Owner manual

Thanks again for purchasing your new 409 stainless steel Pypes Performance Exhaust header/cross-member back sys-
tem. Please be sure to conrm all the components in the kit were received in your shipment before beginning installation.
These kits will include (1) X-pipe kit, (2) Mufers (if purchased), (2) tailpipes, (2) collector extensions, (2) mufer hangers,
(2) tailpipe hangers, (8) clamps, and (1) bonus pack. If you purchased a kit including mufers you will see the follow-
ing notation after the system number: (S) Street Pro, (R) Race Pro, and (V) Violator. If you nd any component missing,
please contact our ofce at 800-421-3890 for replacement. Installation of this kit will require some simple hand tools; box
wrenches, deep sockets w/ ratchet, extension, a saws-all and some penetrating lubricant. For a quicker and tighter instal-
lation, air tools are recommended. Fully welding the system is always recommended when possible. Technical assis-
tance is available both online at www.pypesexhaust.com or 800-421-3890. Also our online Installation Gallery is a great
assistant during your installation, www.pypesexhaust.com/pictures.html .
1. Begin by placing the vehicle on a lift or four jack stands at maximum height to aid in an easier installation. To help
ease the installation, pre-t all the components into a complete system on your garage oor, using the diagram provided.
2. Remove the existing exhaust system from the headers or exhaust manifolds back. You can also remove any
hangers mounted to the frame as your new kit includes factory reproduction hangers.
3. Now install your new components. Begin by installing, the new tailpipe hangers. These holes are located approx
12-16” forward from the rear bumper, on the outside of the frame rails. Next, the mufer hangers install just forward of
the rear end housing to the cross-member which is perpendicular to the frame rails. Your new hangers have two rubber
straps with three holes each. They install as follows: the vertical strap gets bolted through the middle hole to the cross-
member parallel to the oor towards the outside of the car. The horizontal strap gets bolted through the top of the cross
member by wrapping the rubber strap into a “C” shape. The bolt will need to go though the top hole in the strap. Next,
install a complete clamp on each hanger.
4. Install the two tailpipes on to the clamps you just installed on the hangers. Snug the nuts to hold the tailpipes in
place. Your new tailpipes will not require trimming unless installing tips.
5. Now, install the mufers. The inlet should be closest to the drive shaft and the outlet should be towards the rock-
ers of the car. The clamp attached to the hanger at the backside of the mufer will be the only connection clamp used.
6. Next, install the x-pipe. This is where trimming of the tubing may be required for the optimum t. Install the rear
legs into the mufers rst. You are aiming to have the center “X” land approx 8-12 inches behind the tail shaft of your
transmission and centered under the driveshaft. Also, the center plate on the “X” has an arrow stamp which must point
forward. Trim the rear legs as needed to put your “X” and mufers in the proper location. Quick tip: If the rear suspension
is unloaded, you can push the center “X” up until it just about touches the drive shaft as it will never hit once t he suspen-
sion is loaded. Slide the front legs into the x-pipe. They should end somewhere close to the humps in your transmission
cross-member. On some applications, the front “X” legs may not be centered in the humps but line up to your headers or
down-pipes. This is ne as the system will not hang too low. Be extra careful when measuring and cutting. A helpful tip:
Line up the front legs under the center “X” to mark your cut lines making sure to line them up with you headers or down
pipes.
7. Continue by connecting the front legs of the x-pipe to the headers (collector reducers) utilizing the two 1ft collec-
tor extension pipes. Trimming the length will be required. Do not connect the x-pipe directly your headers. If down pipes
(see down-pipe instructions) are used, make sure the pipe ends close to the rear side of the transmission cross member.
If they are too long they must be trimmed. Some header applications require custom collectors due to the header not
ending square and parallel to the car. For proper system t, your collectors must run parallel with your rocker panels.
8. Finish the system by making all your nal adjustments to position the x-pipe, mufers and tailpipes. Now tighten
all the clamps (Warning: tightened clamps will leave marks in the tubing, making removal or adjustments extremely dif-
cult) or for the best t weld all the slip joints. The 409 stainless can be welded with your standard mig welder, and is
highly recommended when possible.
Nowit’stimetoreupthatmusclecarandenjoyyournewPypesPerformanceExhaust.
INSTALLATION INSTRUCTIONS