ple420p 15KH m a n u a l www.pyleaudio.
congratulations . . . for choosing Pyle Audio, and congratulations on joining a select group of dedicated enthusiasts committed to the very best in mobile sound performance and dependability. You are now the proud owner of one of the world’s most sophisticated electronics components. This Pyle product is the result of an extensive engineering program with the sole purpose of creating the finest mobile audio experience imaginable.
owner’s manual table of contents Ple420p i congratulations 1 table of contents 2 general features 3 specifications 4-5 features and controls 6 mounting and installation 7 electrical connections 8-9 system wiring 10 precautions and troubleshooting 1
general features ple420p 4 band parametric controls ple420p pre-amp DVD & AUX input via RCA jacks subwoofer output output volume control 3.
p owner’s manual specifications ple420p ple420p 4 band parametric boost/cut frequency response input level SUB 150Hz, LOW 400Hz, MID 2.5KHz, HI 15KHz 18dB 15 Hz - 30 KHz (+/– 1 dB) 200 mV (for 400mV output) total harmonic distortion (THD) < 0.03% (at 400mV output) output impedance 10K Ohms signal-to-noise ratio (S/N) 90 dB separation 50 dB current drain power supply voltage dimensions (W x H x L) mm inches 200 mA 12V DC Neg. Ground 178 x 28 x 105 7 x 1.1 x 4.
features and controls ple420p 7-1 front 16 rear 4
owner’s manual features 1. 3.5mm DVD input jack 2. DVD & AUX input switch 3. fader control Connects to the DVD source with 3.5mm plug cable. to select the AUX or DVD inputs. • in a 2 Amplifier, 4 Speaker system, rotating the knob to the FRONT side increases the level of the front speakers; rotating to the REAR side increase level of the rear speakers. At mid position, both sets of speakers are at maximum level.
mounting and installation ple420p 4 x 6 mm machine screw (4) dashboard mounting Please take the time to install your new Pyle Signal Processor securely, according to this diagram, using the hardware provided. Signal Processor enclosure This Half-DIN size unit can also be installed in the dash adjacent to the head unit, provided that there is a slot available.
owner’s manual electrical connections ple420p rear RED WIRE ORANGE WIRE Fuse 1A Fuse 0.
system wiring basic system application using front, rear, and subwoofer amps ple420p left and right DVD outputs from head unit left and right DVD inputs + – + REAR CHANNEL power amplifier – L REAR CHANNEL speakers R + – + FRONT CHANNEL power amplifier – L FRONT CHANNEL speakers R + L – + 8 SUB CHANNEL power amplifier SUB CHANNEL speakers R –
owner’s manual system wiring basic system application using a 4 channel amp and subwoofer amp ple420p left and right DVD outputs from head unit left and right DVD inputs + + – + 4 CHANNEL power amplifier – – L/R REAR speakers L/R FRONT speakers + – + L – + SUB CHANNEL power amplifier SUB CHANNEL speakers R – 9
precautions ple420p • Never drive with the volume raised so high you cannot hear what is occuring in traffic around you. • Be aware that repeated exposure to excessive volume levels can permanently damage your hearing! • Keep all electronics away from moisture, dust, extreme heat or extreme vibrations. • Pyle Audio products are capable of sound pressure levels in excess of 150 dB. Continuous exposure to sound pressure levels over 100 dB may cause permanent loss of hearing.
owner’s manual notes 11
limited warranty policy All Pyle products are carefully constructed and thoroughly tested before shipment. Products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchaser. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyle.
