0 Simplify SANbox2-8c Fibre Channel Switch Installation Guide Firmware Version 4.
0 SANbox2-8c Fibre Channel Switch Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.7.1 1.7.2 1.7.4 1.7.5 1.7.6 1.8 1.9 1.10 1.11 1.12 1.13 1.13.1 1.13.2 1.13.3 1.14 1.14.1 1.14.2 1.14.3 Intended Audience ............................................................................................. 1-1 Related Materials ............................................................................................... 1-2 New in this Release.................................................................................
SANbox2-8c Fibre Channel Switch Installation Guide 0 2.1.2.1 2.1.2.2 2.1.2.3 2.1.2.4 2.2 2.2.1 2.2.1.1 2.2.1.2 2.2.2 2.2.3 2.3 2.4 2.5 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 Over Temperature LED (Amber)....................................................... 2-4 Fan Fail LED (Amber)....................................................................... 2-4 Heartbeat LED (Amber) .................................................................... 2-4 Input Power LED (Green) ...............................
0 SANbox2-8c Fibre Channel Switch Installation Guide 3.6 Fabric Management ......................................................................................... 3-12 Section 4 Installation 4.1 4.1.1 4.1.2 4.1.3 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.4.1 4.2.4.2 4.2.5 4.2.5.1 4.2.5.2 4.2.6 4.2.7 4.2.8 4.2.9 4.3 4.3.1 4.3.2 4.4 Site Requirements.............................................................................................. 4-1 Fabric Management Workstation...................................
SANbox2-8c Fibre Channel Switch Installation Guide 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 0 Maintenance – Exit .................................................................................. 5-12 Maintenance – Image Unpack................................................................. 5-12 Maintenance – Reset Network Config ..................................................... 5-13 Maintenance – Reset User Accounts to Default......................................
0 SANbox2-8c Fibre Channel Switch Installation Guide Quit Command ........................................................................................B-29 Reset Command......................................................................................B-30 Set Command..........................................................................................B-35 Set Config Command ..............................................................................B-37 Set Log Command........................
0 SANbox2-8c Fibre Channel Switch Installation Guide Tables Table 2-1 3-1 3-2 4-1 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 B-9 B-10 B-11 B-12 B-13 B-14 B-15 B-16 B-17 Page Serial Port Pin Identification ........................................................................................... 2-9 Zoning Database Limits ................................................................................................. 3-2 Port-to-Port Latency .........................................................................
Section 1 Introduction This manual describes the features and installation of the SANbox2-8c Fibre Channel switch, firmware version 4.2. This manual is organized as follows: Section 1 describes the intended audience, related materials, safety notices, communications statements, laser safety information, electrostatic discharge sensitivity precautions, accessible parts, general program license, and technical support. Section 2 is an overview of the switch.
0 1 – Introduction Related Materials 1.2 Related Materials The following manuals and materials are referenced in the text and/or provide additional information. SANbox2-8c/16 Switch Management User’s Guide, publication number 59022-10. QLogic Switch Interoperability Guide v3.0. This PDF document can be downloaded at http://www.qlogic.com/interopguide/info.asp#inter. Fibre Channel-Arbitrated Loop (FC-AL-2) Rev. 6.8. Fibre Channel-10-bit Interface Rev. 2.3.
0 1 – Introduction Safety Notices 1.4 Safety Notices A Warning notice indicates the presence of a hazard that has the potential of causing personal injury. 4-3, 4-17 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment. 4-4, 5-14 1.5 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin, die möglicherweise Verletzungen zur Folge hat.
0 1 – Introduction Communications Statements 1.7 Communications Statements The following statements apply to this product. The statements for other products intended for use with this product appear in their accompanying manuals. 1.7.1 Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
0 1 – Introduction Communications Statements 1.7.3 Avis de conformité aux normes du ministère des Communications du Canada Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits radioélectriques por les appareils numériques, telles que prescrites par le Réglement sur le brouillage radioélectrique établi par le ministère des Communications du Canada.
1 – Introduction Communications Statements 0 1.7.5 VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 1.7.6 BSMI Class A Statement Warning: This is a Class A product.
0 1 – Introduction Laser Safety Information 1.8 Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors. The U.S. Department of Health and Human Services (DHHS) does not consider Class 1 lasers to be hazardous. The International Electrotechnical Commission (IEC) 825 Laser Safety Standard requires labeling in English, German, Finnish, and French stating that the product uses Class 1 lasers.
1 – Introduction General Public License 0 1.13 General Public License QLogic® Fibre Channel switches are powered by the Linux® operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License.
0 1 – Introduction General Public License We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.
1 – Introduction General Public License 0 modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a. You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b.
0 1 – Introduction General Public License b. Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c.
1 – Introduction General Public License 0 rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 8. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
0 1 – Introduction General Public License License, you may choose any version ever published by the Free Software Foundation. 12. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
0 1 – Introduction General Public License one line to give the program's name and an idea of what it does. Copyright (C) yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
0 1 – Introduction Technical Support 1.14 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates. 1.14.
1 – Introduction Technical Support 0 Notes 1-16 59042-07 A
Section 2 General Description This section describes the features and capabilities of the SANbox2-8c Fibre Channel switch. The following topics are described: Chassis controls and LEDs Fibre channel ports Ethernet port Serial port Power supply and fan Switch management Fabrics are managed with the SANsurfer Switch Manager™ switch management application (version 4.02) and the Command Line Interface (CLI).
0 2 – General Description Chassis Controls and LEDs 2.1 Chassis Controls and LEDs The Maintenance button shown in Figure 2-2 is the only chassis control and is used to reset a switch or to recover a disabled switch. The chassis LEDs provide information about the switch’s operational status. These LEDS include the Over Temperature LED, Fan Fail LED, Heartbeat LED, and the Input Power LED.
0 2 – General Description Chassis Controls and LEDs 2.1.1 Maintenance Button The Maintenance button is a dual-function momentary switch on the front panel. Its purpose is to reset the switch or to place the switch in maintenance mode. Maintenance mode sets the IP address to 10.0.0.1 and provides access to the switch for maintenance purposes when flash memory or the resident configuration file is corrupted. Refer to “Recovering a Switch” on page 5-11 for more information about using maintenance mode. 2.1.
0 2 – General Description Chassis Controls and LEDs 2.1.2 Chassis LEDs The chassis LEDs shown in Figure 2-3 provide status information about switch operation. Refer to “Port LEDs” on page 2-6 for information about port LEDs. Over Temperature LED (Amber) Fan Fail LED (Amber) Input Power LED (Green) Heartbeat LED (Amber) Figure 2-3. Chassis LEDs 2.1.2.1 Over Temperature LED (Amber) The Over Temperature LED provides status information about the air temperature inside the switch.
0 2 – General Description Fibre Channel Ports 2.1.2.4 Input Power LED (Green) The Input Power LED indicates the voltage status at the switch logic circuitry. During normal operation, this LED illuminates to indicate that the switch logic circuitry is receiving the proper DC voltages. 2.2 Fibre Channel Ports The SANbox2-8c switch has 8 Fibre Channel ports numbered 0–7 as shown in Figure 2-4. Each of these ports is served by a Small Form-Factor Pluggable (SFP) optical transceiver.
0 2 – General Description Fibre Channel Ports 2.2.1 Port LEDs Each Fibre Channel port has its own Logged-In LED and Activity LED as shown in Figure 2-5. Logged-In LED (Green) Activity LED (Green) Figure 2-5. Port LEDs 2.2.1.1 Port Logged-In LED The Logged-in LED indicates the logged-in or initialization status of the connected devices. After successful completion of the POST, the switch extinguishes all Logged-In LEDs.
0 2 – General Description Fibre Channel Ports 2.2.2 Small Form-Factor Pluggable (SFP) Transceivers An SFP transceiver, like the one shown in Figure 2-6, converts electrical signals to and from optical laser signals to transmit and receive. SFP transceivers plug into the ports; duplex fiber optic cables plug into the transceivers which then connect to the devices. A port is capable of transmitting at 1-Gbps or 2-Gbps; however, the transceiver must be capable of 2-Gbps for the port to deliver at that rate.
0 2 – General Description Ethernet Port E_Ports enable you to expand the fabric by connecting SANbox2-8c switches with other switches. SANbox2-8c switches self-discover all inter-switch connections. Refer to “Multiple Chassis Fabrics” on page 3-6 for more information about multiple chassis fabrics. Refer to the SANbox2-8c/16 Switch Management User’s Guide for more information about defining port types. 2.
0 2 – General Description Serial Port 2.4 Serial Port The SANbox2-8c switch is equipped with an RS-232 serial port for maintenance purposes. The serial port location is shown in Figure 2-8. You can manage the switch through the serial port using the CLI. 5 1 6 9 Serial Port Figure 2-8. Serial Port and Pin Identification The serial port connector requires a null-modem F/F DB9 cable. The pins on the switch RS-232 connector are shown in Figure 2-8 and identified in Table 2-1.
0 2 – General Description Power Supply and Fan 2.5 Power Supply and Fan The power supply converts standard 110 or 230 VAC to DC voltages for the various switch circuits. An internal fan provides cooling. Air flow can be front-to-back or back-to-front depending on the switch model. To energize the switch, plug the power cord into the switch AC receptacle and into a 110 or 230 VAC power source. Note: The power supply and fan are not field replaceable units. 2.
0 2 – General Description Switch Management 2.6.2 SANsurfer Switch Manager Web Applet To make switch management less dependent on a particular workstation, each switch contains a SANsurfer Switch Manager web applet. One instance of the web applet can be run at a time by opening the switch IP address with an internet browser. The switch comes from the factory with the web applet enabled, but you can disable it using the EmbeddedGUIEnabled parameter of the Set Setup System command.
2 – General Description Switch Management 0 2.6.6 File Transfer Protocol FTP provides the command line interface for exchanging files between the switch and the management workstation. These files include firmware image files, configuration files, and log files. “Backing up and Restoring Switch Configurations” on page B-4 provides an example of using FTP to transfer configuration files.
Section 3 Planning Consider the following when planning a fabric: Devices Device Access Performance Multiple Chassis Fabrics Fabric Security Fabric Management 3.1 Devices When planning a fabric, consider the number of devices and the anticipated demand. This will determine the number of ports that are needed and the number of switches. Consider how many and what types of switches are needed. The switch uses SFP transceivers, but the device host bus adapters you are using may not.
0 3 – Planning Device Access 3.2 Device Access Consider device access needs within the fabric. Access is controlled by the use of zones and zone sets. Some zoning strategies include the following: Group devices by operating system. Separate devices that have no need to communicate with other devices in the fabric or have classified data. Separate devices into department, administrative, or other functional group. Reserve a path and its bandwidth from one port to another.
0 3 – Planning Device Access 3.2.1 Soft Zones Soft zoning divides the fabric for purposes of controlling device discovery. Devices in the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. The following rules apply to soft zones: Soft zones that include members from multiple switches need not include the ports of the inter-switch links.
0 3 – Planning Performance 3.3 Performance The SANbox2-8c switch supports class 2 and class 3 Fibre Channel service with a maximum frame size of 2148 bytes at transmission rates of 1-Gbps or 2-Gbps. A switch port adapts its transmission speed to match that of the device to which it is connected prior to login when the connected device powers up. Related performance characteristics include the following: Distance Bandwidth Latency 3.3.
0 3 – Planning Performance 3.3.2 Bandwidth Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate. A port can transmit or receive at nominal rates of 1-Gbps or 2-Gbps depending on the device to which it is connected. This corresponds to actual bandwidth values of 106 MB and 212 MB respectively. Two 1-Gbps source ports can transmit to the same 2-Gbps destination port. Similarly, one 2-Gbps source port can feed two 1-Gbps destination ports.
0 3 – Planning Multiple Chassis Fabrics 3.4 Multiple Chassis Fabrics By connecting switches together you can expand the number of available ports for devices. Each switch in the fabric is identified by a unique domain ID, and the fabric can automatically resolve domain ID conflicts. Because the Fibre Channel ports are self-configuring, you can connect the SANbox2-8c switch with other switches in a wide variety of topologies. 3.4.
0 3 – Planning Multiple Chassis Fabrics 3.4.2 Domain ID, Principal Priority, and Domain ID Lock The following switch configuration settings affect multiple chassis fabrics: Domain ID Principal priority Domain ID lock The domain ID is a unique number from 1–239 that identifies each switch in a fabric. The principal priority is a number (1–255) that determines the principal switch which manages domain ID assignments for the fabric.
0 3 – Planning Multiple Chassis Fabrics 3.4.3 Common Topologies The SANbox2-8c switch supports the following topologies: Cascade Topology Mesh Topology Multistage Topology 3.4.3.1 Cascade Topology A cascade topology describes a fabric in which the switches are connected in series. If you connect the last switch back to the first switch, you create a cascade-with-a-loop topology as shown in Figure 3-1.
0 3 – Planning Multiple Chassis Fabrics 3.4.3.2 Mesh Topology A mesh topology describes a fabric in which each chassis has at least one port directly connected to each other chassis in the fabric. The example mesh fabric shown in Figure 3-2 has the following characteristics: Each link contributes up to 200 MB/s of bandwidth between switches, 400 MB/s in full duplex. Because of multiple parallel paths, there is less competition for this bandwidth than with a cascade or a Multistage topology.
0 3 – Planning Multiple Chassis Fabrics 3.4.3.3 Multistage Topology A Multistage® topology describes a fabric in which two or more edge switches connect to one or more core switches. The Multistage fabric shown in Figure 3-3 has the following characteristics: Each link contributes up to 200 MB/s of bandwidth between chassis. Competition for this bandwidth is less than that of a cascade topology, but greater than that of the mesh topology.
0 3 – Planning Fabric Security 3.5 Fabric Security Fabric security consists of the following: User account security Fabric services 3.5.1 User Account Security User account security consists of the administration of account names, passwords, expiration date, and authority level. If an account has Admin authority, all management tasks can be performed by that account in both SANsurfer Switch Manager™ and the Telnet command line interface. Otherwise, only monitoring tasks are available.
0 3 – Planning Fabric Management 3.6 Fabric Management The SANsurfer Switch Manager application and CLI execute on a management workstation that provides for the configuration, control, and maintenance of multiple fabrics. Supported platforms include Windows, Solaris, and Linux. The application can be installed and executed on the workstation, or you can run the SANsurfer Switch Manager web applet that is resident on the switch.
Section 4 Installation This section describes how to install and configure the SANbox2-8c switch. It also describes how to load new firmware and how to recover a disabled switch. 4.1 Site Requirements Consider the following items when installing a SANbox2-8c switch: Fabric Management Workstation Switch Power Requirements Environmental Conditions 4.1.
0 4 – Installation Installing a Switch 4.1.3 Environmental Conditions Consider the factors that affect the climate in your facility such as equipment heat dissipation and ventilation. The switch requires the following operating conditions: Operating temperature range: 5 – 50°C (41 – 122°F) Relative humidity: 15 – 80%, non-condensing 4.2 Installing a Switch Unpack the switch and accessories.
0 4 – Installation Installing a Switch Installing a SANbox2-8c switch involves the following steps: 1. Mount the switch. 2. Install SFP transceivers. 3. Connect the management workstation to the switch. 4. Configure the management workstation. 5. Install the management application. 6. Start the management application. 7. Connect the switch to the AC power source. 8. Configure the switch. 9. Cable devices to the switch. 4.2.
0 4 – Installation Installing a Switch CAUTION! If the switch is mounted in a closed or multi-unit rack assembly, make sure that the operating temperature inside the rack enclosure does not exceed the maximum rated ambient temperature. Refer to “Environmental” on page A-4. The switch must rest on rails or a shelf in the rack or cabinet. Allow 16 cm (6.5 in) minimum clearance at the front and rear of the rack for service access and ventilation. Do not restrict chassis air flow. Allow 16 cm (6.
0 4 – Installation Installing a Switch 4.2.3 Connect the Workstation to the Switch You can manage the switch using SANsurfer Switch Manager or the command line interface. SANsurfer Switch Manager requires an Ethernet connection to the switch. The command line interface can use an Ethernet connection or a serial connection.
0 4 – Installation Installing a Switch 4.2.4 Configure the Workstation If you plan to use the command line interface to configure and manage the switch, you must configure the workstation. This involves setting the workstation IP address for Ethernet connections, or configuring the workstation serial port. If you plan to use SANsurfer Switch Manager to manage the switch, the Configuration Wizard manages the workstation IP address for you – proceed to “Install the Management Application” on page 4-8. 4.2.
0 4 – Installation Installing a Switch c. Enter the following COM Port settings in the COM Properties window and choose the OK button. Bits per second: 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None For Linux: a. Set up minicom to use the serial port. Create or modify the /etc/minirc.dfl file with the following content: pr pu pu pu portdev/ttyS0 minit mreset mhangup pr portdev/ttyS0 specifies port 0 on the workstation.
0 4 – Installation Installing a Switch 4.2.5 Install the Management Application You can manage the switch using SANsurfer Switch Manager as a standalone application or as a part of SANsurfer Management Suite™. SANsurfer Management Suite is QLogic’s integrated fabric management application, managing both HBAs and switches.
0 4 – Installation Installing a Switch For a Linux workstation: 1. If a file browser does not open, double-click the CD-ROM icon to open the browser. Double click the Switch_Manager folder, then double click the Linux folder. If there is no CD-ROM icon, do the following: a. Open an xterm or other terminal window. b. Mount the CD-ROM. From a shell prompt, enter the following command: mount /mnt/cdrom c. Change directory to location of the install program: cd /mnt/cdrom/Switch_Manager/Linux 2.
0 4 – Installation Installing a Switch 4.2.5.2 SANsurfer Management Suite The following instructions describe how to install SANsurfer Management Suite and upgrade SANsurfer Switch Manager. You can install SANsurfer Management Suite (SMS) on a Windows, Linux, or Solaris workstation. Choose the instructions for your workstation: SMS Installation for Windows SMS Installation for Linux SMS Installation for Solaris 4.2.5.2.
0 4 – Installation Installing a Switch 7. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file from the SANsurfer Management Suite installation directory. You can also start SANsurfer Management Suite by clicking the SANsurfer icon (if installed) on the desktop or from the Start menu. In SMS, Click the Switch tab in the left pane. From the Help menu, select About ... and make note of the version number. Close SANsurfer Management Suite. 8.
0 4 – Installation Installing a Switch 4.2.5.2.2 SMS Installation for Linux Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the management workstation CD-ROM drive. 1. If a file browser dialog opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Management Suite start page. If a file browser does not open, double-click the CD-ROM icon to open the browser.
0 4 – Installation Installing a Switch 10. 11. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and Manuals. a. Select your switch model from the pull-down menu. Locate the description for SANsurfer Switch Manager for Linux under "Management Software". b. If the release version number (4.02.xx) is greater than what is currently installed on your workstation, down load the new version and proceed to step 11.
0 4 – Installation Installing a Switch 4.2.5.2.3 SMS Installation for Solaris To install the SANsurfer Switch Manager application on Solaris from the SANsurfer Management Suite CD-ROM, do the following: 1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If the SANsurfer Management Suite start page does not open in your default browser, do the following: a. Right-click the Workspace Menu. b. Select File, then select File Manager. c.
0 4 – Installation Installing a Switch 10. 11. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and Manuals. a. Select your switch model from the pull-down menu. Locate the description for SANsurfer Switch Manager for Linux under "Management Software". b. If the release version number (4.02.xx) is greater than what is currently installed on your workstation, down load the new version.
0 4 – Installation Installing a Switch 4.2.6 Start SANsurfer Switch Manager You can start SANsurfer Switch Manager as a standalone application or from SANsurfer Management Suite. Note: After the switch is operational, you can also open the SANsurfer Switch Manager web applet, by entering the switch IP address in an internet browser. If your workstation does not have the Java 2 Run Time Environment program, you will be prompted to download it.
0 4 – Installation Installing a Switch 3. In the Initial Start dialog, click the Open Configuration Wizard button. When you power up the switch, the Configuration Wizard will recognize the switch and lead you through the configuration process. 4.2.7 Connect the Switch to AC Power WARNING!! This product is supplied with a 3-wire power cable and plug for the user’s safety. Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock.
0 4 – Installation Installing a Switch WARNUNG!! Dieses Produkt wird mit einem 3-adrigen Netzkabel mit Stecker geliefert. Dieses Kabel erfüllt die Sicherheitsanforderungen und sollte an einer vorschriftsmäßigen Schukosteckdose angeschlossen werden, um die Gefahr eines elektrischen Schlages zu vermeiden.Elektrosteckdosen, die nicht richtig verdrahtet sind, können gefährliche Hochspannung an den Metallteilen des switch-Gehäuses verursachen.
0 4 – Installation Installing a Switch The Heartbeat LED indicates the results of the POST. The POST tests the condition of firmware, memories, data-paths, and switch logic circuitry. If the Heartbeat LED blinks steadily about once per second, the POST was successful, and you can continue with the installation process. Any other blink pattern indicates that an error has occurred. Refer to “Heartbeat LED Blink Patterns” on page 5-2 for more information about error blink patterns.
0 4 – Installation Installing a Switch To configure the switch using the command line interface, do the following: 1. Open a command window according to the type of workstation and connection: Ethernet (all platforms): Open a Telnet session with the default switch IP address and log in to the switch with default account name and password (admin/password). telnet 10.0.0.1 SANbox Login: admin Password: ******* Serial – Windows: Open the HyperTerminal application on a Windows platform. a.
0 4 – Installation Install Firmware 4.2.9 Cable Devices to the Switch Connect cables to the SFP transceivers and their corresponding devices, and then energize the devices. Device host bus adapters can have SFP (or SFF) transceivers or GigaBit Interface Converters (GBIC). LC-type duplex fiber optic cable connectors are designed for SFP transceivers, while SC-type connectors are designed for GBICs. Duplex cable connectors are keyed to ensure proper orientation.
0 4 – Installation Install Firmware 4.3.1 Using SANsurfer Switch Manager to Install Firmware To install firmware using SANsurfer Switch Manager, do the following: 1. Select a switch in the topology display and double-click to open the Faceplate display. Open the Switch menu and select Load Firmware. 2. In the Firmware Upload window, click the Select button to browse and select the firmware file to be uploaded. 3. Click the Start button to begin the loading process. 4.3.
0 4 – Installation Powering Down a Switch 2. Enter your account name on the remote host and the IP address of the remote host. When prompted for the source file name, enter the path for the firmware image file. When prompted to install the new firmware, enter Yes to continue or No to cancel. This is the last opportunity to cancel. User Account : johndoe IP Address : 10.20.20.200 Source Filename : 4.0.2.00.04_x86 About to install image. Do you want to continue? [y/n] y Connected to 10.20.20.200 (10.20.20.
4 – Installation Powering Down a Switch 0 Notes 4-24 59042-07 A
Section 5 Diagnostics/Troubleshooting Diagnostic information about the switch is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the SANsurfer Switch Manager and CLI event logs and error displays. This section describes two types of diagnostics: Power On Self Test (POST) and chassis. POST diagnostics describe the Heartbeat LED and the port Logged-In LED indications.
0 5 – Diagnostics/Troubleshooting POST Diagnostics 5.1.1 Heartbeat LED Blink Patterns The Heartbeat LED indicates the operational status of the switch. When the POST completes with no errors, the Heartbeat LED blinks at steady rate of once per second. When the switch is in maintenance mode, the Heartbeat LED illuminates continuously. Refer to “Recovering a Switch” on page 5-11 for more information about maintenance mode. All other blink patterns indicate critical errors.
0 5 – Diagnostics/Troubleshooting POST Diagnostics 5.1.1.3 Configuration File System Error Blink Pattern A configuration file system error blink pattern is 4 blinks followed by a two second pause. The 4-blink error pattern indicates that a configuration file system error has occurred, and that the configuration file must be recreated. Refer to “Recovering a Switch” on page 5-11 for more information.
5 – Diagnostics/Troubleshooting POST Diagnostics 5. 0 The following menu is displayed. Enter "6" (Remake Filesystem) and press the Enter key to recreate the configuration file. 0) Exit 1) Image Unpack 2) Reset Network Config 3) Reset User Accounts to Default 4) Copy Log Files 5) Remove Switch Config 6) Remake Filesystem 7) Reset Switch Option: 6 6. When the recreate process is complete, select option 7 to reset the switch and exit maintenance mode. 7.
0 5 – Diagnostics/Troubleshooting POST Diagnostics g. Open an admin session to acquire the necessary authority. SANbox2 $>admin start h. Restore the configuration file. When the restore is complete, the switch will reset. SANbox2 (admin) $>config restore 5.1.2 Logged-In LED Indications Port diagnostics are indicated by the Logged-In LED for each port as shown in Figure 5-1. Logged-In LED Figure 5-1.
5 – Diagnostics/Troubleshooting POST Diagnostics 0 5.1.2.1 E_Port Isolation A Logged-In LED error indication is often the result of E_Port isolation. An isolated E_Port is indicated by a red link in the SANsurfer Switch Manager topology display.
0 5 – Diagnostics/Troubleshooting POST Diagnostics 4. Display the active zone set on each switch using the Zoning Active command or the Active Zoneset tab of the SANsurfer Switch Manager topology display. Compare the zone membership between the two active zone sets. Are they the same? Yes - Contact your authorized maintenance provider. No - Deactivate one of the active zone sets or edit the conflicting zones so that their membership is the same. Reset the port.
5 – Diagnostics/Troubleshooting POST Diagnostics 0 Review the event browser to determine if excessive port errors are responsible for disabling the port. Look for a message that mentions one of the monitored error types indicating that the port has been disabled, then do the following: 1. 2. 3. 4. 5-8 Examine the alarm configuration for the associated error using the Show Config Threshold command or the SANsurfer Switch Manager application. Refer to the “Show Config Command” on page B-73.
0 5 – Diagnostics/Troubleshooting Chassis Diagnostics 5.2 Chassis Diagnostics Chassis diagnostics are indicated by the chassis LEDs as shown in Figure 5-2. Over Temperature LED (Amber) Fan Fail LED (Amber) Input Power LED (Green) Heartbeat LED (Amber) Figure 5-2. Chassis LEDs The following conditions are described: Over Temperature LED is illuminated Input Power LED is extinguished Fan Fail LED is illuminated 5.2.
5 – Diagnostics/Troubleshooting Chassis Diagnostics 0 5.2.2 Input Power LED Is Extinguished The Input Power LED illuminates to indicate that the switch logic circuitry is receiving proper voltages. If the Input Power LED is extinguished, do the following: 1. 2. Inspect the power cords and connectors. Is the cord unplugged? Is the cord or connector damaged? Yes - Make necessary corrections or repairs. If the condition remains, continue. No - Continue. Inspect the AC power source.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5.3 Recovering a Switch A switch can become inoperable or unmanageable for the following reasons: Firmware becomes corrupt IP address is lost Switch configuration becomes corrupt Forgotten password In these specific cases, you can recover the switch using maintenance mode. Maintenance mode temporarily returns the switch IP address to 10.0.0.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5. The maintenance menu displays several recovery options. To select a switch recovery option, press the corresponding number (displayed in option: field) on the keyboard and press the Enter key. 0) Exit 1) Image Unpack 2) Reset Network Config 3) Reset User Accounts to Default 4) Copy Log Files 5) Remove Switch Config 6) Remake Filesystem 7) Reset Switch Option: These options and their use are described in the following subsections. 5.3.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5. Select option 1 from the maintenance menu. When prompted for a file name prompt, enter the firmware image file name. Image filename: filename Unpacking ’filename’, please wait... Unpackage successful. 6. Select option 7 to reset the switch and exit maintenance mode. 5.3.3 Maintenance – Reset Network Config This option resets the network properties to the factory default values and saves them on the switch.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5.3.7 Maintenance – Remake Filesystem In the event of sudden loss of power, it is possible that the switch configuration may become corrupt. The file system on which the configuration is stored must be re-created. This option resets the switch to the factory default values including user accounts and zoning. Refer to Table B-3 though Table B-8 for the factory default values.
Appendix A Specifications This appendix contains the specifications for the SANbox2-8c Fibre Channel switch. Refer to Section 2 General Description for the location of all connections, switches, controls, and components. A.1 Fabric Specifications Fibre Channel Protocols ................. FC-PH Rev. 4.3 FC-PH-2 FC-PH-3 FC-AL Rev 4.5 FC-AL-2 Rev 7.0 FC-FLA FC-GS-3 FC-FG FC-Tape FC-VI FC-SW-2 Fibre Channel Element MIB RFC 2837 Fibre Alliance MIB Version 4.0 Fibre Channel Classes of Service ..
0 A – Specifications Maintainability Buffer Credits.................................. 12 buffer credits per port Media Type ..................................... Small Form Pluggable (SFP) optical transceivers. Hot swappable. 3.3 Volts. Fabric Port Speed ........................... 1.0625 or 2.125-Gbps Maximum Frame Size..................... 2148 bytes (2112 byte payload) System Processor........................... 266 MHz Geode® processor Fabric Latency (best case) ............. <0.4 µsec.
0 A – Specifications Fabric Management A.3 Fabric Management Management Methods .................... SANsurfer Switch Manager Graphical User Interface Application Programming Interface Command Line Interface GS-3 Management Server SNMP FTP Maintenance Connection ................ RS-232 connector; null modem F/F DB9 cable Ethernet Connection ....................... RJ-45 connector; 10/100 BASE-T cable Switch Agent...................................
0 A – Specifications Environmental A.6 Environmental Temperature Operating .................................. 5 to 50°C (41 to 122°F) Non-operating ........................... -40 to 65°C (-40 to 149°F) Humidity Operating .................................. 15% to 80%, non-condensing Non-operating ........................... 25% to 90%, non-condensing Altitude Operating .................................. 0 to 3048m (0 to 10,000 feet) Non-operating ...........................
Appendix B Command Line Interface The command line interface (CLI) enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection. This section describes the following: Logging On to a Switch User Accounts Working with Switch Configurations Commands B.
B – Command Line Interface Working with Switch Configurations 0 This user account provides full access to the switch and its configuration. After planning your fabric management needs and creating your own user accounts, consider changing the password for this account. Refer to “Commands” on page B-6 for information about authority levels. Refer to the “User Command” on page B-89 for information about creating user accounts.
0 B – Command Line Interface Working with Switch Configurations The Show Switch command displays the name of the active configuration. A configuration name can have up to 31 characters excluding the pound symbol (#), semicolon (;), and comma (,). By editing the latest configuration and saving the results under a new name, you can create a history of configuration changes.
B – Command Line Interface Working with Switch Configurations 0 B.3.2 Backing up and Restoring Switch Configurations Backing up and restoring a configuration is useful to protect your work or for use as a template in configuring other switches. The Config Backup command creates a file on the switch, named configdata. This file can be used to restore a switch configuration only from the command line interface; it cannot be used to restore a switch using SANsurfer Switch Manager.
0 B – Command Line Interface Working with Switch Configurations The restore operation begins with FTP to upload the configuration file from the workstation to the switch, then finishes with a Telnet session and the Config Restore command. To upload the configuration file, config_switch_169_10112003 in this case, open and FTP session with account name images and password images.
0 B – Command Line Interface Commands B.4 Commands The command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The Command is followed by one or more keywords. Consider the following rules and conventions: Commands and keywords are case insensitive. Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value]. Underlined portions of the keyword in the command format indicate the abbreviated form that can be used.
0 B – Command Line Interface Commands The command set performs monitoring and configuration tasks. Commands related to monitoring tasks are available to all account names. Commands related to configuration tasks are available only within an admin session. An account must have Admin authority to enter the Admin Start command, which opens an admin session. Refer to the “Admin Command” on page B-8. The commands and their page numbers are listed in Table B-2. Table B-2.
0 B – Command Line Interface Admin Command Admin Command Opens and closes an Admin session. The Admin session provides commands that change the fabric and switch configurations. Only one Admin session can be open on the switch at any time. An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command. Refer to the “Set Setup Command” on page B-53.
0 B – Command Line Interface Alias Command Alias Command Creates a named set of ports/devices. Aliases make it easier to assign a set of ports/devices to many zones. An alias can not have a zone or another alias as a member.
0 B – Command Line Interface Alias Command members [alias] Displays all members of the alias given by [alias]. This keyword does not require an admin session. remove [alias] [member_list] Removes the ports/devices given by [member_list] from the alias given by [alias]. Use a to delimit ports/devices in [member_list]. A port/device in [member_list] can have any of the following formats: Domain ID and port number pair (Domain ID, Port Number). Domain IDs can be 1–-239; port numbers can be 0–-255.
0 B – Command Line Interface Config Command Config Command Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, refer to the “Set Config Command” on page B-37.
B – Command Line Interface Config Command 0 restore Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, then enter the Config Restore command. After the restore is complete, the switch automatically resets. Refer to “Backing up and Restoring Switch Configurations” on page B-4.
0 B – Command Line Interface Config Command The following is an example of how to create a backup file (configdata) and download the file to the workstation.
B – Command Line Interface Create Support Command 0 Create Support Command Assembles all log files and switch memory data into a core dump file (dump_support.tgz zip) and prompts you to send it to a remote host. This file is useful to technical support personnel for troubleshooting switch problems. Use this command when directed by your authorized maintenance provider.
0 B – Command Line Interface Create Support Command 221-You have transferred 43430 bytes in 1 files. 221-Total traffic for this session was 43888 bytes in 1 transfers. 221 Thank you for using the FTP service on localhost.localdomain.
B – Command Line Interface Date Command 0 Date Command This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Network Time Protocol (NTP) must be disabled to set the time with the Date command. Refer to the “Set Setup Command” on page B-53, System keyword, for information about NTP. Authority Admin session except to display the date.
0 B – Command Line Interface Firmware Install Command Firmware Install Command Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch (without a power-on self test) to activate the firmware. If possible, a non-disruptive activation is performed.
B – Command Line Interface Hardreset Command 0 Hardreset Command Resets the switch and performs a power-on self test. This reset disrupts traffic, activates the pending firmware, and clears the alarm log. To save the alarm log before resetting, refer to the “Set Log Command” on page B-48. Authority Admin session Syntax Notes hardreset To reset the switch without a power-on self test, refer to the “Reset Command” on page B-30.
0 B – Command Line Interface Help Command Help Command Displays a brief description of the specified command, its keywords, and usage. Authority None Syntax Keywords help [command] [keyword] [command] Displays a summary of the command given by [command] and its keywords. If you omit [command], the system displays all available commands. [keyword] Displays a summary of the keyword given by [keyword] belonging to the command given by [command].
0 B – Command Line Interface History Command History Command Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority None Syntax Notes history Examples Use the History command to provide context for the ! command: Enter ![command_string] to re-execute the most recent command that matches [command_string].
0 B – Command Line Interface Hotreset Command Hotreset Command Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This command terminates all management sessions, saves all configuration information, and clears the event log. After the pending firmware is activated, the configuration is recovered. This process takes less than 80 seconds. To save the event log to a file before resetting, refer to the “Set Log Command” on page B-48.
0 B – Command Line Interface Image Command Image Command Manages and installs switch firmware. Authority Admin session Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] install list unpack [file] Keywords cleanup Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.
0 B – Command Line Interface Image Command 2. Move to the folder or directory on the workstation that contains the new firmware image file. 3. Establish communications with the switch using the File Transfer Protocol (FTP). Enter one of the following on the command line: >ftp xxx.xxx.xxx.xxx or >ftp switchname where xxx.xxx.xxx.xxx is the switch IP address, and switchname is the switch name associated with the IP address. 4.
0 B – Command Line Interface Image Command 12. Wait for the unpack to complete. image unpack command result: Passed 13. A message will prompt you to reset the switch to activate the firmware. Resetting the switch is disruptive. Use the Hotreset command to attempt a non-disruptive activation. SANbox2 (admin) $>hotreset Examples The following is an example of the Image Install command: SANbox2 (admin) #> image install Warning: Installing new firmware requires a switch reset.
0 B – Command Line Interface Lip Command Lip Command Reinitializes the specified loop port. Authority Admin session Syntax Keywords lip [port_number] Examples The following is an example of the Lip command: [port_number] The number of the port to be reinitialized. Ports are numbered beginning with 0.
0 B – Command Line Interface Passwd Command Passwd Command Changes a user account’s password. Authority Admin account name and an admin session to change another account’s password; You can change you own password without an Admin session. Syntax Keywords passwd [account_name] Examples The following is an example of the Passwd command: [account_name] The user account name. To change the password for an account name other than your own, you must open an admin session with the account name Admin.
0 B – Command Line Interface Ping Command Ping Command Initiates an attempt to communicate with another switch over an Ethernet network and reports the result. Authority None Syntax ping ip_address Keywords ip_address The IP address of the switch to query. Examples The following is an example of a successful Ping command: SANbox2 #> ping 10.20.11.57 Ping command issued. Waiting for response... SANbox2 #> Response successfully received from 10.20.11.57.
0 B – Command Line Interface Ps Command Ps Command Displays current system process information. Authority None Syntax Examples ps The following is an example of the Ps command: SANbox2 #> ps PID B-28 PPID %CPU TIME ELAPSED COMMAND 338 327 0.0 00:00:00 3-01:18:35 cns 339 327 0.0 00:00:01 3-01:18:35 ens 340 327 0.0 00:00:21 3-01:18:35 dlog 341 327 0.1 00:05:35 3-01:18:35 ds 342 327 0.2 00:11:29 3-01:18:35 mgmtApp 343 327 0.0 00:00:04 3-01:18:35 fc2 344 327 0.
0 B – Command Line Interface Quit Command Quit Command Closes the Telnet session. Authority None Syntax Notes quit, exit, or logout 59042-07 A You can also enter Control-D to close the Telnet session.
0 B – Command Line Interface Reset Command Reset Command Resets the switch configuration parameters. If you omit the keyword, the default is Reset Switch. Authority Admin session Syntax reset config [config_name] factory port [port_number] snmp switch (default) system zoning Keywords config [config_name] Resets the configuration given by [config_name] to the factory default values for switch, port, port threshold alarm, and zoning configuration.
0 B – Command Line Interface Reset Command Clears the event log. To save the event log before resetting, refer to the “Set Log Command” on page B-48. To reset the switch with a power-on self test, refer to the “Hardreset Command” on page B-18. To reset the switch without disrupting traffic, refer to the “Hotreset Command” on page B-21. system Resets the system configuration settings to the factory default values. Refer to Table B-8 for system configuration default values.
0 B – Command Line Interface Reset Command Table B-4. Port Configuration Defaults Parameter Default Admin State Online Link Speed Auto Port Type GL Symbolic Name Port n, where n is the port number ALFairness False DeviceScanEnabled True ForceOfflineRSCN False ARB_FF False InteropCredit 0 ExtCredit 0 FANEnable True AutoPerfTuning True LCFEnable False MFSEnable True VIEnable False MSEnable True NoClose False IOStreamGuard Auto PDISCPingEnable True Table B-5.
0 B – Command Line Interface Reset Command Table B-5.
0 B – Command Line Interface Reset Command Table B-7. SNMP Configuration Defaults Parameter Default Trap [1-5] Port 162 Trap [1-5] Severity Warning Trap [1-5] Version 2 Trap [1-5] Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.14 AuthFailureTrap False ProxyEnabled True Table B-8. System Configuration Defaults Parameter B-34 Default Ethernet Network Discovery Static Ethernet Network IP Address 10.0.0.1 Ethernet Network IP Mask 255.0.0.0 Ethernet Gateway Address 10.0.0.
0 B – Command Line Interface Set Command Set Command Sets a variety of switch parameters. Authority Admin session for all keywords except Alarm, Beacon, and Pagebreak which are available without an Admin session. Syntax set alarm [option] beacon [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state] Keywords alarm [option] Controls the display of alarms in the session output stream or clears the alarm log.
B – Command Line Interface Set Command 0 on Limits the display of information to 20 lines at a time. The page break functions affects the following commands: Alias (List, Members), Show (Alarm, Log), Zone (List, Members), Zoneset (List, Zones), Zoning (Active, List). off Allows continuous display of information without a break. port [option] Sets port state and speed for the specified port. The previous Set Config Port settings are restored after a switch reset or a reactivation of a switch configuration.
0 B – Command Line Interface Set Config Command Set Config Command Sets switch, port, port threshold alarm, and zoning configuration parameters. The changes you make with this command are not retained when you reset or power cycle the switch unless you save them using the Config Save command. Refer to the “Config Command” on page B-11.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter B-38 Description SymbolicPortName Descriptive name for the port. The name can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is Port n where n is the port number. ALFairness Arbitration loop fairness. Enables (True) or disables (False) the switch’s priority to arbitrate on the loop. The default is False.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter 59042-07 A Description AutoPerfTuning Automatic performance tuning for FL_Ports only. The default is True. If AutoPerfTuning is enabled (True) and the port is an FL_Port, MFSEnable is automatically enabled. LCFEnable and VIEnable are overridden to False. If AutoPerfTuning is disabled (False), MFSEnable, LCFEnable, and VIEnable retain their original values.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter Description IOStreamGuard I/O Stream Guard. Enables or disables the suppression of RSCN messages. IOStreamGuard can have the following values: Enable – Suppresses the reception of RSCN messages from other ports for which IOStreamGuard is enabled. Disable – Allows free transmission and reception of RSCN messages.
0 B – Command Line Interface Set Config Command Table B-10. Set Config Switch Parameters (Continued) Parameter 59042-07 A Description FDMIEnabled Fabric Device Monitoring Interface. Enables (True) or disables (False) the monitoring of target and initiator device information. FDMIEntries The number of device entries to maintain in the FDMI database. Enter a number from 0–1000. The default is 1000. DefaultDomainID Default domain ID. The default is 1.
0 B – Command Line Interface Set Config Command Table B-10. Set Config Switch Parameters (Continued) Parameter B-42 Description InteropMode Propagates just the active zone set throughout the fabric (True, compliant) or the entire zoning database (False, non-compliant). The default is True. LegacyAddressFormat Available only when the InteropMode parameter is False, this parameter enables (True) or disables (False) the use of legacy address formatting for interoperating with non-FC-SW-2 switches.
0 B – Command Line Interface Set Config Command threshold Initiates a configuration session by which to generate and log alarms for selected events. The system displays each event, its triggers, and sampling window one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. These parameters must be saved in a configuration and activated before they will take effect.
0 B – Command Line Interface Set Config Command zoning Initiates an editing session in which to change switch zoning attributes. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-12.
0 B – Command Line Interface Set Config Command ARB_FF (True / False) [False ] InteropCredit (decimal value, 0-255) [0 ] ExtCredit (dec value, increments of 11, non-loop only) [0 ] FANEnable (True / False) [True ] AutoPerfTuning (True / False) [False ] LCFEnable (True / False) [False ] MFSEnable (True / False) [False ] VIEnable (True / False) [False ] MSEnable (True / False) [True NoClose (True / False) [False ] ] IOStreamGuard (Enable / Disable / Auto) [Disable] PDISCPin
0 B – Command Line Interface Set Config Command The following is an example of the Set Config Threshold command: SANbox2 #> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config threshold A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Config Command Finished configuring attributes. This configuration must be saved (see config save command) and activated (see config activate command) before it can take effect. To discard this configuration use the config cancel command. The following is an example of the Set Config Zoning command. SANbox2 #> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config zoning A list of attributes with formatting and current values will follow.
B – Command Line Interface Set Log Command 0 Set Log Command Specifies the events to record in the event log and display on the screen. You determine what events to record in the switch event log using the Component, Level, and Port keywords. You determine what events are automatically displayed on the screen using the Display keyword. Alarms are always displayed on the screen.
0 B – Command Line Interface Set Log Command None Monitor none of the component events. Other Monitors other miscellaneous events. Port Monitors all port events. SNMP Monitors all SNMP events. Switch Monitors switch management events. Zoning Monitors zoning conflict events. display [filter] Specifies the log events to automatically display on the screen according to the event severity levels given by [filter]. [filter] can be one of the following values: Critical Critical severity level events.
B – Command Line Interface Set Log Command 0 Info Monitors informative, warning, and critical events. The informative level describes routine events associated with a normal fabric. This is the default severity level. None Monitors none of the severity levels. port [port_list] Specifies one or more ports to monitor for events. Choose one of the following values: [port_list] Specifies port or ports to monitor. Use a to delimit values in the list. Ports are numbered beginning with 0.
0 B – Command Line Interface Set Port Command Set Port Command Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin session except for the Clear keyword. Syntax set port [port_number] bypass [alpa] clear enable speed [transmission_speed] state [state] Keywords [port_number] Specifies the port. Ports are numbered beginning with 0.
B – Command Line Interface Set Port Command 0 Down Disables the port by removing power from the port lasers.
0 B – Command Line Interface Set Setup Command Set Setup Command Changes SNMP and system configuration settings. The switch maintains one SNMP configuration and one system configuration. Authority Admin session Syntax set setup snmp system Keywords snmp Prompts you in a line-by-line fashion to change SNMP configuration settings. Table B-13 describes the SNMP fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-13.
0 B – Command Line Interface Set Setup Command Table B-13. SNMP Configuration Settings (Continued) Entry Description ReadCommunity Read community password that authorizes an SNMP agent to read information from the switch. This is a write-only field. The value on the switch and the SNMP management server must be the same. The read community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is “public”.
0 B – Command Line Interface Set Setup Command Table B-14. System Configuration Settings (Continued) Entry 59042-07 A Description Eth0NetworkMask Ethernet subnet mask address. Eth0GatewayAddress Ethernet IP address gateway. AdminTimeout Amount of time in minutes the switch waits before terminating an idle Admin session. Zero (0) disables the time out threshold. The default is 30, the maximum is 1440.
0 B – Command Line Interface Set Setup Command Examples The following is an example of the Set Setup SNMP command: SANbox2 #> admin start SANbox2 (admin) #> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Setup Command TrapCommunity (string, max=32 chars) [public ] AuthFailureTrap (True / False) [False ] ProxyEnabled (True / False) [True ] The following is an example of the Set Setup System command: SANbox2 (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
B – Command Line Interface Show Command 0 Show Command Displays fabric, switch, and port operational information.
0 B – Command Line Interface Show Command chassis Displays chassis component status and temperature. config [option] Displays switch, port, and zoning configuration attributes. Refer to the “Show Config Command” on page B-73. domains Displays list of each domain and its worldwide name in the fabric. donor Displays list of current donor configuration for all ports. fabric Displays list of each domain, symbolic name, worldwide name, node IP address, and port IP address.
0 B – Command Line Interface Show Command ns [option] Displays name server information for the specified [option]. If you omit [option], name server information for the local domain ID is displayed. [option] can have the following values: all Displays name server information for all switches and ports. [domain_id] Displays name server information for the switch given by [domain_id]. [domain_id] is a switch domain ID. [port_id] Displays name server information for the port given by [port_id].
0 B – Command Line Interface Show Command Table B-15. Show Port Parameters (Continued) Entry 59042-07 A Description EpConnects Number of times an E_Port connected through ISL negotiation. FBusy Number of times the switch sent a F_BSY because Class 2 frame could not be delivered within ED_TOV time. Number of class 2 and class 3 fabric busy (F_BSY) frames generated by this port in response to incoming frames.
0 B – Command Line Interface Show Command Table B-15. Show Port Parameters (Continued) Entry Description PrimSeqErrors Primitive sequence errors detected. RxLinkResets Number of link reset primitives received from an attached device. RxOfflineSeq Number of offline sequences received. An OLS is issued for link initialization, a Receive & Recognize Not_Operational (NOS) state, or to enter the offline state. TotalErrors Total number of errors detected.
0 B – Command Line Interface Show Command support Executes a series of commands that display a complete description of the switch, its configuration, and operation. The display can be captured from the screen and used for diagnosing problems. This keyword is intended for use at the request of your authorized maintenance provider.
0 B – Command Line Interface Show Command Table B-16. Switch Operational Parameters (Continued) Parameter Description LogLevel Event severity level used to record events in the event log MaxPorts Number of ports available on the switch NumberOfResets Number of times the switch has been reset over its service life ReasonForLastReset Action that caused the last reset ActiveImageVersion - build date Active firmware image version and build date.
0 B – Command Line Interface Show Command version Displays an introductory set of information about operational attributes of the switch. This keyword is equivalent to the About keyword.
0 B – Command Line Interface Show Command The following is an example of the Show FDMI command: SANbox2 #> show fdmi HBA ID PortID Manufacturer Model Ports -------- ------ --------------- ------- ----- 21:01:00:e0:8b:27:aa:bc 610000 QLogic Corporation QLA2342 2 21:00:00:00:ca:25:9b:96 180100 QLogic Corporation QL2330 2 The following is an example of the Show FDMI WWN command: SANbox2 #> show fdmi 21:00:00:e0:8b:09:3b:17 FDMI Information ---------------Manufacturer QLogic Corporation S
0 B – Command Line Interface Show Command The following is an example of the Show NS (local domain) command: SANbox2 #> show ns Seq Domain Port Port No ID Type COS PortWWN NodeWWN ------ ---- --- ------- ------- ID --- -----1 19 (0x13) 1301e1 NL 3 21:00:00:20:37:73:13:69 20:00:00:20:37:73:13:69 2 19 (0x13) 1301e2 NL 3 21:00:00:20:37:73:12:9b 20:00:00:20:37:73:12:9b 3 19 (0x13) 1301e4 NL 3 21:00:00:20:37:73:05:26 20:00:00:20:37:73:05:26 4 19 (0x13) 130d00 N 3 21:01:00:e0:8b:27:a7:b
0 B – Command Line Interface Show Command The following is an example of the Show Interface command: SANbox2 #> show interface eth0 Link encap:Ethernet HWaddr 00:C0:DD:00:BD:ED inet addr:10.20.68.107 Bcast:10.20.68.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Mask:255.255.255.0 Metric:1 RX packets:4712 errors:0 dropped:0 overruns:0 frame:0 TX packets:3000 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:415313 (405.5 Kb) TX bytes:716751 (699.
0 B – Command Line Interface Show Command The following is an example of the Show Port command: SANbox2 #> show port 1 Port Number: 1 ------------ 59042-07 A AdminState Online OperationalState Online AsicNumber 0 PerfTuningMode Normal AsicPort 1 PortID 0e0800 ConfigType GL PortWWN 20:08:00:c0:dd:03:d5:94 DiagStatus Passed RunningType E EpConnState Connected MediaPartNumber PL-XPL-VC-SG3-22 EpIsoReason NotApplicable MediaRevision 1 IOStreamGuard Disabled MediaType 200-M5-SN-
0 B – Command Line Interface Show Command The following is an example of the Show Switch command: SANbox2 #> show switch Switch Information -----------------SymbolicName sw .108 SwitchWWN 100000c0dd00bc56 SwitchType SANbox2-8c BootVersion Vx.x.x.x-0 (day month date time year) CreditPool 0 DomainID 19 (0x13) FirstPortAddress 130000 FlashSize - MBytes 128 LogLevel Critical MaxPorts 8 NumberOfResets 15 ReasonForLastReset PowerUp ActiveImageVersion - build date Vx.x.x.
0 B – Command Line Interface Show Command The following is an example of the Show Topology command for port 1: SANbox2 #> show topology 1 Local Link Information ---------------------PortNumber 1 PortID 650100 PortWWN 20:01:00:c0:dd:00:91:11 PortType F Remote Link Information ----------------------Device 0 NodeWWN 50:80:02:00:00:06:d5:38 PortType NL Description (NULL) IPAddress 0.0.0.0 Device 1 NodeWWN 20:00:00:20:37:2b:08:c9 PortType NL Description (NULL) IPAddress 0.0.0.
0 B – Command Line Interface Show Command The following is an example of the Show Version command: SANbox2 #> show version ***************************************************** * * * Command Line Interface SHell (CLISH) * * * ***************************************************** B-72 SystemDescription SANbox2-8c FC Switch Eth0NetworkAddress 10.20.11.
0 B – Command Line Interface Show Config Command Show Config Command Displays switch, port, alarm threshold, and zoning for the current configuration. Authority None Syntax show config port [port_number] switch threshold zoning Keywords port [port_number] Displays configuration parameters for the port number given by [port_number]. Ports are numbered beginning with 0. If [port_number] is omitted, all ports are specified. switch Displays configuration parameters for the switch.
0 B – Command Line Interface Show Config Command The following is an example of the Show Config Switch command: SANbox2 #> show config switch Configuration Name: default ------------------Switch Configuration Information -------------------------------AdminState Online BroadcastEnabled False InbandEnabled True FDMIEnabled False FDMIEntries 10 DomainID 19 (0x13) DomainIDLock True SymbolicName sw108 R_A_TOV 10000 E_D_TOV 2000 PrincipalPriority 254 ConfigDescription Default Config Con
0 B – Command Line Interface Show Config Command RisingTrigger 2 FallingTrigger 0 SampleWindow 10 LoginMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LogoutMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LOSMonitoringEnabled True RisingTrigger 100 FallingTrigger 5 SampleWindow 10 The following is an example of the Show Config Zoning command: SANbox2 #> show config zoning Configuration Name: default ------------------- Zoning
B – Command Line Interface Show Log Command 0 Show Log Command Displays the contents of the log or the parameters used to create and display entries in the log. The log contains a maximum of 1200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest.
0 B – Command Line Interface Show Log Command Zoning Monitors zoning conflict events. display [filter] Displays log events on the screen according to the component or severity level filter given by [filter]. [filter] can be one of the following: Info Displays all informative events. Warning Displays all warning events. Critical Displays all critical events. Eport Displays all events related to E_Ports. Mgmtserver Displays all events related to the management server.
0 B – Command Line Interface Show Log Command Examples The following is an example of the Show Log Component command: SANbox2 #> show log component Current settings for log -----------------------FilterComponent NameServer MgmtServer Zoning Switch Blade Port Eport Snmp The following is an example of the Show Log Level command: SANbox2 #> show log level Current settings for log -----------------------FilterLevel Info DisplayLevel Critical The following is an example of the Show Log Options command:
0 B – Command Line Interface Show Perf Command Show Perf Command Displays port performance in frames/second and bytes/second. If you omit the keyword, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames/second and bytes per second. Authority None Syntax show perf byte inbyte outbyte frame inframe outframe errors Keywords byte Displays continuous performance data in total bytes/second transmitted and received for all ports.
0 B – Command Line Interface Show Perf Command Examples The following is an example of the Show Perf command: SANbox2 #> show perf Port Bytes/s Number Bytes/s (in) Bytes/s Frames/s Frames/s Frames/s (out) (total) (in) (out) (total) ------ ------- ------- ------- -------- -------- -------- 0 7K 136M 136M 245 68K 68K 1 58K 0 58K 1K 0 1K 2 0 0 0 0 0 0 3 0 0 0 0 0 0 4 0 0 0 0 0 0 5 0 0 0 0 0 0 6 0 7K 7K 0 245 245 7 136M 58K 136M 68K 1K
0 B – Command Line Interface Show Setup Command Show Setup Command Displays the current SNMP and system settings. Authority None Syntax show setup mfg snmp system Keywords mfg Displays manufacturing information about the switch. snmp Displays the current SNMP settings. system Displays the current system settings.
0 B – Command Line Interface Show Setup Command The following is an example of the Show Setup Snmp command: SANbox2 #> show setup snmp SNMP Information ---------------- B-82 SNMPEnabled True Contact Location N_107 System Test Lab Description SANbox2-8c FC Switch Trap1Address 10.0.0.254 Trap1Port 162 Trap1Severity warning Trap1Version 2 Trap1Enabled False Trap2Address 0.0.0.
0 B – Command Line Interface Show Setup Command The following is an example of the Show Setup System command: SANbox2 #> show setup system System Information ------------------ 59042-07 A Eth0NetworkDiscovery Static Eth0NetworkAddress 10.20.11.32 Eth0NetworkMask 255.255.252.0 Eth0GatewayAddress 10.20.8.254 AdminTimeout 30 InactivityTimeout 0 LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10.0.0.254 NTPClientEnabled True NTPServerAddress 51.68.85.
B – Command Line Interface Shutdown Command 0 Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command. Authority Admin session Syntax Notes shutdown Always use this command to perform an orderly shut down before removing power from the switch. When the shutdown is complete, the Heartbeat LED is extinguished.
0 B – Command Line Interface Test Command Test Command Tests ports using internal (SerDes level), external (transceiver), and online loopback tests. Internal and external tests require that the port be placed in diagnostic mode. Refer to the “Set Command” on page B-35 for information about changing the port administrative state. While the test is running, the remaining ports on the switch remain fully operational.
0 B – Command Line Interface Test Command 3. Choose the type of port loopback test to run: To run an internal loopback test, enter the following: test port x internal To run an external loopback test, enter the following command. A loopback plug must be installed for this test to pass. test port x external 4. A series of test parameters are displayed on the screen. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key.
0 B – Command Line Interface Test Command 3. A series of test parameters are displayed on the screen. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize (256 byte maximum in some cases) parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload.
0 B – Command Line Interface Uptime Command Uptime Command Displays the elapsed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activation does not reset the elapsed up time reported by this command.
0 B – Command Line Interface User Command User Command Administers and displays user accounts. Authority Admin account name and an Admin session. The Accounts and List keywords are available to all account names without an Admin session. Syntax user accounts add delete [account_name] edit list Keywords accounts Displays all user accounts that exist on the switch. This keyword is available to all account names without an Admin session. add Add a user account to the switch.
0 B – Command Line Interface User Command Examples The following is an example of the User Accounts command: SANbox2 (admin) #> user accounts Current list of user accounts ----------------------------images (admin authority = False, never expires) admin (admin authority = True , never expires) chuckca (admin authority = False, expires in < 50 days) gregj (admin authority = True , expires in < 100 days) fred (admin authority = True , never expires) The following is an example of the User Add co
0 B – Command Line Interface User Command The following is an example of the User Delete command: SANbox2 (admin) #> user del user3 The user account will be deleted. Please confirm (y/n): [n] y The following is an example of the User List command: SANbox2 (admin) #> user list 59042-07 A User Ethernet Addr-Port Logged in Since ---- ------------------ --------------- admin@OB-session1 10.20.68.108-1031 day month date time year admin@OB-session2 10.20.68.
0 B – Command Line Interface Whoami Command Whoami Command Displays the account name, session number, and switch domain ID for the Telnet session.
0 B – Command Line Interface Zone Command Zone Command Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit session. Refer to the “Zoning Command” on page B-99 for information about starting a Zoning Edit session. The List, Members, and Zonesets keywords are available without an Admin session.
0 B – Command Line Interface Zone Command list Displays a list of all zones and the zone sets of which they are components. This keyword does not require an Admin session. members [zone] Displays all members of the zone given by [zone]. This keyword does not require an Admin session. remove [zone] [member_list] Removes the ports/devices given by [member_list] from the zone given by [zone]. Use a to delimit aliases and ports/devices in [member_list].
0 Examples B – Command Line Interface Zone Command The following is an example of the Zone List command: SANbox2 #> zone list Zone ZoneSet ------------------wwn_b0241f zone_set_1 wwn_23bd31 zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402f zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command: SANbox2 #> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f -----
B – Command Line Interface Zone Command 0 The following is an example of the Zone Zonesets command: SANbox2 #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ---------------------------------zone_set_1 B-96 59042-07 A
0 B – Command Line Interface Zoneset Command Zoneset Command Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit session. Refer to the “Zoning Command” on page B-99 for information about starting a Zoning Edit session. The Active, List, and Zones keywords are available without an Admin session. You must close the Zoning Edit session before using the Activate and Deactivate keywords.
0 B – Command Line Interface Zoneset Command list Displays a list of all zone sets. This keyword does not require an Admin session. remove [zone_set] [zone_list] Removes a list of zones given by [zone_list] from the zone set given by [zone_set]. Use a to delimit zone names in [zone_list]. If [zone_set] is the active zone set, the zone will not be removed until the zone set has been deactivated.
0 B – Command Line Interface Zoning Command Zoning Command Opens a Zoning Edit session in which to create and manage zone sets and zones. Refer to the “Zone Command” on page B-93 and the “Zoneset Command” on page B-97. Authority Admin session except for the Active, History, Limits, and List keywords. Syntax zoning active cancel clear edit history limits list restore save Keywords active Displays information for the active zone set including component zones and zone members.
0 B – Command Line Interface Zoning Command limits Displays the number of zone sets, zones, aliases, members per zone, members per alias, and total members in the zoning database. This keyword also displays the switch zoning database limits, excluding the active zone set, which are described in Table B-17. This keyword does not require an Admin session. Table B-17.
0 Examples B – Command Line Interface Zoning Command The following is an example of the Zoning Edit command: SANbox2 #> admin start SANbox2 (admin) #> zoning edit SANbox2 (admin-zoning) #> . . SANbox2 (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
0 B – Command Line Interface Zoning Command The following is an example of the Zoning List command: SANbox2 #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:
0 B – Command Line Interface Zoning Command wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15: 59042-07 A B-103
B – Command Line Interface Zoning Command 0 Notes B-104 59042-07 A
Glossary Access Control List Zone Access Control List zoning divides the fabric for purposes of controlling discovery and inbound traffic. Arbitrated Loop A Fibre Channel topology where ports use arbitration to establish a point-to-point circuit. Active Zone Set The zone set that defines the current zoning for the fabric. Arbitrated Loop Physical Address (AL_PA) A unique one-byte value assigned during loop initialization to each NL_Port on a loop.
0 SANbox2-8c Fibre Channel Switch Installation Guide Class 3 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports without acknowledgment. Configured Zone Sets The zone sets stored on a switch excluding the active zone set. Default Visibility Zoning parameter that determines the level of communication among ports/devices when there is no active zone set. Domain ID User defined number that identifies the switch in the fabric.
0 FRU Field Replaceable Unit Heartbeat LED A chassis LED that indicates the status of the internal switch processor and the results of the Power-On Self-Test. Inactive Firmware The firmware image on the switch that is not in use. Inband Management The ability to manage a switch through another switch over an inter-switch link. Initiator The device that initiates a data exchange with a target device.
0 SANbox2-8c Fibre Channel Switch Installation Guide NL_Port Node Loop Port. A Fibre Channel device port that supports arbitrated loop protocol. N_Port Node Port. A Fibre Channel device port in a point-to-point or fabric connection. NTP Network Time Protocol Over Temperature LED A chassis LED or a power supply LED that indicates that the switch or power supply is overheating. Pending Firmware The firmware image that will be activated upon the next switch reset.
0 SANbox2-8c Fibre Channel Switch Installation Guide Zone Set A set of zones grouped together. The active zone set defines the zoning for a fabric. Zoning Database The set of zone sets, zones, and aliases stored on a switch.
SANbox2-8c Fibre Channel Switch Installation Guide 0 Notes Glossary-6 59042-07 A
Index Numerics 10/100 Base-T straight cable 4-5 A access 3-2 Access Control List zone 3-3 account name display B-92 factory 3-11, B-1 ftp 5-4 maintenance mode 5-11 Activity LED 2-6, 2-8 Admin account name B-7 authority B-7 Admin command B-8 administrative state port B-51 switch B-36 air flow 2-10, A-4 alarm configuration B-43 configuration display B-73 log B-35, B-58 alias add members B-9 copy B-9 create B-9 delete B-9 delete members B-10 display list B-9 display members B-10 rename B-10 Alias command B-9
0 SANbox2-8c Fibre Channel Switch Installation Guide save B-12 controls 2-2 Create Support command B-14 credits 3-4, A-2 critical error 5-1 D Date command B-16 device cabling 4-21 description 3-1 performance 3-6 diagnostics 5-1, 5-9, A-2 dimensions A-3 disk space 4-1 distance 3-4 domain ID description 3-7 display B-59 lock 3-7 donor port 3-4, B-59 E E_Port 2-8, 5-6 emissions standards A-4 environmental conditions 4-2 specifications A-4 Ethernet direct connection 4-5 indirect connection 4-5 port 2-8 even
0 SANbox2-8c Fibre Channel Switch Installation Guide GBIC - See GigaBit Interface Converter generic ports 2-7 Gigabit Interface Converter 3-1 GL_Port 2-7 H Hardreset command B-18 harmonics A-4 HBA - See Host Bus Adapter Heartbeat LED 2-4, 5-2 heat output A-3 Help command B-19 History command B-20 host bus adapter 3-1, B-59 Hotreset command B-21 humidity 4-2, A-4 HyperTerminal application 4-6 I I/O Stream Guard B-40 Image command B-22 immunity A-4 inactivity timeout B-55 inband management 3-11 Input Powe
0 SANbox2-8c Fibre Channel Switch Installation Guide configuration reset B-31 interfaces B-59 Network Time Protocol client B-55 server B-55 new features 1-2 non-critical error 5-1 non-disruptive activation 4-21, B-21 NTP - See Network Time Protocol null modem F/F DB9 cable 4-5 O online test B-85 operating systems 4-1 Over Temperature LED 5-9 P page break B-35 Passwd command B-26 password change B-26 factory 3-11 file reset 5-13 maintenance mode 5-11 restore default 5-13 switch B-26 user account B-1 perf
0 SANbox2-8c Fibre Channel Switch Installation Guide S safety standards A-4 SANmark A-4 SANsurfer Switch Manager API 2-11 description 2-10 start 4-16 web applet 2-11, B-55 SANsurfer Switch Manager installation Linux 4-9, 4-12 Solaris 4-9, 4-14 Windows 4-8, 4-10 scalability A-1 serial port 2-9, 4-5, 4-6 Set command B-35 Set Config command B-37 Set Log command B-48 Set Port command B-51 Set Setup command B-53 SFP - See Small Form-Factor Pluggable shock A-4 Show command B-58 Show Config command B-73 Show Log
0 SANbox2-8c Fibre Channel Switch Installation Guide fluctuations A-4 operating A-3 W web applet description 2-11 enable B-55 Whoami command B-92 workstation 4-1, 4-5 configuration 4-6 IP address 4-6 worldwide name 3-2 WWN - See Worldwide Name display zones B-94 rename B-98 Zoneset command B-97 zoning configuration B-44 configuration display B-73 database 3-2, B-31 edit B-99 history B-99 limits 3-2, B-100 list definitions B-100 revert changes B-100 save edits B-100 Zoning command B-99 Z zone access con
