Warnings • • • • • • • • • • • • Read these instructions and keep them for future reference. Carefully follow instructions and follow directions carefully. Keep the amplifier dry, as some liquids may contain minerals that corrode electronics circuitry. Clean amplifier housing only with a slightly damp cloth. No chemicals or solutions. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
Testing & Connections After all the connections have been made. turn on your stereo and listen for the amplifier to turn on. If there are any unusual noises from the speakers then turn the system off and recheck all the wiring. After you have connected your radio or equalizer to the amplifier, you may adjust the gain control to match the output level of your radio: (A) Set the volume control on your radio to 2/3 position. (B) Adjust the gain control for an average listening level.
PLMRA210BT - System Layout PLMRA210BT 1 RCA (Low Level Input) 2 Input Gain Control 3 Bridging Capability 4 Speaker Connectors (High Level Input) 5 Power Supply Terminal This unit Is provided with RCA Input jacks. Couple the RCA Input with the car stereo or equalizer outputs using RCA type connector cables. These are NOT Your amplifiers volume controls. They are a sophisticated device which is to be utilized when matching the Input signal of your head unit or equalizer to their amplifier.
BATT +12V GROUND REMOTE 6 Power on LED 7 Protection LED 8 Power Fuse 9 Speaker Terminals 10 11 Crossover Frequency Circuit Crossover On/Off Switch Connect+ 12V DC power supply wire Into the terminal from the terminal of the fuse at battery. (Fuse preferably installed 1 foot within 1 foot from the battery). Ground terminal connect the ground wire to the chassis of the automobile, boat or other vehicle. Remote terminal connects the control wire which provides remote turn-on and power off.
Stereo Input Connection RCA Type Terminals High Impedance Low Level Inputs Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability. Stereo Input Connection - RCA Type The Elite Series Amps feature plated RCA terminals for low level input connections to match radios and equalizers with line level output. Couple the RCA input with the car stereo/equalizer output using RCA type connector cables.
Mono Input Connection - RCA Type Select Elite Series Amps may easily be bridged for mono operation by feeding the same signal to both LEF T and RIGHT Input terminals. The simplest way to achieve this is by using a Y-adaptor to connecting your car stereo output. Speaker Connection - Stereo Amp System Connect the output terminals to the corresponding LEFT and RIGHT Speakers. (Fig.
Speaker negative terminals on the amplifier are not used in the bridged mode. Bridging is done by using multiple channels of an amplifier to drive a common load. Bridging means that you will use more than one source of power to drive a load (speaker). The sources of power are the independent channels of the amplifier. Some users may automatically set the gain to maximum because they want their music loud, by doing so, they are also increasing the chance of burning out their amplifiers.
PLMRA210BT - Wiring Stereo Amp Connection Mono Amp Connection Elite Series Waterproof Amplifiers
PLMRA410BT - Wiring Stereo Input Connection RCA Input High Level - Speaker Level (BTL or Common Ground) Four Speaker Output Mode Floating Ground Type Elite Series Waterproof Amplifiers
PLMRA410BT - Wiring Common Ground Type Two Speaker Output Mode Floating Ground Type *High and Low impedance inputs cannot be used at the same time. Note: Elite Series Ampshave built-in short circuit protection. If you mistakingly connect any speaker wires to ground, or positive power ( +) and (-) Wires short together, the protection circuit will operate automatically and cut-off output.
PLMRA410BT - Wiring Power Connection Connect the speaker output terminals to the corresponding speakers. The speakers must be high quality and capable of handling high power. Separated return paths and strong wires are required. 1. Connect the B+12V pole of power supply directly to the battery(+) position terminal (In-line fuse 1 foot from battery). 2. Connect the GND pole of power supply directly to the (-) negative ground battery terminal or vehicle chassis. 3.
PLMRA430BT - Wiring Power Connection Elite Series Waterproof Amplifiers
PLMRA430BT - Wiring 4 Channel Input Connection Low Level Inputs 2 Channel Input Connection Low Level Inputs High Level Wiring 4 Channel Connection Floating Ground Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability.
PLMRA430BT - Wiring 4 Channel Mono Connection Low Level Inputs 2 Channel Connection Low Level Inputs 4 Channel Mono Connection Floating Ground Elite Series Waterproof Amplifiers
PLMRA430BT - Wiring 4 Channel Output Mode Bridged Dual Mono Output 2-8 Ohm 4 Channel Stereo Output Mode with Mono Bridged Subwoofer Output 4-8 Ohm Elite Series Waterproof Amplifiers
PLMRA630BT - Wiring Elite Series Waterproof Amplifiers
PLMRA630BT - Wiring Electrical Connection 4 Channel Inputs RCA Low Level Mono Input Connection 6 Channels Elite Series Waterproof Amplifiers
PLMRA630BT - Wiring Speaker Connection 6 Channel Output Mode 2-8 Ohm 2-8 Ohm Speaker Connection Mono Bridged Subwoofer Output Elite Series Waterproof Amplifiers
PLMRA830BT - Wiring Elite Series Waterproof Amplifiers
PLMRA830BT - Wiring Electrical Connection Multi Channel Input Connection Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability.
PLMRA830BT - Wiring 8 Channel Output Mode 2-8 Ohm Mono Bridged Subwoofer Output 2-8 Ohm Elite Series Waterproof Amplifiers
Elite Series Bluetooth Connection When searching for the amp via your smartphone or other Bluetooth-enabled device, the Bluetooth amp network name will appear as 'Pyle Amp' in your device list. The amp will not require a password to connect. Once successfully paired with your compatible Bluetooth-enabled device, you will be able to control music streaming ability into the Pyle amp. Choose from streaming audio to adjusting volume controls -- all from your device.
Mounting... When making electrical connections with your amplifier and vehicle battery, please take precaution and have a professional, or install under the supervision of a professional. Use the proper gauge wire for power and ground connections. Wire the amplifier directly to the car battery. For ground connection, use the shortest possible wire to a secure chassis ground. Wire the remote connection to the auto start lead of your head unit, equalizer, or power antenna.
Troubleshooting No output. Confirm that all terminal strip connections are secure and tight. Check both In-line and built-in fuses. Both the + 12V am the Remote terminals must have + 12V referenced to chassis ground. Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the amp).
Pyle Elite Series - Models & Specs Elite Series Waterproof Amplifiers
Elite Series Waterproof Amplifiers