Bell Ringer Installation Instructions pyramidtimesystems.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions OVERVIEW Thank you for choosing a TimeTrax Sync™ 5300 Bell Ringer. The TimeTrax Sync™ 5300 directs bells and horns (sold separately) to promote accountability, productivity and punctuality with standardized class changes, shift changes, production schedules, arrival time, breaks and departure time. The 5300 handles single zone configuration and provides 24V DC power to bells and horns up to 1amp maximum total load.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions 41670 CONTENTS Bell Ringer pyramidtimesystems.com Installation Instructions 5300 SINGLE BELL RINGER POWER IN SIGNAL RJ45 BELL IN OUT POWER 24VDC pyramidtimesystems.com TimeTrax Sync™ 5300 Bell Ringer RJ45 Cable pyramidtimesystems.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions 41670 WALL MOUNTING pyramidtimesystems.com 5300 SINGLE BELL RINGER POWER IN SIGNAL RJ45 BELL IN OUT POWER 24VDC 3 1 Select a location for mounting. Power outlet should be within 5 feet of mounting location. 2 Hold the case in desired location and mark holes for drilling. Drill holes for mounting. 3 For sheet rock walls, use plastic anchors. WALL MOUNTING 888.479.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions INSTALLATION 1 The 5300 Bell Ringer requires one of the following Pyramid interface products for operation; 4000, 4000HD, 5000HD, PSDLAUBKK, TTPROXEK, TTELITEEK, 9T1WI, S9DWXSLAUB. Prior to installation, make sure the time is set on the time clock or transmitter from which bell/horn signal will be sent. 2 Plug the end of the power supply into the power port located on the far left side of the bottom of the 5300 case.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions INSTALLATION (Cont.) 4 Insert RJ45 cable into the BCD port located on the bottom of the 5300 case. 5 Insert other end RJ45 cable into BCD port on the side or back of time clock. The top light will turn green, signaling connection (this can take up to 2 minutes). Continue to step 8 on next page. Note: The time clock must be powered and have the time set. If the time is not set, the indicator light will not turn on.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions BELL/HORN CONNECTION 8 Connect 24Volt DC bell or horn to the 5300 bell ringer by pushing the bell wire into the connector located on the far right of the bottom of the 5300. Positive (red) is on the left, and negative (black) is on the right. To remove, gently push the orange clip down to release wires. 8 9 If more than one bell or horn is needed, daisy chain the units in parallel. pyramidtimesystems.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions BELL SCHEDULES 10 If using a TimeTrax™ Elite Time Clock System or a TimeTrax Sync™ RF Wireless Transmitter to send a signal to the 5300, set up bell schedule according to the time clock or transmitter software instructions. Once the schedule has been saved, be sure to upload the schedule.
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions SPECIFICATIONS SPECIFICATIONS Zones Single Signal Devices 41361 6” 24V DC bell, 41392 8” 24V DC bell 41362 24V DC horn Max Load 1 amp Compatible Signal Devices 4000, 4000HD, 4000Pro, 5000, 5000HD Auto Totaling Time Clocks, PSDLAUBKK, TTPROXEK, TTELITEEK Elite Time Clock Systems, 9T1WI, S9DWXSLAUB RF Wireless Transmitters Dimensions (WxHxD) 4.25” X 5.25” X 1.25” Weight .
TIMETRAX™ SYNC 5300 BELL RINGER Installation Instructions WARRANTY 1-YEAR LIMITED WARRANTY Pyramid warranties its Synchronized Clock Systems to the original user against defective material or workmanship for a period of 1 year from date of purchase. The manufacturer’s responsibility under this Warranty is limited to repair or replacement of defective part or parts. Pyramid reserves the right to determine whether parts failed because of defective material, workmanship, or other causes.
THIS PAGE DOES NOT PRINT
CONTACT US: For more information, visit pyramidtimesystems.com or call our technical support team at 888.479.7264 during regular business hours: 8am-5pm EST, Monday-Friday. Copyright © 2017 Pyramid Time Systems, LLC. All rights reserved. I2037 Rev.