PLCD54MP MP3 DSP Stereo Receiver Power Amplifier AM/FM/MP3/USB/AUX Stereo Receiver, Single DIN, 30 Preset Memory Stations, LCD Display with Remote Control (Black)
INSTALLATION Preparation The preparation kit is necessary to mount the radio on the dashboard, this kit is available at electronics stores and car audio specialists, check the installation kit before using it to make sure it is the right one for your vehicle. INSTALL THE DEVICE 1. Lift the left or right top corner of the plastic outer trim ring then pull it out to remove it. 2. Insert the two bracket keys into the left and right side of the chassis to separate the chassis from the housing. 3.
WIRING CONNECTIONS PRECAUTION +12V DC NEGATIVE EARTH SWC 15A EXternal MIC Antenna Jack FUSE 15A Power/speaker Connector Rear RCA Output(Left) SUBWOOFER ANT:RADIO ANTENNA JACK F-L:Front RCA Output(Left) F-R:Front RCA Output(Right) R-L:Rear RCA Output(Left) R-R:Rear RCA Output(Right) Rear RCA Output(Right) Front RCA Output(Right) SUBWOOFER Front RCA Output(Left) HARDS FREE PUSH-TO-TALK PUSH-TO-TALK • Allows you to access SIRI or GOOGLE voice via Wireless BT.
CONTROL PANEL BUTTONS 1. (Power)/Mode (source) button 2. SEL (select/menu) button and VOL (volume) knob 3. Back to the previous configuration point; (automatic storage/preset station search, automatic search) 4. Short press button display clock in all mode. In USB mode, Short press to select All info/Elapsed time/File info/Track info/clock operation. Press and hold button turn off illumination on panel and touch any button to turn on illumination. 5. Folder up 6. Folder down 7.
FUNCTION Press the Volume knob and Rotate to select Audio/Display/Tuner/Clock/Beep/ Animation/Demo mode function. Press the Volume knob again to Select desire function mode. AUDIO MODE • Press the Volume knob and Rotate to select SW Level/Manual EQ/Q factor/ Preset EQ/Bass boost/Loudness/Subwoofer set/Fader/Balance/X’Over/DTA Setting/Car type. • Press and hold Volume knob to selet 2 way/3 way X’Over mode. SW LEVEL Press the Volume knob and Rotate to select -13 ~ +13 level.
X’OVER Press the Volume knob and Rotate to select Tweeter/Front HPF/Rear HPF/ Subwoofer LPF. TWEETER Press the Volume knob and Rotate to select Frequency/Gain left/Gain right. FRONT HPF Press the Volume knob and Rotate to select Frequency/Gain. REAR HPF Press the Volume knob and Rotate to select Frequency/Gain. SUBWOOFER LPF Press the Volume knob and Rotate to select Frequency/Gain/Phase. DTA SETTING Press the Volume knob and Rotate to select Position/Distance/Gain/Data Reset/ Delay Unit.
SPECTRUM Press the Volume knob and Rotate to switch ON/OFF. SPECTRUM Press the Volume knob and Rotate to switch ON/OFF. ID3 TAG Press the Volume knob and Rotate to switch ON/OFF. VERSION Press the Volume button to check software version. TUNER Press the Volume button to select Local Seek/Mono Set/Regional/RDS Set. LOCAL SEEK Press the Volume button to rotate switch ON/OFF. MONO SET Press the Volume button to rotate switch ON/OFF. REGIONAL Press the Volume button to rotate to select country regions.
Set the clock (CLK) 1. To display the Time press the CLK button. 2. To set the time, press and hold the CLK button and the time will start flashing. 3. Press the or button on the front panel or on the remote control to set the time. 4. Press the CLK button and the minutes will start flashing. 5. Press the or button on the front panel or on the remote control to set the minutes. 6.
GENERAL OPERATION Integrated Microphone For voice reception when making a call using the hands-free system. Auxiliary Input Connector 3.5mm auxiliary input stereo is designed for devices with line output 3.5 mm or hearing aids. Reset System The RESET button is used to reset all factory settings parameters, this function can be used when the LCD screen does not work properly or if the sound is distorted, or when some of the controls are disable.
To Store/Recall Preset Stations The radio can store 6 pre-set stations for each band (AM1, AM2, FM1, FM2 and FM3) for a total of 30 preset stations. Memorize a station • Turn the radio on and select the desired band and station. • Select a station by or button. • Press and hold the desired preset button (numbered 1-6 on the face of the radio) for more than 2 seconds to save the station to that preset number. To recall a preset station • Select the desired band.
EJECT/USB To eject a USB device, press USB device. the button to stop playback, then remove the Play/Pause Press the (play/pause) button to pause or resume playback Next/Previous Track • To play the next track, press the button. • To play the previous track, press the button. Fast Forward/Backward • To fast forward, press and hold the button. • To fast backward, press and hold the button.
Track/Folder Navigation • During a disc, USB mode, press the 5/-10 button to go backward 10 tracks. Press the 6/+10 button to jump forward 10 tracks. • During a MP3 disc, USB mode, press and hold the 5/-10 button to go back the previous folder. Press and hold the 6/+10 button to go to the next folder. You can repeat this function depending on the number and level of folders. • These buttons have no this function if the USB device has no folders. Select the track or file to play in MP3 format a.
4. When pairing is complete, the mobile phone audio will automatically transfer to the ship/car audio system whenever a call is made or received, or when the mobile phone plays music. Make a Call • To make a call, dial the call directly from the paired mobile phone. • To make a call with this Wireless BT hands free system: a.
REMOTE CONTROL Name of buttons and location 1. (Power ON/OFF) Button switched on 2. VOL +/VOL- (volume up/down) 3. Band button, (reply call) 4. button: Tune down, seek down; Track down, fast reverse 5. SEL (selection) button 6. button: Tune up, seek up; Track up, fast forward 7. Mute/DEL (Delete) button 8. CLK (clock setting) button, (end call) button 9. button: preset station 1 button, keypad 1 10. INT (intro) button, preset station 2 button, keypad 2 11.
Remove Insulating Sheet The remote control comes with an insulating sheet attached to the underside of the remote control, as illustrated on the right. The remote control will not work until the insulating sheet is removed. Replace Lithium Battery Cell 1. When the lithium cell battery becomes weak, replace it as illustrated on the right. 2. Press and hold the movable block in the direction indicated by arrow 1.
Remote Control Operation Position the emitting window of the remote control toward the sensor window of the unit. • The operation angle for front panel remote control reception is about 30 degrees. • The distance between the emitting window of the remote control and the sensor window of the unit should remain less 5 meters. • Cell leakage may cause damage to the remote control. • Do not throw cells into as this may cause an explosion. • Keep battery cells out of reach of children.
Radio 1. Much noise in broadcasts. • Station or signal is too weak. Select other stations of stronger signal level. 2. The antenna cable is not connected. • Insert the antenna cable firmly into the antenna socket of this receiver. 3. Preset station is reset. • Battery cable is not correctly connected. Connect the battery cable to the terminal that is always live. Scan the QR code to download the PYLE App.
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.