Specifications

Home Theater
Section 3
66
Order Online
www.mcminone.com
NET 30
Terms
3
SAM™ Impedance Matching
Speaker Distribution System
The Smart Audio Management (SAM) distribution system distributes
speaker level stereo signal, from one source, to six stereo (12 mono), or 12
stereo (24 mono), listening zones. Power tap resistors are continuously
adjustable from 0.5~4.0ohm, allowing accurate setting of system
impedance. Because resistors are used, much wider frequency response is
possible without high or low frequency roll off, typical of impedance matching
transformers. Input terminals accept a spade lug up to 8 gauge, or 10AWG
wire. Detachable output terminals accept up to 12AWG wire. White powder
coated 16 gauge steel cabinet mounts inside standard 2 x 4 stud walls, and is
marked for proper depth in
1
⁄4" and
1
⁄2" drywall, allowing flush mounting of
front panel. Numerous mounting holes and 25 cable knockouts are located on
all sides, UL/CSA approved strain reliefs are included. Flush mount, vented
front panel attaches via quarter-turn Dzus™ fasteners. The printed circuit
board is easily removable, allowing installation of only the enclosure during
pre–construction. An optional six–zone speaker selector (SM6) is available,
and distribution systems is available with our without the selector pre–installed.
SM6 Enclosure Dimensions Front Panel
Order # Model # Zones Selector Power Capacity (H) x (W) x (D) (H) x (W) (ea.)
50-7000 SAM100 6 stereo/12 mono No 60W/120W RMS/peak 12" x 10" x 3" 14" x 12" $145.00
50-7005 SAM105 6 stereo/12 mono Yes 60W/120W RMS/peak 12" x 10" x 3" 14" x 12" 169.00
50-7010 SAM200 12 stereo/24 mono No 120W/240W RMS/peak 12" x 13" x 3" 14" x 15" 189.00
50-7015 SAM205 12 stereo/24 mono Yes 120W/240W RMS/peak 12" x 13" x 3" 14" x 15" 215.00
Speaker Selector Volume Control
These control boxes can operate multiple speaker pairs of 4, 8 and 16ohm impedance in any combination and can
be used with either one or two stereo amplifiers. This makes it convenient to listen to different program material
in different rooms. 216W Optimatch™ attenuators are employed so that worst case operating conditions will
appear as a 4ohm load to the amp. Made in USA.
Order # Speaker Pairs (1-3) (4-9) (10-up)
50-2390 Six $309.00 $299.00 $294.00
50-2395 Four 224.00 220.42 215.27
Front
Rear
Multi Room Speaker Distribution Strip
Essential for distributed residential sound
installations, this terminal strip provides a
convenient method of connecting numerous pairs
of speakers to a single pair of binding posts. Input
terminals are heavy duty, gold plated brass, five–way
binding posts, which will accept single or paired
banana plugs or bare wire up to 8AWG. Each output
connection features detachable screw terminal strips
which accept up to 14AWG wire. Internal PC board
circuit is reinforced with internal point–to–point
14AWG wiring, for improved current capacity.
Compact size allows easy location behind equipment.
Screw holes allow easy wall mounting and rubber
feet are included for shelf top use. Note: Terminal
strip is straight parallel connection and provides
no impedance protection. It is intended for use
with impedance matching volume controls, such
as #50-7870, #50-7880 or #50-6377A. Specifications:
•Power capacity: 200W RMS per channel
•Dimensions: 2" (H) x 2.25" (W) x 10.5" (L),
including binding posts.
Order # (1–3) (4–up)
50-2204 $29.95 $27.77
Multi Room Speaker Distribution Strip
Designed for use in multi room sound distribution
installations where individual speaker selection is not
required. Impedance protection circuit allows up to
eight sets of 8ohm speakers to be connected to a
stereo amplifier, and appear as a 4ohm load.
Completely independent left and right circuits allow
compatibility with all amplifier types. Attached
mounting plate allows installation into standard 19"
racks, or between studs spaced on 16" centers.
Features: •Color coded push terminals accept up to
8AWG wire •Switchable impedance protection
•Non-inductive resistors for full frequency response
•Rugged aluminum housing with black finish
Specifications: •Power capacity: 120W program per
channel •Frequency response: 20Hz~20KHz
•Dimensions: 3.5" (H) x 19.0" (W) x 2.25" (D)
Order # (1-3) (4-up)
50-2202 $84.99 $77.40
Two-Way Speaker
Switch Box
Tabletop control box
allows selection of A/B
speaker pairs. Internal 220ohm
resistors ensure that amplifier always sees a load,
even with both switches off. With both speaker
switches in “on” position, speaker pairs are
connected in series, allowing use of 4ohm or 8ohm
speaker systems, without damage to amplifier. 200W
maximum power capacity. All connections are push
type. Metal case has non-skid rubber feet and stays
securely in place. Dimensions: 6.9" (W) x 2.2" (H) x
3.9" (D). Sloped front, black color.
Order # (1-5) (6-9) (10-up)
50-6185 $17.59 $16.17 $13.56
Top
Back
Table-Top Speaker
Volume Control
Table-top control
center provides
external volume adjustment for a single pair of
speakers. 12 position rotary control utilizes multi
tapped transformers for efficient power transfer,
with no heat build-up. Front panel
1
⁄4" headphone
jack mutes speakers for private listening and is
controlled by the volume control. Rear speaker in/out
connections are heavy duty push terminal strips and
accept up to 14AWG wire. Heavy metal case has
non-skid rubber feet and stays securely in place.
Power capacity: 100W RMS per channel.
Dimensions: 1
3
⁄4" (H) x 7" (W) x 3
5
⁄8" (D). Silver color.
Order # (1-4) (5-9) (10-up)
50-6216 $31.50 $29.36 $25.70
Table-Top Speaker Selector/Volume Control
Versatile control
center combines
switching
capability for
two speaker
pairs, with a volume adjustment for pair #2. 12
position rotary control utilizes multi tapped
transformers for efficient power transfer, with no
heat build-up. Front panel
1
⁄4" headphone jack mutes
both speaker pairs for private listening and is
controlled by the volume control. Rear speaker in/out
connections are heavy duty push terminal strips and
accept up to 14AWG wire. Heavy metal case has
non-skid rubber feet and stays securely in place.
Power capacity: 100W RMS per channel.
Dimensions: 1
3
⁄4" (H) x 9
5
⁄8" (W) x 4" (D). Silver color.
Note: When two pairs of speakers are selected, they
are in parallel, so impedance must be considered.
When both speakers are in off position, pair #1 will
remain on, preventing damage to amplifiers with
outputs sensitive to open loads.
Order # (1-4) (5-9) (10-up)
50-6211 $38.95 $36.00 $31.88
8" Acoustic Baffle
•Protects PA
speakers from
dust and water
contamination
•Improves sound
quality •Pliable to fit most any
installation •Packaged in pairs
Order # (pr.)
60-290 $10.06
Audio
LeveliZer
™
Line Level
Stabilizer
Maintains a
constant average
output loudness,
regardless of the audio
source type or loudness.
Perfect for louder than
program commercials on radio and TV, and volume
variations between different broadcasting stations,
records and CDs (perfect for multi-disc players).
Connect to the tape loop of any amplifier or receiver,
or between the pre-amp and power amplifier, or
between audio outputs of TV or VCR and amplifier
inputs. Because this device monitors average input
level, normal program dynamics experienced in high
action video scenes are maintained. Dimensions:
2
1
⁄8" (H) x 7
1
⁄8" (W) x 3
3
⁄4" (D) exluding control knob.
Black in color.
Order # (ea.)
50-6155 $230.00
Front
Back
C51 pg 066 7/28/06 9:54 AM Page 66