PRECAUTIONS • This unit is designed for negative ground 12-14.50 Volts (DC) operation only. • Use speakers with an impedance of 4 Ohms • Avoid installing the unit where: • It would be subject to high temperatures, such as from direct sunlight or hot air from the heater. • It would be exposed to rain or moisture. • It would be subject to dust or dirt.
REMOTE TURN-ON CONNECTION The amplifier is turned on by applying +12V to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna" lead from the vehicle/or boat stereo resources which will provide the +12V only when the stereo resources is turned on . If the car stereo does not provide an "AutoAntenna" lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the vehicle’s/or boat’s fuse block.
+ 12V = POWER SUPPLY Connect the BATT terminal to the positive pole of the battery with a lead cable and add a fuse into the power cable in a distance of not more than 30 cm from the battery. The lead cable’s diameter should be at least 4 mm’ for a length of 3m and 6mm” for a length of 6m. REM (ON/OFF) REMOTE CONTROL Connect the REM terminal to the automatic antenna connector of your vehicle/or boat radio.
NOTES ON THE POWER SUPPLY • Connect the +12V power input lead only after all other leads have been connected. • Be sure to connect the ground wire of the unit securely to a metal part of the vehicle/or boat. • Loose or faulty connection may cause amplifier malfunction • REM: The unit is turned on by applying +12 Volts to this terminal. This terminal does not draw heavy current like the tow Power Terminals so a thinner connecting wire is acceptable. Standard 18 GAUGE is fine and the standard color is red.
No Sound: • Speaker cable or speaker plug are not connected correctly. • The plus and minus wires of the speaker cable have contact, thus eliminate the short circuit. If you use Pay attention only 4 ohm load speaker is allowed. No 2 ohm or less impedance speaker connection is allowed. Poor Sound Quality (Distortions): • The speakers are overloaded, therefore turn down the volume level and check the volume control positions.
Gold Plated spade terminal are free of corrosion and have the lowest contact resistance. • Should all these meaures be without any success, the use of a ground loop isolator may solve the problem. PLUTV60CH Speaker Installation Speaker Mounting suggestion as below: 1/4” Hex key 5/16” Hex key Diagram A 45° Diagram B Step 1: Removing the top half of clamp Put the PLUTV60CH speaker in a safe place. Using the 1/4” Hex key, remove the top clamp bolts.
Step 4: Securing clamp bolts Using the correct rubber pads (labeled for O.D.) install on both top and bottom half of clamps. 3.15” x 1.2” x 0.2” rubber pads for 1.75” O.D. 3.15” x 1.2” x 0.08” rubber pads for 2” - 3” O.D. Using the 1/4” Hex bit socket hand tighten the bolts evenly (both sides should have the same spacing between bolts). Step 5: Option for adjustable PYLE logo---Unbolt the screws first, adjust the logo direction, then re-fix screws.
Amplifier Technical Specs: • Amplifier Type: 2-Ch. Audio Component • Power Output: 1200 Watt MAX • 2 x 50 Watts RMS @ 4 Ohm • 2 x 150 Watts MAX @ 4 Ohm • Marine Grade IP-X6 Rating • T.H.D：≤ 1% • S/N Ratio：≥ 80dB • Channel Separation：≥ 65dB • Fuse: 15A • Power: DC 12V • Amp Dimensions (L x W x H): 6” x 3.86” x 2.36” –inches Marine / PowerSports Tower Technical Specs: • Power Output: 1200 Watts • Marine Grade Waterproof Rating: IP-X6 • Speaker Size: 6.
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.
