PLVW65M OWNER'S MANUAL TFT MONITOR www.pyleaudio.
INSTALLATION The monitor (Fig.1) can be installed on the bracket (Fig.2). You can mount the unit according to the following steps. Monitor Slot 2 Mounting Bracket Slot 1 Fig.1 Position Plate Screw Cover 1 Rotation Top Screw Cover 2 Base Rotation Base Fig2. 1. Insert the position plate on the bracket into the slot 1 on the mounting bracket. Then slide the position plate upward to the slot 2 and select the proper location. Then rotate the screw cover 2 to fix the monitor on the bracket. 2.
ELECTRICAL CONNECTION To other DVD/VCD system REMOTE To the +12V power terminal RED Ground wire BLACK DC PLUG S-VIDEO IN (YELLOW) (WHITE) (RED) VIDEO IN(YELLOW) AUDIO L IN(WHITE) AUDIO R IN(RED) 3
LOCATION AND FUNCTION OF KEYS 13 13 12 12 14 17 15 18 16 11 10 3 4 9 8 7 1. (Power Button) 2. Power Indicator Light 3. IR (Remote Sensor) 4. MENU 5.TV/AV/AUTO 6.CHANNEL+ 7.CHANNEL8.VOLUME+ 9.VOLUME- 6 5 2 1 11 10. 6.5 inch color TFT LCD 11. Speakers 12. Volume Knob 13. Jacks for Earphone 14. REMOTE Jack 15.DIVERSITY ANTENNA 16.DC 12V Input Jack 17.S-VIDEO Jack 18.AV IN Jacks FIG. A 6.
LOCATION AND FUNCTION OF KEYS 1. (Power) Press button (1) to turn on/off the unit. 2. POWER INDICATOR LIGHT When the system is on, the indicator light (2) will be illuminated. 3. REMOTE SENSOR For option, the monitor can be supplied with the remote control according to the user's need. Through the remote sensor IR (3), you can use the remote control to execute TV operation conveniently.
LOCATION AND FUNCTION OF KEYS 9. VOLUMEPress the VOLUME- button (9) to decrease the volume level of the speaker. 10. TFT LIQUID CRYSTAL DISPLAY The 7 inch TFT color LCD (10) can show the current state of the unit There also have another LCD for option, see FIG.A the 6.5 inch TFT color LCD 11. SPEAKER There are two speaks (11) on the front of the monitor. The sound can be sent from the speakers if the unit isn't connected with earphone. 12.
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. NO POWER Check if the power button on the front of the monitor is set to on. Check if the wires of DC power plug are properly connected. Check if there is power at the power supply outlet.
BRACKET 3 (BKT3) 8
INSTALLATION HARDWARE (2) (3) (4) (5) (1) (6) (7) (a) (9) (8) (b) (10) (1) ASSY (Rotate combined bracket with Base A..................................................1 (2) Base B................................................................................................................ 1 (3) Plastic tube......................................................................................................... 2 (4) Screw ( 3x10)...................................................................
INSTALLATION 1. Press the switch under the headrest of the car seat and pull out the headrest. Headrest Switch 2. Combine the base B (2) and the base A with steel ripple pipe (1), then place them on the poles of the removed headrest to select proper hole position to install the base. (2) (1) Steel ripple pipe 3.
INSTALLATION 4. Place the Base on the poles of the removed headrest in good position, and then use four screws (3x10 ΓΈ (4) to fix the base A and base B. (4) Screw (1) (2) 5. Install the headrest with the Base to the car seat in proper position, then use the screwdriver to rotate the two screws tightly to fix the base. 6. Use the fix bolt (8) and the fastener (7) to install the tray(9) to the steel ripple pipe.
INSTALL THE TV DISPLAY UNIT OR THE CAMERA 1. INSTALL THE TV MONITOR Insert the position clip screw (5) into the hole on the tray, then insert the circular sheet of the position clip screw (5) to the position plate (referring to the " ADDITIONAL MATERIAL EXPLANATION" below) on the bottom of the TV monitor and rotate the clip screw (6) to the screw of the position clip-screw(5) from underside to fix the TV monitor to the tray. Position plate (5)Position clip-screw (6)Clip screw 2.
ADJUST THE ANGLE OF THE TV UNIT OR THE CAMERA 1. To adjust the angle of the monitor Rotate the clip screw (6) to loosen the TV monitor, then rotate the TV monitor left or right to your need for good viewing angle and then rotate the clip screw tightly to fix the TV monitor. To adjust the angle of the camera Rotate the position clip-screw (5) to loosen the camera, then rotate the camera left or right to your need and then rotate the position clip-screw tightly to fix the camera.
ADDITIONAL MATERIAL EXPLANATION (1) (2) (1) Position plate........................................................................................................1 (2) Screw...................................................................................................................
www.pyleaudio.
