User Manual

PLUTV65BTR Installation
Speaker Mounting suggestion as below:
Step 1: Removing the top half of clamp
Put the PLUTV65BTR speaker in a safe place.
Using the 1/4” Hex key, remove the top clamp bolts.
Step2/3: To adjust mounting clamp angle and speaker position
Diagram A is to show there are four round pins underneath the bottom
base of aluminum die cast clamp, which can be inserted and xed to four
round notch holes on top of plastic cabinet as diagram B shows by every
45 degrees adjustment either at clockwise or counter clockwise direction.
Through such design, user can change the angle of swivel clamp, use the
5/16” hex key to loose the center screw a little bit and lift the bottom clamp
to twist speaker angle by every 45 degrees to get the optimal angle you
want. Then re-making sure the pins on base of bottom clamp are inserted
and sits on notch holes on top of plastic cabinet at and seamlessly.
Then re-tighten the center hex screw to secure the bottom clamp strongly.
Step 4: Securing clamp bolts
Using the correct rubber pads (labeled for O.D.) install on both top and
bottom half of clamps. 3.15” x 1.2” x 0.2” rubber pads for 1.75” O.D. 3.15” x
1.2” x 0.08” rubber pads for 2” - 3” O.D. Using the 1/4” Hex bit socket hand
tighten the bolts evenly (both sides should have the same spacing
between bolts).
Step 5: Option for adjustable PYLE logo---Unbolt the screws rst, adjust the logo
direction, then re-x screws.
2
www.PyleUSA.com
PLUTV65BTR Wiring
1. Connect the RCA plugs (red/white) to an external amplier for audio output.
2. Connect the ACC wire (red) to the accessory power of the vehicle as ON/OFF
switch of the speakers.
3. Connect the remote out wire (blue) to an external amplier as ON/OFF switch
of the amplier.
Remote Control
3
www.PyleUSA.com
Remote Control Functions
• 10 static colors for choose with 8 kind of brightness which can be adjusted up &
down.
• 3 colors ash, 4 colors strobe, 7 colors fade, 7 colors smooth, all modes can
adjust the brightness and speed.
• In static color mode, the brightness can be adjusted up and down.
• 6 kinds of EQ mode.
Features:
• Pro Audio PowerSport Speakers with RGB Lights
• Amplied (Active) Speaker System
• Wireless BT Music Streaming Ability
• Bridged Sound System: (2) x 6.5'' Woofers + (2) x 1'' Tweeters
• Marine Grade Rated Construction
• Weatherproof & Water-Resistant Housing
• 2-Way Full Range Stereo Sound Reproduction
• Built-in Digital Sound Processing Amplier
• Integrated Speaker Power & Wiring Harness
• Compact Size & High-Powered Output
• Impressive Bass Response
• Aux (3.5mm) Input Jack
• Pre-Amp RCA Out to Any OEM/Factory-Made Mono-Block/Full-Range Amplier
• Connect & Stream Audio from External Devices
• Sleek Design, Machine Molded Speaker Cabinet Housing
• Rugged, Universal Mount Bracket Design for Roll-Bar/Roll-Cage
• Used for O-Road Outdoor Vehicles: ATV, UTV, 4x4, Jeeps, Marine Watercraft
BT Connectivity:
• Simple & Hassle-Free Pairing
• Instant Wireless Audio Streaming Ability
• Works with All of Today’s Latest Devices (Smartphones, Tablets, Laptops, etc.)
• BT Version: V5.0
• BT Network Name: ‘PyleUSA’
• Wireless Range: 30+ ft.
• *BT Receiver Module Built-Into Amplier of Main / Active Speaker
4
www.PyleUSA.com
12V wire harness connection
LED wire
LED wire
Black -
Gray +
AUX input
(2)
ACC wire
(red)
(1)
Audio output
(3)
Remote out
wire (blue)
Ground wire
(black)
Battery wire
(yellow)
DC12 (-) grounded to
metal chassis, or directly
to negative polarity of battery
DC12 (+) extention
power cable with fuse
holder (not included)
POWER OFF/ON
FLASH
STROBE
FADE
SMOOTH
STATIC COLOR CHOICE
BRIGHTNESS &
SPEED UP/ DOWN
NORMAL
JAZZ
POP
COUNTRY
ROCK
CLASSIC