PLTS78DUB 7'' Single DIN In-Dash Detachable Motorized Touch Screen TFT/LCD Monitor w/ DVD/CD/MP3/MP4/USB/SD/AM-FM Bluetooth A2DP & AVRCP compatible USER MANUAL
To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
Content Precaution...................................... 2 Basic Operation .............................. 25 Safety Information......................... 3 Selecting Play Mode ........................ 25 Disc Note....................................... 4 On-Screen Display Function ............. 27 Installation .................................... 5 Digital Video Special Function........ 28 Electric Connection ...................... 9 Multi-Subtitle Language function....... 28 Remote Control .......
Precaution THANK YOU FOR PURCHASING THIS CAR DIGITAL VIDEO PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Disc Note Disc formats supported by this player Digital Digital Video Video Audio and Video Disc size 12 cm VCD VCD Audio and Video Disc size 12 cm CD CD Audio Disc size 12 cm MP3 MP3 Audio Disc size 12 cm Discs which cannot be played with this player Digital Video-RAM CDV CDG Handling and Cleaning Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs.
Installation NOTES: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Installation Installating the unit DASH BOARD METAL MOUNTING STRAP HEX NUT SPRING WASHER PLAIN WASHER CONSOLE TAPPING SCREW SLIDE BRACKET HOUSING HEX BOLT SCREWDRIVER TABS KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into left and right side of chassis as above illustration.
Installation How To Remove And Install The Front Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching The Front Panel Before detaching the control panel, be sure to turn off the power. 1).
Installation ATTACHING THE FRONT PANEL 1). First, insert the left side of the front panel into the main unit(SEE 1 ). (Note: the “Hollow ” point on the front panel must be attached into the “Bulge” point of the unit . ) 2). Gently push the right-down hand side of the front panel until you feel a “ Click” . (SEE 2 ) Bulge Hollow 1 2 Precautions Do not touch the contacts on the front panel or the unit body, since this may result in poor electrical contact.
Electric Connection WIRING CONNECTION RCH RED REAR RCA OUTPUT CABLE REAR CAMERA INPUT YELLOW SUBWOOFER GREY VIDEO IN YELLOW RCA CABLE LCH WHITE FRONT RCA OUTPUT CABLE FRONT RCA RED R VIDEO OUT YELLOW FRONT RCA WHITE L RADIO ANTENNA JACK ISO CONNECTOR PINK IGNITION SWITCH(B+) MEMORY BACK-UP(B+) RED BROWN YELLOW GROUND(B-) BLUE BLACK FRONT LCH SPK. REAR LCH SPK.
Remote Control 15 7 2 MODE 17 16 STOP 3 REDIAL MO/ST ZOOM 13 20 PAIR EQ CLK 24 21 OSD BAND 9 ENTER TITLE/PBC 23 A/PS VOL 11 VOL TOP RPT INT 1 2 3 10 5 4 SEL 12 RDM 6 AF 8 7 27 9 TA 4 SETUP GOTO +10 0 8 Ref # Button 5 1 LOUD MENU LO/DX 6 18 PLAY/PAUSE 19 22 14 MUTE 25 26 Function 1 CLK Press it briefly to view the clock time . 2 PAIR/ 3 STOP 4 SETUP Pr es s it to us e the BT fun ct ion , ref er to se e BT op er at ion .
Remote Control Ref # Button 8 GOTO 9 / Function Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. In BT menu, it serves as the asterisk button on your mobile handset. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button 23 This button is used to confirm selections and settings within many ENTER of the menus in the OSD system. In DISC mode, press it to reverse rapidly 24 25 0-9 0/TA 9/AF 26 +10/ 27 1-6 Use to input numerical values during programming, with the GOTO button, or to directly select a track to play . In Radio mode, (when the RDS engaged,), 0 serves as TA function, 9 serves as the AF function .
Basic Operation POWER ON/OFF Touch the “OFF” ICON on screen to turn the unit off . Press the“ ” onthe front panel to turn It on, press it again to turn off . FIG.2 LOADING/EJECTING A DISC Loading a Disc 1. Press the POWER ( ) button on the front pane to turn the device on . Adjusting the viewing angle . When the monitor does not move, you press button on the panel to turn the monitor upward or downward at fine steps to get a desired viewing angle . 2.
Basic Operation When the monitor turns downward to a certain angle, it will draw in . Touch the “SET” ICON on touch screen to enter the setting mode, the message will display like following : FIG.6 BRIGHTNESS CONTRAST COLOR TFT Monitor Adjustment In Radio mode, touch the“ RADIO ” icon or In media mode , touch the range to enter the home menu, the message like following as below. (1) (2) 15 Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.
Basic Operation SETTING WALLPAPER in wallpaper mode, you can select the among of “AUTO, GREEN, YELLOW, RED, LIGHT BLUE, BLUE, PINK ” . When you select the “AUTO” item, the player will change the background automatically . BALANCE: R 0-10 to L 0-10 . Adjust sound balance between left and right speakers . FADE: F 0-10 to R 0-10 Adjust sound balance between front and rear speakers . SETTING LED LIGHT (3 COLORS) In LED COLOR mode, you can select the color among of “Auto, Blue, Red, Pink ” .
Basic Operation Setting Audio Mode Rear View Camera In any modes, touch the “EQ” range on the touch screen (or press the EQ button on remote control) to select one of the preset sound modes: ROCK/POP/ JAZZ/CLASSIC/USER . When connecting the rear view camera the mirror image of the rear view is automatically displayed on the monitor when you change the gear to the back position. (Note: additional monitor can not display the image.) EX.: In RADIO mode 87.
Control Panel UNIT KEYS 11 4 OPEN MIC /CH1~6 VOLMODE VOL+ PUSH SEL IR 1 2 18 12 13 14 TA/AF MU/PTY PAIR BND AUX IN USB IN 9 8 7 3 10 5 6 15 Control Panel 16 17 Front Face of Chassis after remo ving Control Panel 1. OPEN or BUTTON To slide the monitor out and stand it up or into the monitor slot, press this button; To adjust the angle of the monitor, long press this button . 2. VOL KNOB & SEL BUTTON In normal mode, VOL knob is used to increase or decrease the volume.
Control Panel 4/10. >>|/ and |<>| button can automatically search down or up for an available station beginning from the current frequency; Briefly pressing |<< or >>| button can manually search down or up for a your desired station beginning from the current frequency.
Control Panel 8 /CH 1-6 (RADIO PRESET) BUTTON A) In Disc Playback Mode Press this button to pause playback, press it again to resume playback. B) In Radio Mode Press this button repeatedly to preset station. With this system a total of 30 stations can be stored in the memory . Each band store up to six preset stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2 (MW2) band.
Touch Screen Operation Start Searching For a Station RADIO OPERATION Manual Search During Radio mode, briefly touch “ ” to increase frequency by one step of channel spacing. Briefly touch “ ” to decrease frequency by one step of channel spacing. Automatic Search During Radio mode, touch and hold (for more than 2 seconds ) either “ / ” ICONS to start search for a radio station automatically.
Touch Screen Operation Storing and Listening to a Memory station Automatic Preset Setup In Radio Mode, touch and keep (for more than 2 ’ S) the screen of “ APS ” range to active automatic station storage. The radio searches within the current frequency band, e.g. FM1, for the stronger signal level until the search cycle has finished . The six strongest stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set . Setting Memory 87.
Touch Screen Operation ADJUSTABLE ITEMS: TA Traffic Announcement (Priority For Traffic Information) REGION SET Touch to switch the REGION function ON and OFF . PI SET Touch to change between PI MUTE and PI SOUND . REG FUNCTION at certain times some stations divide up their programs into regional programs with varying content . REG ON : the message “REG ON” will appears in the display for a few seconds . Note : - the display capacity is limited .
Touch Screen Operation Touch the AF section on touch screen or swing and keep the SEL knob in the TA/AF direction for about 2 seconds , the AF function is activated. The AF symbol appears in the display . When the AF function has been switched on, the radio continuously tests the signal strength of the AF frequency . The test interval for each AF frequency depends on the signal strength of the current station and varies from a few minutes in the case of weak signals.
Touch Screen Operation Media Operation To search the disc with numbers In any modes, repeatedly press MOD button on front panel to enter the media play mode . The message will display as below : (When Parking Brake is applied .) MENU TITLE PBC To display the root menu on stored Digital Video discs . In Digital Video mode, touch to display the title menu. In VCD mode, touch to switch the PBC ON and PBC OFF.
Touch Screen Operation BASIC OPERATION Note: when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right . Stopping Play Touch ICON to stop the unit playback. Touch to start play. Pause (still picture) Touch during playback to temporarily pause play. Touch again to return to normal playback.
Touch Screen Operation seconds part of each track/chapter on disc. (Touch it again to cancel this mode) FOR VCD : Touch the screen of the “INT” section (or longer press the 3/INT button on the remote control ).
Touch Screen Operation ON-SCREEN DISPLAY FUNCTION OSD During playback, touch the screen of the OSD section, it will display the following as below : 1. Digital Video: A.Touch or Press OSD for first time: 2.Example for VCD/SVCD/CD: A.Touch or Press OSD for first time: VCD TRK 1/19 A PBC C 0:01:36 B.Touch or Press OSD for second time: VCD TRK 1/19 A PBC C -0:06:06 Digital Video TT 01/01CH 04/31 C 0:02:06 C.
Touch Screen Operation Digital Video Special Function 1. Multi-subtitle Language Function (for Digital Video Only) 3. Title Menu Function During Digital Video playback. Touch the SUBTITLE section on touch screen(or press the SUBTITLE on the remote) . Each time the button is pressed or touch, number of the subtitle language changes in sequential order. Notes: - The language number is different according to the disc. - Some discs only contain one subtitle language.
Touch Screen Operation SYSTEM SETUP MEDIA SETUP MENU USING THE MENU SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT EXIT EXIT 1. IN disc model Touch the screen of “ ” range or press the SETUP button on remote . 2.The SETUP menu is displayed. 3.Touch directly the desired item to select the preferred item . buttons . Or by using the / / / 4.
Touch Screen Operation SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT 4:3PS 4:3LB 16:9 EXIT 16:9 ----- EXIT 4:3 Letter Box 4:3 Pan Scan TV DISPLAY SETUP This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set. Normal/PS (For 4:3 TV) Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.
Touch Screen Operation SYSTEM SETUP LANGUAGE SETUP ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT RESTORE EXIT EXIT DEFAULTS Selecting the DEFAULT item and confirming RESTORE will return ALL personal settings you have made, including radio and TV presets, to the factory default settings.
Touch Screen Operation VIDEO SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS EXIT EXIT DISC MENU LANGUAGE SETUP Select the preferred DISC MENU language by touching directly the desired language . CONTRAST- the contrast of the video signal (the dark portions of pictures).
Touch Screen Operation DIGITAL SETUP VIDEO SETUP 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS DIGITAL SETUP DYNAMIC RANGE FULL 6/8 4/8 2/8 OFF EXIT EXIT SATURATION- the saturation of the video signal (the vividness of the color) all above can be adjusted to your tasters . DYNAMIC RANGE CONTROL Select DRC and adjust the dynamic range of a Dolby Digital encoded program. There are 8 steps between full compression and off compression.
Touch Screen Operation AUX Operation On the front panel of this unit, there is an AUX IN jack, follow the diagram below to connect analogue replay devices(only for the Audio connect, if you want to connect the Video, please plug the RCA
Touch Screen Operation BT OPERATION IMPORTANT: 1). If the pairing can not be completed within approximately 2 minutes , whiles the pairing mode is activated, and you will need to reattempt pairing (See steps 2-5 above) . 2). After pairing is completed, if the BT ICON is stilling flash on the TFT , please follow the steps to reattempt pairing through your handset until the BT ICON remains solid on the screen. 1.
Touch Screen Operation ANSWER A CALL PLAY BT MUSIC After you hear the ring tone, a incoming telephone number will display on the TFT monitor . Touch the screen of “ ” range to listen or press the “PAIR/ ” button shortly on the remote control . In BT mode, repeatedly the MOD on the panel to select the “BT MUSIC” Mode .
Touch Screen Operation USB OPERATION Changing From DISC to USB Playback Mode If the disc present in the player is an Digital Video or VCD or MP3/WMA or MP4 disc, touch the screen of the “ ” range to enter the home menu, then touch the “USB” ICON to enter the USB mode . Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically.
Touch Screen Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . INSERTING THE SD OR MMC CARD . Label side facing upward Press REL button to detachable the panel Insert the memory card into slot with label side facing upward . Note: the mini card slot for GPS only. Press in till heard a “CLICK” REMOVING THE SD OR MMC CARD .
Touch Screen Operation MP3/WMA/JPEG/MPEG4 PLAY The unit is support MP3/WMA/JPEG/MPEG4 . When a disc is inserted into player, the following picture will appear on the monitor . The unit will play the first track automatically . You can touch to directly others mode (MP3/JPEG /MPEG4) to play . EX. : when the MP3 mode is selected . 2 1 Current type (highlighted bar) . [MP3] ITLE / SONG: TRACK 03 / 2 Current track (ID3 TAG display) . 001 WMA 002 1 Mp3 003 3 The current play mode(MP3).
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.0Vp-p 75 (1)DIGITAL-VIDEO Disc 5"(12 cm) single-sided, single-layer 5"(12 cm) single-sided, double-layer (2)Compact Disc (CD-DA, VIDEO CD) 5"(12cm) disc Audio Signal Output: Characteristics: 2ch&4ch line out (1)Frequency Response (2)S/N Ratio (3)Wow and Flutter 20 Hz - 20 KHz 90 dB (JIS) Below measurable limits For 2 Bands (Europe) FM 87.5 to108 MHz 10.
Troubleshooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.
