Specifications

72
Order Online
www.mcmelectronics.com
NET 30
Terms
3
Home Theater
section
3
Speaker Selectors
Table top selectors are ideal for
distributed audio systems where multiple speaker
pairs are to be connected to a single amplifier.
Available in four or six zone configurations, with
or without volume controls for each zone. Features:
•Switchable resistor type impedance protection,
allowing full frequency response •Detachable
snap-lock connectors •Custom room labels •Non-skid
rubber feet •12-step rotary volume controls on each
zone (applicable models) •100W per channel power
capacity Specifications: •Frequency response:
20Hz~20KHz •Minimum impedance
to amplifier: 8ohm
Order # Mfr. # Zones Volume Controls (ea.)
50-8470 S4 four no $84.95
50-8471 S6 six no 115.00
50-8475 S4VC four yes 239.00
50-8476 S6VC six yes 285.00
#50-8470
#50-8475
Wall Mount
IR Receivers
Plasma proof IR receiver rejects
interference common of flat panel
displays, CFL lighting and indirect
sunlight. Single gang decora style
mounts in standard electrical boxes
or low voltage brackets and may be
combined with other low voltage
devices behind a multiple gang
decora plate. Features: •Extended
receiving range •Red status LED •Blue talkback LED
•Snap-and-lock connector •Includes matching decora
faceplate •Requires two pairs of Cat 5 or
higher wire •Depth behind faceplate: 2
3
⁄4"
•Mfr. #IR-WMR
Order # Color (ea.)
50-8591 White $65.00
50-8592 Bone 65.00
50-8595 Almond 65.00
Flush Mount IR Receiver
Plasma proof IR receiver rejects
interference common of flat panel
displays, CFL lighting and
indirect sunlight. Compact
flush mount design is perfect
for installation into wall
plates, entertainment system panels or any other
flat surface. All JobSite in-wall speaker systems
include a knock-out for installation of this receiver.
Features: •Receiving range: 18'~30' depending
remote •Works up to 30° off axis •Includes black and
white bezels •Includes attached 10' connecting cable
•Requires two pairs of Cat 5 or higher wire •Front
bezel diameter:
3
⁄4" •Required mounting hole:
1
⁄2"
•Mounting depth: 2
5
⁄16" •Mfr. #IR-FMR
Order # (ea.)
50-8600 $89.95
Compact Surface
Mount IR Receiver
Plasma proof IR receiver rejects
interference common of flat panel
displays, CFL lighting and indirect
sunlight. Simple self-adhesive
surface mounting allows the unit to
be located on virtually any smooth clean surface.
Features: •Red status LED •Blue talkback LED
•Receiving range: 18'~30' depending remote
•Works up to 30° off axis •Black color •Includes
attached 10' connecting cable •Requires two pairs of
Cat5 or higher wire •Dimensions:
1
⁄2" (H) x
11
⁄16" (W) x
2
1
⁄16" (D) •Mfr. #IR-SMR
Order # (ea.)
50-8605 $82.95
Complete IR
Repeater Kit
Complete
plasma proof
IR repeater
kit includes all
necessary components for
control of up to five devices from a remote
location. Kit includes: •One IR-CB2 connecting
block with power supply •Five IR-E1 emitters
•One IR-SMR IR receiver •Mfr. #IR-KIT
Order # (kit)
50-8610 $189.00
Single Zone
IR Connecting
Block
Intended as
the hub of the
complete JobSite Plasma proof IR repeater system,
this connecting block provides point of connection
for emitters, receivers and power supply.
Features: •Single zone control •Single IR receiver
input •Four IR emitter outputs •Snap lock receiver
inputs •3.5mm emitter outputs •Includes UL listed
12VDC power supply •Dimensions: 1
1
⁄4" (H) x
4
3
⁄4" (W) x 2" (D) •Mfr. #IR-CB1
Order # (ea.)
50-8615 $49.95
Two Zone
IR Connecting
Block
Intended as the
hub of the complete JobSite Plasma proof IR
repeater system, this connecting block provides point
of connection for emitters, receivers and power supply.
Features: •Two zone control •Two IR receiver inputs
•Five IR emitter outputs •Selectable high/low emitter
output for use with high output, single and dual
emitters •Snap lock receiver inputs •3.5mm emitter
outputs •Includes UL listed 12VDC power supply
•Dimensions: 1
1
⁄4" (H) x 5
11
⁄16" (W) x 2" (D)
•Mfr. #IR-CB2
Order # (ea.)
50-8620 $64.95
Four Zone
IR Connecting
Block
Intended as
the hub of the
complete JobSite Plasma
proof IR repeater system, this
connecting block provides point of
connection for emitters, receivers and power supply.
Features: •Four zone control •Four IR receiver
inputs •Eight IR emitter outputs •Selectable high/low
emitter output for use with high output, single and
dual emitters •12VDC output for sensing status or
discrete IR commands •Contact closure triggered by
sensing status or discrete IR commands •Snap lock
receiver inputs •3.5mm emitter outputs •Includes UL
listed 12VDC power supply •Dimensions: 1
1
⁄4" (H) x
7
1
⁄16" (W) x 3" (D) •Mfr. #IR-CB4
Order # (ea.)
50-8625 $89.95
Six Zone IR
Connecting
Block
Expander
Increases a
single input on the JobSite connecting block from
one to six. Greatly reduces clutter in areas where
numerous IR sensors are placed some distance from
the connecting block. Instead of home running all
sensors to the block, they can be hubbed at this
expander, with a single run to the block. Features:
•Snap lock connectors •Six IR receiver inputs
•Talkback LED indicates system status •Dimensions:
1
1
⁄4" (H) x 7
1
⁄16" (W) x 1
1
⁄4" (D) •Mfr. #IR-CBE6
Order # (ea.)
50-8630 $49.95
IR Emitter
Designed to provide IR signal to
source equipment from remote
location, this emitter attaches
directly to the IR window on
system equipment. Specially designed pass-through
housing does not block IR window, allowing local
control as normal. Features: •10' attached cable
terminated with 3.5mm two conductor plug •Cable
length may be increased up to 40' with 18AWG cable
•Cable length may be increased up to 200' with
16AWG cable •Emits IR signal up to 48" line of
sight •Peel-and-stick self adhesive mounting •Ultra
compact size:
3
⁄16" (H) x
5
⁄16" (W) x
1
⁄2" (D) •Mfr. #IR-E1
Order # (ea.)
50-8635 $8.99
Dual IR Emitter
Designed to provide IR
signal to source equipment
from remote location, this
emitter attaches directly to
the IR window on system
equipment. Specially designed pass-through housing
does not block IR window, allowing local control as
normal. Dual emitters on a single plug increase the
total number of emitters that may be connected to a
single control block. Features: •10' attached cable
on each emitter, terminated with a single 3.5mm two
conductor plug •Emits IR signal up to 48" line of
sight •Peel-and-stick self adhesive mounting •Ultra
compact size (each emitter):
3
⁄16" (H) x
5
⁄16" (W) x
1
⁄2" (D)
•Mfr. #IR-E2
Order # (ea.)
50-8636 $16.25
High Output IR Emitter
Designed to provide IR signal to
source equipment from remote
location, high output emitter
mounts inside equipment racks and floods the
entire cavity with the IR pulse, thus controlling
all equipment in the rack. This serves as a suitable
alternative to locating individual emitters on every
piece of equipment. Features: •10' attached cable
terminated with a 3.5mm two conductor plug •Emits
IR signal up to 18'~30' line of sight •Peel-and-stick
self adhesive mounting •Dimensions:
3
⁄8" (H) x
1" (W) x 2
1
⁄4" (D) •Mfr. #IR-E1HO
Order # (ea.)
50-8640 $22.50
C52_pg_072 8/7/07 2:40 PM Page 72