PLR44MU OWNER’S MANUAL Mobile Audio System PLL Synthesizer Stereo Radio Automatic Memory Storing Full Detachable Panel Preset Equalization USB Interface SD/MMC Interface
INSTALLATION Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
INSTALLATION 6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. terminal to the dashboard. Spring Washer Hex Nut Metal Strap Mounting Bolt Plain Washer Tapping Screw Dashboard Tabs 10.
INSTALLATION fasten the unit to the factory radio mounting brackets supplied with your vehicle. Side View showing Screw Holes marked T, N Screw Factory Radio Mounting Bracket Screw Dashboard or Console To fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: the outer trim ring, sleeve and the metal strap are not used for method B installation.
USING THE DETACHABLE FRONT PANEL REMOVING THE FRONT PANEL 1. Press the release button ( ) on the front panel and pull off the front panel. 2. Keep front panel into the case. INSTALLING THE FRONT PANEL To install the front panel, insert the panel into the housing and make sure the panel is properly installed. Otherwise, abnormality occurs on the display or some keys will not function properly. Precautions when handling 1. Do not drop the front panel. 2.
WIRING CONNECTION ISO CONNECTION
OPERATION LOCATION OF KEYS 1. (release button) 2.PWR 3.9/ 4.7/MODE 5. SEL/VOL 6. AMS/SCH 7.LOC 8.Reset button 9.LCD 10.SD/MMC interface 11.USB interface 12.AUX IN 13. 0 DSP 14.6 DIR+ 15.5 DIR16.4 RDM 17.3 RPT 18.2 INT 19. 1 PAU 20. BAND/LOUD 21. MON 22.EQ 23.8/ 24.MUT 25.
OPERATION SWITCHING ON/OFF THE UNIT Press PWR button (2) to turn on/off the unit. FACEPLATE RELEASE Press release button (1) to detach the removable faceplate. SOUND ADJUSTMENT Press SEL button (5) shortly to select the desired adjustment mode.
OPERATION mode, the radio mode appears in the display together with the memory band and frequency. SELECTING THE FREQUENCY BAND At radio mode, press BAND button (20) shortly to select the desired band. The reception band will change in the following order: →FM1→ FM2→ FM3 → MW1→ MW2 SELECTING STATION button (3) or button (23) Press shortly to activate automatic seek function. Press for several seconds until “MANUAL” appears on the display, the manual tuning mode is selected.
OPERATION SD/MMC interface, the unit will search the MP3 files or WMA files in the card and start to play automatically. The operation is the same with the USB play operation described above. If in other mode, you can also press MODE button (4) to select SD/MMC mode. CAUTION： When there are important files in the USB Device or SD card, do not connect it to the main unit to play, because any wrong operation may cause files loss. And our company assumes no responsibility for this.
REMOTE CONTROL HANDSET(OPTIONAL) FUNCTION KEY & CONTROL - POWER Power ON/OFF Button - MODE Mode Botton(S,T,U,7,For MP3/WMA Operation) - TUNE/SKIP (8) Tune/SKIP Down Button(V,W,X,8 For MP3/WMA Operation) - 7/BND Band Select Button(When pressed shortly) - SCN Scanning Button(D,E,F,2 For MP3/WMA Operation) - PAU Pause Button (A,B,C,1 For MP3/WMA Operation) - SHF Shuffle Button (J, K, L 4 For MP3/WMA Operation) - DIR▼ DIR▼ Button - VOL▲ Volume Up Button (Character Select (A,B~8,9,0)For MP3/WMA Operation) - SEL
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 kHz) Maximum Output Power - Version V Current Drain - Version V - Power Version) RADIO Frequency Coverage IF Sensitivity (S/N=30dB) Stereo Separation : DC 12 Volts, Negative Ground : 178 (W) x 107 (D) x 50 (H) : ±10 dB : ±10 dB : 4x60 watts :5 Ampere (max.) For 2 Bands (Europe) FM 87.5 to 108 MHz 10.
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. Symptom No power Cause The car ignition switch is not on The fuse is blown.
