Invincible Series Amplifier
INTRODUCTION PYLE amplifiers provides high-performance sound reinforcement for your mobile audio equipment. Its versatility enables compatibility with optional Equalizers, Frequency Dividing Crossover Networks, and other audio processors in customized system. The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations. To achieve optimum performance, it is highly recommended that you read this Owners Manual before beginning installation.
PLANNING YOUR SYSTEM Before beginning the installation, consider the following 1. Do you plan to add additional mobile electronics equipment in the future? If you plan to expand your system by adding other components sometime in the future, ensure adequate space is left, and cooling requirements are met. 2. Should you use high or low level inputs? Your Amplifier has been designed to accept Low-Level (Pre-Amp outputs from your radio) signal source.
1. Ground: To Vehicle Chassis To avoid unwanted ignition noise caused by ground loop, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicle's Chassis. NOTE: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT, (1 METER). 2. +12 Volt (Fused) Constant Power: To Battery (+) Due to the power requirements of the Amplifier, this connection should be made directly to the positive (+) terminal of battery.
PANEL LAYOUT INV500DBA/ INV1000DBA FRONT VIEW INV559BA/ INV669BA FRONT VIEW INV500DBA REAR VIEW www.PyleUSA.
INV1000DBA REAR VIEW INV559BA REAR VIEW INV669BA REAR VIEW 6 www.PyleUSA.
TOP VIEW INV500DBA TOP VIEW INV1000DBA TOP VIEW INV559BA/INV669BA TOP VIEW www.PyleUSA.
CONTROL FUNCTIONS 1. RCA Input jacks These RCA input jacks are for use with source units that have RCA or Line level outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high quality twisted pair cables is recommended to decrease the passivity of radiated noise entering the system. 2. GAIN Control The level control will match the amplifiers senstity to the source units signal voltage. The operating range is 200mW minimum to 6W maximum.
7. Auxiliary Outputs The Auxiliary outputs offer PYLE amplifiers easy, unlimited system expansion. Route RCA, from the line out of the first amplifier to the line input of a second amplifier when using a single source output. 8. PHASE: Allows you to invert the subwoofer phase from 0 to 180. 9. SUBSONIC: The frequency can be adjusted between 10Hz and 50Hz. 10. REMOTE Controls the subwoofer amplifier gain from a remote location for ease of adjustment during listening.
WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 15. FUSE These fuses protect the amplifier against internal electrical damage and are meant to protect the amplifier only. All other power connections should be fused at the source. 16. SPEAKERS: Connect subwoofers to these terminals. SPEAKER CONNECTION MONO Channel System Design #1 INV500DBA 10 www.PyleUSA.
MONO Channel System Design #2 INV1000DBA www.PyleUSA.
5 Channel System Design #1 INV559BA 12 www.PyleUSA.
5 Channel System Design #2 INV559BA www.PyleUSA.
6 Channel System Design #1 INV669BA 14 www.PyleUSA.
6 Channel System Design #2 INV669BA www.PyleUSA.
TROUBLESHOOTING GUIDE Issue NO SOUND UNIT WILL NOT TURN ON Possible Cause Solution Check all fuses, replace if necessary. Is the power LED Make sure the power is securely illuminated? fastened.
0.2-6V 10-50Hz 0, 6, 12dB 0.2-6V NONE 0.01 250Hz NONE 50-250Hz 10-50Hz 0, 6, 12dB 0.2-6V 0-180° BRDGED POWER MAX @40hm THD FREQUENCY RESPONSE -3.00B HPF LPF SUBSONIC BASS BOOST (50Hz) ADJUSTABLE SENSITIVITY RANGE PHASE PRODUCT DIMENSIONS (L x W x H) FUSE 18.5'' x 8.13'' x 2.28'' -in 25Ax2 20K 0, 6, 12dB 250Hz 1CHx500W POWER OUTPUT RMS @10 hm INPUT IMPEDANCE (LOW LEVEL) NONE 0.01 1CHx350W 18.5'' x 8.13'' x 2.28'' –in 30Ax3 20K 0-180° 50-250Hz NONE NONE 1CHx1000W 1CHx700W 9.
Questions? Comments? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.