting, either disconnect the power plug terminals to the output (LINE OUT) terminals on the from the power outlet or turn off the unit’s power cassette deck using the pin-plug cord. using the POWER switch. Check the left and right channels and connect properly TA P E P HO N O CD AV 1 AV 2 TUNER P L AY EQ R EC P L AY R EC L (Left to L and Right to R).
CONNECTIONS Speaker systems PHONO Connect the speaker systems to the SPEAKERS terminals Connect the turntable’s output cord L (white) plug to the L on the rear panel of the unit with the speaker cords. PHONO terminal and the R (red) plug to the R terminal. When viewed from the front (the listening position), the If your turntable is equipped with a grounding cable, speaker mounted on the left should be connected to the L connect it to the unit’s GND terminal.
PANEL INFORMATION 1 2 3 4 5 6 POW ER REMOTE SENSOR BA SS 2 TRE BLE 0 2 4 2 4 6 6 8 8 10 10 0 2 4 4 8 8 6 6 10 10 PH O NE S 18 17 16 15 14 13 12 11 10 9 8 7 1. POWER SWITCH Power is supplied to the amplifier when this switch is depressed and the power is switched off when the switch is released. 11. AV1/AV2 This switch is pressed when this unit is connected to the external amplifier. 2.
OPERATING PROCEDURES REMOTE SYSTEM EQ TAPE TUNER CD RIGH T TAPE PHONO CD AV1 AV2 TUNER PLAY REC PLAY LE FT INTEGRATED CIRCUIT AC 220V - 230V ~50Hz L EQ REC L L R R _ _ SP E A K E R S6 ~ 8 Ω A U D IO Before starting operation Check that the controls have been set to the following positions before commencing operation 2.Operate the program source unit. Rotate the VOLUME control counterclockwise as far 3.
OPERATION REMOTE CONTROL 2 PHONO TUNER 7 TAPE BAND MEMO SCAN MEMO HOLD VOLUME 3 PRESET EQ EXTERNAL PROCESSOR 4 5 AV1/AV2 CD 6 1 Remote Controlling Instructions The remote control box can directly control majority of system functions of HI-FI SYSTEM. The functions include power control of the whole system, Volume control, sound field control, CD operation control, Tuner operation control and also source control function.
SPECIFICATIONS Signal to noise ratio (short-circuit, A-network) Power output Min. RMS, both channels driven, from 40-20 kHz, with no more PHONO……………….60dB than 0.1% total harmonic distortion. TUNER, TAPE PLAY….70 dB 50 watts per channel into 6 ohms. Power requirements Load Impedance…………………..6 ohms Power voltage…….220V ~ 50Hz Total Harmonic Distortion………less than 0.05% at 1/2 rated For U.K………240V ~ 50Hz RMS power output. Frequency response (at 1 watt)…..20 to 20 kHz, + 1 dB, -2dB For U.S.
