PLTVR5 OWNER’S MANUAL COLOR LCD TV/RECEIVER WITH CD CHANGER CONTROL
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
MOUNTING THE TUNER UNIT 4 2 6 6 5 4 7 1 6 3 1 8 5 7 5 7 3 8 2 Step 1 1. 2. 3. 4. Step 2 Bracket (A) Mounting Bolt (M5 x 5) Bracket (B) Hexagonal Bolt with Washer (M6 x 12) 5. 6. 7. 8. Tapping Screw with Washer (M5 x 12) Spring Washer (M6) Spring Washer (M5) Double Sided Tape INSTALL THE DISPLAY UNIT Before install the display unit, please remove its tail screw and cable parts.
1. Dashboard 1 2. Nut (M5) 6 4 3. Spring Washer 4. Tapping Screw with Washer (M5 x 25) 2 7 5. Screw 5 3 6. Plain Washer 7. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. (Fig. 2) Removing the unit 1 1. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers upward and out to makes it possible to remove the unit.
HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. Press release button to draw out the screen display. Release Button 2. Turning the display upward. 3. Adjusting the viewing angle. Angle should be adjusted slowly without applying unreasonable force.
4. Turning the display downward. Make sure to return the display to centre position before drawing in. It cannot be draw in with its angles adjusted. 5. Push the panel, the display will be drawn in.
ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) RADIO/TV MAIN UNIT (VIEW FROM FRONT) TV DIVERSITY ANTENNA INPUT AV INPUT TV MONITOR AV1 CDC INPUT RADIO CONTROL AV2 Rch RED GREY PLUG BLACK PLUG BLACK/GREY CABLE BLACK CABLE FROM VIDEO/AUDIO SOURCE VIDEO OUTPUT Lch WHITE 75ohm RF WIRE (BLACK) REAR RCA CABLE (FOR RCA LINE VERSION ONLY) FRONT RCA CABLE Lch WHITE Rch RED (GREY) (BROWN) RADIO ANTENNA INPUT TV DIVERSITY ANTENNA INPUT TO CD CHANGER GREY/BLACK GREY BLACK GROUND Y
OPERATION 12 3 32 9 11 22 17 23 10 18 19 25 4 16 15 20 21 24 29 6 30 8 28 8 26 5 7 27 31 2 13 1 14 4
GENERAL OPERATION • ON/OFF Switch on the unit by pressing POWER button (1). When system is on, press it again to turn it off. • FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display. • SELECTING SOUND MODE Press SEL button (6) to move display through volume, bass, treble, balance and fader functions. Use VOLUME > (7) and VOLUME < (8) buttons to adjust the selected mode.
• MONO/STEREO Press MON button (10) to select mono or stereo mode. In radio operation, press the button to select mono or stereo reception for radio station. You can sometime improve reception of distant stations by select mono mode. • SETTING THE CLOCK Press DSP button (5) to change the display into clock display. While the current time is appeared on the display, press it again to return to frequency showing.
RADIO OPERATION • SELECTING BAND Press BAND button (11) to change between three FM bands and two AM bands. Each band stores up to six preset stations. FM1 FM2 FM3 AM1 AM2 • SELECTING STATION During radio mode, press button (13) to increase frequency or button (14) to decrease frequency by one step of channel spacing. Hold the button longer for fast tuning. The frequency is updated correspondingly on display.
CDC OPERATION • SELECTING TRACK During CDC mode, press button (14) or button (13) shortly to move to the previous track or the next track. The track number shows on the display. • SELECTING CD Press D.UP button (17) to select next disc and D.DN button (18) to select previous disc. • REPEAT THE SAME TRACK Press RPT button (19) to continuously repeat the same track on the current disc. Press it again to continuously repeat all tracks on the current disc. Press it the third time to stop repeating.
TV OPERATION • SELECTING RECEIVING MODE Press TV/AV button (31) to select among TVch/AV1/AV2. • PICTURE ADJUSTMENT/PROGRAM SETTING/SYSTEM CONTROL In TV mode, press MENU button (23) to enter the main menu. And the menu includes three sub-menus: PICTURE MENU, TUNER MENU and SYSTEM MENU. Press the button repeatedly or press CHANNEL SELECT + button (28) or CHANNEL SELECT – button (29) to select the desired item then press CONTROL + button (24) or CONTROL – button (25) to enter the corresponding sub-menu to set.
In the course of scanning, press SCAN button (26), “SCAN OFF” will also display on the screen and it stops on the TV channel just scanning. • SCREEN DISPLAY Press DISP button (27), the screen will display the current status such as TVch/AV1/AV2, the COLOR SYSTEM and the SOUND SYSTEM on the right-top corner. In AV mode, there is no SOUND SYSTEM display. • REMOTE SENSOR Point the remote control handset to the remote sensor (30). Press the function keys on the handset to control TV.
REMOTE CONTROL HANDSET 1 2 3 4 16 5 17 6 8 7 9 10 13 11 14 12 15 CONTROL & FUNCTION KEYS 1. 2. 3. 4. 5. POWER TV/AV 0-9 -/-MUTE = = = = = 6. 7. 8. 9. 10. 11. 12. SCAN MENU / / VOL + VOL – PICT = = = = = = = 13. 14. 15. 16. RETURN CH + CH – DSP = = = = 17. SORT = Press POWER to turn the unit ON or OFF Switch between TV/AV1/AV2 Numeric buttons, press to select the corresponding channel Digital selecting button, cooperatively used with numeric buttons Press to mute the sound.
SPECIFICATION GENERAL Power Supply Voltage Maximum Power Load Impedance Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) : DC 12 Volts, Negative Ground : 4 x 60 Watts : 10 Ampere (max.) : + / – 10 dB : + / – 10 dB TV Monitor Screen Size Resolution TV Sensitivity : 5.0” TFT : 960 x 234 dots : 45 dBµV/PD (max.) @CH25 in average RADIO FM 87.5 to 107.
