VIDEO PLDTVN65
It is prohibited in law if you watch TV or other multimedia programs while driving. So for your safety, please do not watch programsor operate the instruments. The system is designed to aid you to back cars, we will not take Any responsibility if there is an accident when backing. There is laser in CD changer. There will be possibly an exposure of harmful laser if try to operate or adjust or make a performance control. Do not open the CD changer or try to make any change.
Brief Introduction Thank you for purchasing this series of high quality AV products for automobiles. This product is a multi-function system developed by our company and special for high-level cars, business vehicles and special-use vehicles and has a car-carried control center concentrating entertainment, audio-visual, radar distance test, rear view and TV as a whole. This product also adopts professional car-carried suck-up DVD chip and can play DVD, MP3, VCD and CD.
2.6 kg 16:9 6.5 inches diagonal Weight Screen size Resolution 1200 234 pixels Dot pitch 0.136(H) 0.416(V) 2.1.2 Performance parameters Parameters Items FM/AM modulation parameters FM:87.5-108MHz AM:522 1611Mhz Modulation Phase-locked loop frequency modulation Display Panel LCD or OSD Memory capacity Seeking FM:16 AM:8 Automatic/by hand TV parameters VHF-L 48.25 Band 170.00MHz VHF-H 170.00 UHF 450.00 450.00MHz 863.
VCD parameters Video output 1 Vpp Video system NTSC (default) or PAL DVD parameters Disc 12cm DVD/VCD/CDMP3/CD-R SNR >90 dB Dynamic area >90 dB Distortion <0.05% Definition >500 TV system PAL/NTSC Amplifier parameters Test voltage 13.8V Maximum power output 50W 4 4 Full power output 25W 4 4 Speaker resistance 4 Tone can be 4 8 Bass 100Hz 12dB Treble 10kHz 12dB 2.
System Installation 3.1 Installation key points The product is specially designed for 12V vehicle, if installed in other vehicles, please install power Changer. To avoid short-circuit, it is strongly suggested to disconnect accumulator cathode before installation. This product should not be used without fuse. Do not connect with the mains directly with that of other electrical equipments.
-5- A/P Green BATT+ Yellow ACC Red GND Black BRAKE Blue/white BACK Blue Purple/Black Purple Right Back White/Black White Left Front Gray/Black Gray Right Front Green/Black Green Left Back Radar Input (Optional) Lens Input GND VCD changer Cable VCD changer Red CD AUDIO OUTPUT/R White CD AUDIO OUTPUT/L DVD VCD output 1\Antenna control is height effective 2\Amplifier control is height effective 3\Cassette should be grounded Caution: CD Audio input L (White) CD Audio input R (Red)
, Introduction to buttons 4.
4.
System operation instruction 5.1 Turn off /start system Press key (>2S) for 1 second to turn off the power of the system, pressing it once again will start the system automatically and restore to the last used status. 5.2 Volume control In the volume adjusting mode, press key weaker when press + , the volume will get louder and get . The volume during adjustment will be displayed on the screen (min. 0, max.
5.3.1 LCD Screen Setup Press SET to enter into menu setup, press or BRIGHT :32 COLOUR:22 CONTR :25 ANGLE :30 VIEW :WIDE (18) to select LCD screen setup, press (18) vertically to confirm into LCD screen setup. The screen will display as the right picture. The setup of brightness, color, contrast, angle and screen view (wide/zoom/center) can be done respectively. Press or or (18) to select up and down, the selected menu will become pink. Press (18)to make setup. Press SET again to exit system setup.
Or (18) to make setup. Press SET again to exit System When the blue screen is set to ON , and no visual signal is input, the screen will display in blue. Note: 5.4 Time setting Press SET to go into System Setup (refer to 5.3.3 in detail), and select TIME ADJ, press TIME ADJ (18) vertically to confirm 12:00 entering into time setup mode. The screen will display as the right picture. Press or (18) for time adjusting, press HOUR and MINUTE.
Press the digital keys (1~8) on the remote board, directly play the corresponding pre-stored radio channel; Volume adjusting please refer to 5.2; Select other functions(AV,TV,DVD,CDC) to stop playing radio. 6.2 Frequency Switch Press button BAND, you can choose FM(FM1/FM2) and AM. 6.3 Searching station A. Manual search Press or , tune the radio frequency forward and backward by 0.
,TV operation 7.1 TV play Press TV button to start TV signal receiving. Volume adjust refer to 5.2 Select other function( AV\Radio\DVD\CDC) to stop playing TV. 7.2 Receive preset TV stations Press TV button to watch TV, press or for playing preset next TV station or last TV station. Press number button(0-9) system will switch to that TV station after 3 seconds. Press button(0-4), screen will display X within 3 seconds, system will switch to XX , press once again the button channel automatically.
making the TV channel No. you want to store blinking and pressing M once again in 3 seconds, which will store the TV channel into the corresponding Number. This machine can pre-store 40 channels. , DVD operation 8.1 DVD playing Press key DVD, play DVD. Press DVD again or press OSD on the remote board to change to display OSD information. Press key M or TITLE on the remote rod to select captions. Press key S or LANGUAGE on the remote rod to select language. Press key A to return to DVD playing menu.
8.5 Track switch Under DVD mode, press BAND to change the sound channel. There are 3 selections (L/L, R/R, L/R) for sound channel change; the sound channel status will be displayed on the screen. If it is stereo(L/R) , the display will disappear after 3 seconds. , CDC operation 9.1 CDC playing Press key CDC, play CDC. Press CDC again or press OSD on the remote board to change to display OSD information. Select other functions (AV, TV, Radio, DVD)to stop CDC playing. 9.
9.6 CD changer operation 9.6.1 Insert discs Place the box with the side which has CD symbol upward. Draw out plate one by one to stop positions. Place discs on the plates in sequence. Push forward the plates into box until you hear a sound of click. To avoid accidental failure, place only one disc on one plate. 9.6.2 Remove discs Draw out disc plates out of CD changer to stop position, take out of discs with hands.
CAUTION: If in any case, the CD changer can not be draw out, press RESET . button and push the CD changer inside with strength, then press ejection button , AV operation 10.1 AV play Press AV button, start playing AV select other function(TV Radio DVD CDC),stop playing AV. Note: The AV input channel is commonly used with car-backing scene, if you use AV function, please set the BACK in Sys Setup to OFF (refer to 5.3.3 in detail) . 10.
, Necessary Disc machine installation In Example of Panasonic DP88 11.1 Appearance 11.1.1 CD changer C B A H V Door Angel Adjust Screw There are two angel adjust screws for both sides. Reset Compact disc area Eject 11.1.2 Compact disc and tray Compact disc inserting direction Tray LA ITA IO c UD Dis D IG CO MP AC T CAUTION Do not use a disc with 8cm diameter. Tray should be placed in the right position before inserting compact disc.
11.2 Installation guidance 11.2.1 Installation location When the temperature in car is too high, do not install this instrument on rear undercarriage to avoid the problems, in case it is caused by the contact with it. The following locations also should be avoided, Direct sunshine hot air from heater or other high temperature places. Not safe or heavily vibration. Too much humid, dirty or dusty. 11.2.
Vertical installation Vertical installation as shown below Incline angel <10 degrees (as shown below) Place screws in same positions in both sides (as shown below) <10 degrees A H B C V 11.2.4 Typical horizontal installation Use a hexagonal bolt with 2 washers(M4 8mm) Fix left and right installation trays onto host instrument.
Choose position to install fix trays with double sided adhesive tape. C B A H V Double sided adhesive tape 2 Tray 2 Cut a small cross on carpet in the position, which is right towards the M5 bolt on tray. Carpet Tray 2 Fix both tray and tape onto installation plate under carpet.
Use 4 hexagonal bolts(M5) to install the equipment onto the 4 holes on carpet. 4 AA HH CC BB Exagonal bolts(M5) VV Carpet 11.2.
11.2.6 The relations between angles and installation holes. H B C V A B V V C C B C B A H V A A H H Right tray Left tray The above figure has explained clearly the relation between installation holes and installation tray (left and right) angles. There are marks that show the installation angles. Please choose proper holes according to your installation angle.
12.1.2 Sensor's installation position 50-70cm 60-80cm According to the quantity installed, the positions can be as follows 25cm 25cm 30-35cm 30-35cm 63cm 63cm Remark: The final installation position can be adjusted slightly according to you car dimensions. 12.1.3 the requirements and method of installation Sensors should be inserted vertically into rear bumper as the arrow's direction. Any direction's inclination will affect the usage. Vertical Horizontal 12.
When radar backing car module is connected and you only connect 0.8M left (right) sensor, monitor will only display left (right) radar signpost, and for right(left) (yellow), there Is only ordinary signpost. When radar is connected, all 0.8M sensors connected too monitor will display radar signpost as The right picture. 12.2.2 Display of radar detection When the distance between radar sensor and barrier is more than 1.6m bea FAR there will on screen bottom. When the distance is less than 1.
Detection can be affected by: Smooth When in a smooth slope, signal can be reflected out. When in the near of a Smooth global object smooth spherical object, signal can be reflected out. When in the near of a sound Sound absorption cotton like object absorption cotton like object, signal can be absorbed greatly. After installation, please first Confirm the function, then use. XIII Precautions 13.1 Precautions when using the product Don't operate this product when driving.
13.2 Precautions on CD Dirt, dust, scratching and bended disc will result in operation error. Don't place the disc on the object with edge. Don't scratch the disk. Don't bend the disc. The disc should be taken out when it is not in use. The disc should not be placed at the following places The places in straight sun shine. The dirty, dusty and damp places. The places near the heater of automobiles. On the seat of automobiles or the plate of instruments.
Possible cause Problem Solution No sound The speakers is damaged. Replace with new peakers No image The disc is not put in the proper position. Put the side with label upward on the tray. The disc is dirty or damaged. Try other discs. Operation is failure. The sound skips The functions are locked Pull out the power plug, and insert after 10 seconds. The disc is dirty or damaged. Try other discs. The master control unit is not properly mounted. Ensure the master control unit is fixed firmly.
