PDWM4520 PDWM4540 PDWM4560 PDWM4520 - PDWM4540 - PDWM4560 Wireless Microphone System
CATALOG 1. FOREWORD FOREWORD --------------------------------------------------------------------------------------------- 2. INTRODUCTION --------------------------------------------------------------------------------------- 3. SYSTEM FEATURES 4. SYSTEM TYPE 2 2 ----------------------------------------------------------------------------------- 2 ------------------------------------------------------------------------------------------- 2 5.
FOUR CHANNEL RECEIVER FEATURES MICROPHONE-TRANSMITTER FEATURES 1. Power Button: Power ON/OFF the receiver. 2. Power Indicator: Indicates the power ON/OFF. 3. "AF"Audio Level lndicator: Indicates the wireless system audio signal level. 4. Volume Knob: Adjust the volume output of receiver. 5. "RF" Signal Indicator: It glows when the Receiver receive RF signal from Transmitter. 1. Grille: Protects the cartridge and helps reducing the breath sounds and wind noise. 2.
BODY-PACK TRANSMITTER FEATURES TRANSMITTER BATTERY INSTALLATION 1. Battery Installation of Handheld Microphone: Open the battery cover. Insert the supplied batteries into battery jar in polarity and cover the battery cover. 2. Battery Installation of Bodypack Transmitter: Push open the battery cover. Insert the supplied batteries into battery jar in polarity and close the battery cover. 1. Power and Audio Mute Switch. 2. Antenna: Transmit the RF signal of transmitter. 3.
BODYPACK TRANSMITTER CONNECTION 1. Lavalier Microphone Connection: Connect the connector of supplied lavalier microphone to the connecting jack of transmitter (shown as below) Set the transmitter work state in wireless lavalier system (L). SYSTEM CONNECTION 1. Receiver Power Connection: Connect the DC connector of supplied AC/DC adapter Into the DC power input of receiver. Plug the AC Input connecter into an AC120/60Hz or AC220V/50Hz outlet. (Shown as below) 2.
The audio gain control on transmitter has been factory-at the mid-range position for best performance in most applications. This may be necessary for soft singers or talkers, or guitar or basses with low outputs. TROUBLESHOOTING PROBLEM No Sound • To Increase Gain: Rotate the transmitter gain control clockwise using a screwdriver to increase audio gain. • To Reduce Gain: Rotate the transmitter gain control counterclockwise with the screwdriver to reduce audio gain.
HAND-HELD TRANSMITTER SPECIFICATIONS SYSTEM SPECIFICATIONS • Wireless Operating Frequency Range: Approximately 573.0 - 597.8 MHz (Available frequencies depend on applicable regulations in country where system is used). • Operating Range: 50m (approximately 164ft) under typical conditions • Audio Frequency Response: 100 to 18,000Hz, ±3dB • THD: <1% • Mobile state Range: > 100dB Power Requirements 1.
Pyle PDWM4520 Wireless Microphone System, UHF Quad Channel Fixed Frequency, 4 Handheld Microphones, Rack Mountable UHF Band Receiver System • Quad Frequency Channel Design (Channel1, 2, 3, 4) • Broad Frequency Response Range & Low Distortion • High Signal/Noise Ratio Performance • RF Signal &AF Signal LED Indicators • Radio Frequency and Audio Frequency • Independent Channel Adjustable Volume Controls • Detachable Dual Antennas • Rack Mountable System • Includes (4) Handheld Microphones • 4 XLR Output Conne
• Battery Powered: 2 x 'AA' Batteries (Included) System Receiver: • Batteries Included • Image & Spurious Rejection: >70dB • Weight: 180g • Receiving Sensitivity: -105dBm • Signal/Noise Ratio: >105dB Transmitters: • Border Upon Channel Rejection: >70dB • RF Power Output: >10dBm • T.H.D.: <1% • Modulation Type: FM • Audio Output Level: 0-300mV • Max. Deviation:+/- 40kHz • Power Requirements: 12-15V DC nominal1000mA • Nominal Power Current: <40mA • Dimensions (L x W x H): 15.51" x 9.25" x 2.