PLVW8M OWNER'S MANUAL TFT MONITOR www.pyleaudio.
INSTALLATION The monitor (Fig.1) can be installed on the bracket (Fig.2). You can mount the unit according to the following steps. Monitor Slot 2 Mounting Bracket Slot 1 Fig.1 Position Plate Screw Cover 1 Rotation Top Screw Cover 2 Base Rotation Base Fig2. 1. Insert the position plate on the bracket into the slot 1 on the mounting bracket. Then slide the position plate upward to the slot 2 and select the proper location. Then rotate the screw cover 2 to fix the monitor on the bracket. 2.
ELECTRICAL CONNECTION To other DVD/VCD system REMOTE RED To the +12V power terminal Ground wire BLACK DC PLUG S-VIDEO IN (YELLOW) (WHITE) (RED) VIDEO IN(YELLOW) AUDIO L IN(WHITE) AUDIO R IN(RED) 3
LOCATION AND FUNCTION OF KEYS 13 13 12 12 14 16 17 15 11 10 3 4 9 8 7 1. (Power Button) 2. Power Indicator Light 3. IR (Remote Sensor) 4. MENU 5. MUTE 6. VOLUME+ 7. VOLUME8. PICTURE+ 9. PICTURE- 6 5 2 1 11 10. 8 inch color TFT LCD 11. Speakers 12. Volume Knob 13. Jacks for Earphone 14. REMOTE Jack 15. DC 12V Input Jack 16. S-VIDEO Jack 17.
LOCATION AND FUNCTION OF KEYS 1. (Power) Press button (1) to turn on/off the unit. 2. POWER INDICATOR LIGHT When the system is on, the indicator light (2) will be illuminated. 3. REMOTE SENSOR For option, the monitor can be supplied with the remote control according to the user's need. Through the remote sensor IR (3), you can use the remote control to execute TV operation conveniently.
LOCATION AND FUNCTION OF KEYS 10. TFT LIQUID CRYSTAL DISPLAY The 8 inch TFT color LCD (10) can show the current state of the unit. 11. SPEAKER There are two speaks (11) on the front of the monitor. The sound can be sent from the speakers if the unit isn't connected with earphone. 12. EARPHONE VOLUME CONTROL KNOB Slide the knob (12) to change the volume of the earphone. 13. JACKS FOR EARPHONE There are two jacks (13) for earphone. You can connect earphone to any one of the jacks to receive sound signal. 14.
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. NO POWER Check if the power button on the front of the monitor is set to on. Check if the wires of DC power plug are properly connected. Check if there is power at the power supply outlet.
BRACKET 3 (BKT3) 8
INSTALLATION HARDWARE (2) (3) (4) (5) (1) (6) (7) (a) (9) (8) (b) (10) (11) (12) (13) (14) (1) ASSY (Rotate combined bracket with Base A..................................................1 (2) Base B................................................................................................................ 1 (3) Plastic tube ( 13mm) ........................................................................................ 2 (4) Screw ( 3x10)...................................................
INSTALLATION 1. Press the switch under the headrest of the car seat and pull out the headrest. Headrest Switch 2. Combine the base B (2) and the base A with steel ripple pipe (1), then place them on the poles of the removed headrest to select proper hole position to install the base. (2) (1) Steel ripple pipe 3.
INSTALLATION 4. Place the Base on the poles of the removed headrest in good position, and then use four screws (3x10 ΓΈ (4) to fix the base A and base B. (4) Screw (1) (2) 5. Install the headrest with the Base to the car seat in proper position, then use the screwdriver to rotate the two screws tightly to fix the base. 6. Use the fix bolt (7) and the fastener (6) to install the tray(9) to the steel ripple pipe.
INSTALL THE TV MONITOR OR THE CAMERA 1. INSTALL THE TV MONITOR Insert the clip screw (5) into the hole on the tray with the washer (a) (8) between the clip screw (5) and the tray. Then aim the clip screw to the hole on the bottom of the TV monitor and rotate the clip screw to fix the TV monitor to the tray. You can also use the fix bolt (7) replacing the clip screw (5) to install the monitor. (8)Washer(a) (5)Clip screw or (7) Fix bolt 2.
ADJUST THE ANGLE OF THE TV UNIT OR THE CAMERA 1. Rotate the clip screw to loosen the TV monitor or the camera, then rotate the TV monitor or the camera left or right to your need for good viewing angle and then rotate the clip screw tightly to fix the TV monitor or the camera. (5)Clip screw or (7) Fix bolt (5)Clip screw 2. The steel ripple pipe can be bent to get the TV monitor or the camera in the proper position that your need.
ADDITIONAL MATERIAL EXPLANATION (1) (2) (1) Position plate........................................................................................................1 (2) Screw...................................................................................................................
www.pyleaudio.
