User Manual

ManualsBrandsPyle ManualsAmplifier & Speaker Kits5.25'' Waterproof Marine Speakers + 2 Ch. Rated Amplifier +Wireless BT Audio Controller- ATV, UTV, 4x4, Jeep, Wired RCA, for Boat Stereo Speaker & Other Watercraft (1000W)

Questions? Issues?

We are here to help!

Phone: (1) 718-535-1800

Email: support@pyleusa.com

5.25'' Waterproof Marine Speakers

+ 2 Ch. Rated Amplifier +Wireless BT Audio Controller

ATV, UTV, 4x4, Jeep, Wired RCA, for Boat Stereo Speaker

and Other Watercraft (1000W)

PLUTV58BKA

Summary of content (8 pages)

PAGE 1
PLUTV58BKA 5.25'' Waterproof Marine Speakers Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.com + 2 Ch.
PAGE 2
PRECAUTIONS • This unit is designed for negative ground 12-14.50 Volts (DC) operation only. • Use speakers with an impedance of 4 Ohms • Avoid installing the unit where: • It would be subject to high temperatures, such as from direct sunlight or hot air from the heater. • It would be exposed to rain or moisture. • It would be subject to dust or dirt.
PAGE 3
+ 12V = POWER SUPPLY NOTES ON THE POWER SUPPLY Connect the BATT terminal to the positive pole of the battery with a lead cable and add a fuse into the power cable in a distance of not more than 30 cm from the battery. The lead cable’s diameter should be at least 4 mm’ for a length of 3 m and 6 mm” for a length of 6 m. • Connect the +12V power input lead only after all other leads have been connected. vehicle/or boat.
PAGE 4
PROTECTION CIRCUIT INTERFERENCE This amplifier is provided with a protection circuit which operates in the follow- All cables can source and create interference. The power cable and Cinch/RCA audio cable are very prone to interference; the remote cables are less prone. There is often interference caused by the generator (piping), ignition (cracking) or other vehicle/or boat electronic parts. Most of these problems can be eliminated by correct and careful cabling.
PAGE 5
PLUTV58BKA Speaker Installation WIRE DIAGRAM AUX Input Line out-L Line out-R Speaker Mounting suggestion as below: STEP 1 USB STEP 2 Remote Out (Blue) Fuse: 5A STEP 3 STEP 4 -BLACK +YELLOW DC12V(-) Grounded to metal chassis STEP 5 Wire Color Yellow Black White Red Red Blue Description Battery (+), 12dc Battery (-), Ground Line out - L Line out - R ACC REMOTE ACC Remote In (Red) DC12V(+) Grounded to metal chassis WIRELESS BT PAIRNG AND CONNECTION Power: Press and hold the power button to
PAGE 6
c. Disconnected BT after 10 minutes, you need to process BT connection steps (above) to reconnect BT again. d. If the other device occupied the BT during this period (10mins), you need to process BT connection steps (above). INSTALLATION (SEAMLESS FLUSH MOUNT) PLAYING MUSIC • 70mm/2.76” (Overall Diameter) 1. Press and hold for 3 seconds to Power ON or OFF. • 96mm/3.7” (Overall Diameter) • 76mm/3.0” (Mounting Hole Diameter) 2. Short press to play music or pause. 3.
PAGE 7
PLUTV58BKA WIRE DIAGRAM UTUTP ck) L-O e+Bla it ( Wh R- Remote (Blue) Line out-L Output (L) AUX Input Black DC12V(-) Grounded to metal chassis, or directly to negative polarity of battery. -BLACK A e: 5 Fus Output (R) Line out-R W AUX Input LLO +YE USB +12v Red DC12V(+) Recommended wiring with fuse (parts are not included) 12 www.PyleUSA.
PAGE 8
Amplifier Technical Specs: • Amplifier Type: 2-Ch. Audio Component • Power Output: 1000 Watt MAX • 2 x 50 Watts RMS @ 4 Ohm • 2 x 150 Watts MAX @ 4 Ohm • Marine Grade IP-45 Rating • T.H.D：≤ 1% • S/N Ratio：≥ 80dB • Channel Separation：≥ 65dB • Fuse: 15A • Power: DC 12V • Amp Dimensions (L x W x H): 6” x 3.86” x 2.36” –inches BT Control Unit: • Simple & Hassle-Free Pairing • Instant Wireless Audio-Streaming Receiver • Works with All of Today's Latest Devices Smartphones, Tablets, Laptops, Computers, etc.