U.S.A.
PRECAUTIONS Thank you for purchasing this HI-FI product. Taking time to read these operating instructions carefully before use will acquaint you fully with all its features and help ensure Do not remove the case and bottom panel Any inspections or adjustments inside the unit optimum performance. In order to simplify the explanation illustrations may may lead to malfunctions and electric shocks. sometimes differ from the originals. Do not touch any of the inside parts.
CONNECTIONS Connection precautions When connecting, either disconnect the power plug PHONO CD AUX VIDEO TUNER TAPE PLAY REC EQ PLAY REC from the power outlet or turn off the unit’s power L using the POWER switch. R Check the left and right channels and connect properly (Left to L and Right to R). L INE Insert the plugs securely. Improper connection can lead PLAY (O UT) ( IN) R EC to the generation of noise.
CONNECTIONS Speaker connection Connect the speaker systems to the SPEAKERS terminals Tuner on the rear panel of the unit with the speaker cords. Connect the TUNER terminals to the OUTPUT terminals When viewed from the front (the listening position), the on the tuner using the pin-plug cord. speaker mounted on the left should be connected to the L terminals, and the speaker mounted on the right should be PHONO CD AUX VIDEO TUNER TAPE PLAY REC connected to the R terminals.
PANEL INFORMATION 1 18 9 2 4 16 15 6 MASTER VOLUME ST EREO HIG H-FIDELITY AM PLIFIE R PA-3 035 POWER BASS TREBLE 0 2 2 4 0 2 4 6 6 2 4 4 8 8 6 6 ON / STANDBY 8 Down VOLUME LEVEL - oo dB -58 dB -48 dB Up -38 dB -28 dB 8 -10 -18 dB 10+ -8 dB -10 10+ BALANCE -0 dB L PHONO MUTE TUNER 17 TAPE VIDEO PRESET EQ AUX VOLUME LEVEL DISPLAY VOL MIC 1 MIC 1 7 8 EXTERNAL PROCESSOR MULTI-FUNCTION REMOTE CONTROLLED SYSTEM PHONES 19 CD R 20 14 13 12 11 10 3
OPERATING PROCEDURES Before starting operation Check that the controls have been set to the following positions before commencing operation Rotate the VOLUME control counterclockwise as far as it will go and set it at the “0” minimum volume position. Set the BALANCE control to its center position. Set the BASS and TREBLE tone controls to the “0” (center) position. After these checks, press the POWER switch to turn on the power.
OPERATION POWER CD 1 2 PRESET EQ 3 4 5 EXTERNAL PROCESSOR 6 7 8 9 10 1 2 3 4 5 6 7 MUTE PHONO AMP DISPLAY VOLUME VIDEO/ AUX 12 13 STOP 14 15 PROGRAM 8 9 TAPE MEM CLEAR MEM 16 17 TUNER/ BAND 18 CD N/M DISPLAY 10 REPEAT 19 20 21 11 1. POWER Power is supplied to the amplifier when pressing this switch once and the power is switched off if pressing once more. 2.
OPERATION 20. REPEAT Press REPEAT button once, the display will show out ERPEAT 1 , then the track which is under playback state or ready state will repeat until you switch off the CD player or press STOP (■). Press REPEAT button once more, REPEAT ALL will shown on the display, all tracks will be repeated until you switch off the CD player or press STOP (■) button. Press this key again will resume to normal playback mode. (P.S: This key only works with our CD of our HI-FI system.) 21.
SPECIFICATIONS Power output………………Rated 50W + 50W Output level (1 KHz) ( 8 ohms, T.H.D. 10% 1 khz) TAPE REC……………….250 mV into 47 koms Reference 30W + 30 W Signal to noise ratio (short-circuit, A-network) (8 ohms, T.H.D.1% 1 khz) PHONO…………………..60dB TUNER, TAPE PLAY…….70dB Load impedance……………8 ohms Total harmonic distortion…less than 0.05% at 1/2 rated Power requirements MS power output. Power voltage……………..230V, 50Hz For U.S.
