PLCD3MR OWNER’S MANUAL Marine Audio System • MP3 Player • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Automatic Memory Storing • Undetachable Panel • Preset Equalization • Electronic Shockproof (ESP) Function • Auxiliary Input Function • Remote Control www.pyleaudio.
CONTENTS Installation..........................................3 Take out screw before installation .......3 DIN Front-Mount (Method A)...............3 Installing the unit ..............................3 Removing the unit ............................4 DIN Rear-Mount (Method B)................5 Wiring Connection.............................6 Operation............................................7 Location of keys ..................................7 Switching on/off the unit .....................
INSTALLATION Notes: TAKE OUT SCREWS BEFORE INSTALLATION • Choose the mounting location where the unit will not interfere with the normal function of the driver. Before installing the unit, please remove the two screws. Take out screws before installation • Before installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the system works properly. • Use only the parts included with the unit to ensure proper installation.
INSTALLATION Sleeve Note: to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard. L Key Outer Trim Ring Front Panel Spring Washer Hex Nut Metal Strap Mounting Bolt R Key Plain Washer Tapping Screw 5. Mount the sleeve by inserting it into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver.
INSTALLATION DIN REAR-MOUNT (Method B) If your vehicle is a Nissan or Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Side view showing Screw Holes marked T, N Factory Radio Mounting Bracket Screw Screw Dashboard or Console To fasten the unit to the factory radio mounting brackets.
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE RED IGNITION SWITCH (ACC+) MEMORY BACK-UP (B+) YELLOW SUBWOOFER CABLE (GREEN) FUSE BLACK (GREY) GROUND (B–) POWER ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER RCA CABLE Rch RED Lch WHITE BLUE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION LOCATION OF KEYS 1 25 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2 3 24 23 22 21 20 4 5 6 19 18 17 16 15 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26.
OPERATION EQUALIZATION Press EQ button (5) to turn on equalization function and to select desired audio mode. There are five kinds of modes as shown below: GENERAL OPERATION • SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except EJECT button (7)). When system is on, press POWER button (1) to turn off the unit. FLAT • SOUND ADJUSTMENT Press SEL button (2) shortly to select the desired adjustment mode.
OPERATION • LOCAL/DISTANT Press LOC button (22) to select between local and distant stations. Local setting for reception of strong stations, and a distant setting for reception of weaker stations. This function is in effect during AUTO SEEK operation. MONO/STEREO Press MON button (21) to select mono or stereo mode. You can sometimes improve reception of distant stations by selection mono operation.
OPERATION CD OPERATION MP3 OPERATION • SWITCHING TO CD MODE If there is no CD inserted in the driver: Gently insert the CD with the printed side up into the CD compartment until you feel some resistance. The CD is drawn into the driver automatically. CD playback begins. If a CD is already inserted in the driver: Keep pressing MOD button (12) momentarily until the CD mode display appears.
OPERATION - Use the TUNE/SEEK/TRACK UP/DOWN buttons to list all songs under this directory and select the title. - Press BND/LOU (ENT) button to confirm and start the play. - Repeat the above steps if the newly selected title is again a directory. • SELECTING TRACKS BY AS/PS/DAUD BUTTON AS/PS (D-AUD) button is assigned as Digital Audio Mode selection button in MP3 operation. When pressed, it selects each mode of Digital Audio.
OPERATION • DISPLAY INFORMATION Press DSP button (20) to show following information, such as the clock, ID3 TAG (if available: song title, directory name, artist name and other contents…) and other information.
OPERATION SUPPORTED MP3/WMA DECODING MODES The main unit supports MP3/WMA (Windows Media Audio) decoding modes as below. Standard Bit Rate (kbps) MPEG1 Audio Layer 3 (44.1kHz) Windows Media Audio (44.1kHz) 32, 48, 64, 96, 128, 192, 256, 320 64, 96, 128, 192 DISC NOTE A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, star, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape etc.
REMOTE CONTROL HANDSET 1 7 4 3 8 9 6 5 13 2 12 14 11 10 16 15 FUNCTION KEYS & CONTROL 1. 2. PWR DSP Power ON/OFF Button Display Button 3. SEL Sound Mode Select Button 4. VOL Volume Up Button 5. VOL Volume Down Button 6. BND (LOU) Band Select Button (When pressed momentarily) 7. MODE Mode Button 8. TUNE/SKIP/CH Tune/SKIP Down Button 9. TUNE/SKIP/CH Tune/SKIP Up Button Loudness Button (When held down) 10.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 160 (D) x 50 (H) : 10 dB : 10 dB : 4 x 40 Watts : 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 45 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. No sound. Sound skips. Cause Solution The car ignition switch is not on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse.
8800-0C3021-