QUICK START GUIDE [ Quick Start Guide ] INTELLIGENT STORAGE ROUTER INSTALLATION iSR6152 z
Purchasers of OEM products should consult with the OEM for support. Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods: Web http://support.qlogic.com E-mail support@qlogic.com The QLogic knowledge database contains troubleshooting information for the QLogic adapters. Access the database from the QLogic Support Web page, http://support.qlogic.com.
Quick Start Guide The iSR6152 is an intelligent Storage RouterTM that provides remote and local SAN island connectivity. The major applications are: ■ Remote data replications between Fibre Channel storage arrays. ■ Connecting remote Fibre Channel servers to local Fibre Channel storage. Suggested Configurations Figure 1 shows connecting Local Array 1 to Remote Array 2, and the server from a local SAN to storage from a remote SAN.
Installation Instructions This quick start guide provides procedures for installing and configuring your new QLogic iSR6152 Router. ■ Step 1. Verify the package contents. ■ Step 2. Complete the pre-installation checklist. ■ Step 3. Mount the router. ■ Step 4. Install the small form-factor pluggable (SFP) transceivers. ■ Step 5. Apply power to the iSR6152 Router. ■ Step 6. Download and Install SANsurfer Router Manager. ■ Step 7. Configure the iSR6152 management port IP address. Step 1.
Table 1. Worksheet for Router (Continued) IP Address: GbE Port 3 (GE3) Subnet Mask: Gateway: IP Address: GbE Port 4 (GE4) Subnet Mask: Gateway: Step 3. Mount the Router Place the router on a flat surface, mount it in a standard 19-inch Electronic Industries Association (EIA) rack, or mount it on the optionally available shelf. Step 4. Install the SFP Transceivers An SFP transceiver is required for each of the router’s Fibre Channel ports that will be connected to a Fibre Channel device or switch.
Step 6. Download and Install SANsurfer Router Manager Follow these steps to download the SANsurfer Router Manager utility from the QLogic Web site to a PC workstation and then install it: 1. Close all programs currently running. 2. Go to the QLogic Downloads and Documentation page: http://driverdownloads.qlogic.com 3. Under Downloads– QLogic Products, type iSR6152 in the search box. 4.
press 'q' or 'Q' and the ENTER key to do so. WARNING: The following command might cause a loss of connections to the MGMT port. 7. At the CLI prompts, configure the router addresses as follows: a. At the IPv4 Interface (0=Enable, 1=Disable) prompt, enter 0 to enable this option. b. At the IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) prompt, enter 0 to select the Static mode (recommended). c. At the IPv4 Address, IPv4 Subnet Mask, and IPv4 Gateway prompts, enter the IP addresses for these items. d.
Warranty The QLogic iSR6152 Router comes with a standard one-year QLogic warranty, or as specified by other agreements. For warranty details, see the QLogic Web site at www.qlogic.com. Regulatory Information (Preliminary) The following sections contain a summary of EMC/EMI test specifications performed on the QLogic iSR6152 Router to comply with radiated emission, radiated immunity, and product safety standards. Safety Standards UL60950 (USA) CSG 22.2 No.
© 2011 QLogic Corporation. QLogic, the QLogic logo, intelligent Storage Router, and SANsurfer are trademarks or registered trademarks of QLogic Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure.
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.
