User manual

17
12. Troubleshooting
By purchasing the “Pyle Pro PDCD204 dual CD player”, you have acquired a safe, state-of –the art product.
Problems and malfunctions can occur nevertheless. We would therefore like to show you how to eliminate
certain malfunctions yourself.
Observe the safety instructions by all means!
Problem Cause Solution
No display after
Switching on the on/off
switch.
The mains cable is not inserted
properly in the mains socket or
the socket of the appliance
Plug in the mains cable properly.
CD has not been inserted properly.
Insert the CD with the written side
facing upwards.
CD is dirty. Clean the CD with a soft cloth.
The CD is not played
back.
The inserted CD is not an audio CD. Insert an audio CD.
The CD is dirty.
The CD is scratched.
Clean the CD
The CD is badly pressed. Renew the CD.
There are drop outs
when playing the CD.
The appliance is subjected to vibrations.
Place the dual CD player on an
appropriate stable surface.
LC displays are
not working.
The system connection cable
has not been inserted or has
not been Inserted properly.
Establish a correct system
Connection.
The PITCH slide control
is not working.
The PITCH button has not been
pressed.
Switch on the PITCH function.
A playback appliance is not switched
on.
Switch on the appliance
The wrong input has been
selected on the amplifier/mixer.
Select the right input.
No sound can
be heard.
The volume controls of the amplifier/
mixer or the output stage are set to
the “MINIMUM” position.
Increase the volume.
A cinch cable has become
disconnected from the audio output
of the CD player or from the amplifier/
mixer input.
Connect the clinch cable properly.
The wrong balance has been
selected on the amplifier/mixer.
Set the balance properly.
A channel is not working
The cinch connection cables is
defective.
Renew the cinch cable.
Repairs other than those just described should only be performed by authorized electricians.
18
13. Useful notes on handing CDs
 Hold CDs only by the edges. In this way you can prevent
fingerprints and dirt on the surface.
 Only touch your CDs with clean hands.
 If a CDs is dirty nevertheless, wipe it clean from the centre to
the rim with a soft, lint – free cloth. Avoid circular motion when
cleaning CDs. Do not use any solvents.
 Please use a commercially available CD cleaning agent (do
not use a cleaning agent for vinyl records) to remove dirt
which is difficult to remove, while observing the instructions of
the manufacturer.
 Do not write on your CDs since this can result in reading
errors. Do not apply any stickers or similar.
Stickers can become stuck in the CD player, for example, and damage it.
 Store your CDs in the supplied CD cases after playing them.
 Avoid exposing CDs to direct sunlight, heat and moisture when storing them.
14. Disposal
Dispose of the product at the end of its service life in accordance with the current statutory regulations.
15. Technical specifications
Operating voltage: 115V~/60Hz to 230 V~/50Hz
Power consumption: 16.5W
Playback media: Standard audio CDs, 8 cm and 12 cm and CD-R
Output voltage: 2 V RMS +/- 0.5dB
Channel separation: 89dB
Pitch speed control: +/- 4%, +/- 8%, +/- 16%
Pitch bending speed control: +/- 16%
Frequency response: 20-20000 Hz, +/- 0.4dB
S/N ratio: 92dB
Distortion factor: 0.01%
Analogue audio output: Unsymmetrical stereo cinch sockets
Digital audio output: Unsymmetrical cinch sockets
Drive unit weight: Approx. 5.2kg
Weight of the control unit: Approx. 1.2kg
Drive unit dimensions (W × H × D): 482 × 88.8× 267mm
Control unit dimensions (W × H × D); 482 × 88.8 × 50mm
Ambient conditions:
Storage temperature range: -20 to 60
Operating temperature range: +5℃ to +35℃
Humidity range: 25% to 85% relative humidity (non-condensing)