D Simplify SANbox2-64 Switch Management User’s Guide 59048-04 Rev.
D SANbox2-64 Switch Management User’s Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Section 1 Introduction 1.1 1.2 1.3 1.4 1.4.1 1.4.2 1.4.3 Intended Audience ............................................................................................. 1-1 Related Materials ............................................................................................... 1-1 JDOM License.................................................................................................... 1-2 Technical Support..................................................................
SANbox2-64 Switch Management User’s Guide D 2.13.4 2.13.5 2.13.6 2.14 2.14.1 2.14.2 2.14.2.1 2.14.2.2 2.14.3 2.14.4 2.15 2.15.1 2.15.2 2.15.3 2.15.3.1 2.15.3.2 2.15.4 Graphic Window ...................................................................................... 2-24 Data Window and Tabs............................................................................ 2-24 Working Status Indicator.......................................................................... 2-24 Using the Topology Display ..
D SANbox2-64 Switch Management User’s Guide 3.4 3.4.1 3.4.1.1 3.4.1.2 3.4.1.3 3.4.1.4 3.4.1.5 3.4.2 3.4.2.1 3.4.2.2 3.4.3 3.4.4 3.4.4.1 3.4.4.2 3.4.4.3 3.4.5 3.4.5.1 3.4.5.2 3.4.5.3 3.4.5.4 3.4.5.5 3.4.5.6 3.4.6 3.4.6.1 3.4.6.2 3.4.6.3 3.4.6.4 3.4.6.5 3.4.6.6 3.4.6.7 3.4.6.8 3.4.7 3.4.7.1 3.4.7.2 3.4.7.3 3.4.8 Zoning a Fabric ................................................................................................ 3-13 Zoning Concepts ...............................................................
SANbox2-64 Switch Management User’s Guide D 4.1.2 4.1.3 4.1.4 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.9.1 4.9.2 4.9.2.1 4.9.2.2 4.9.2.3 4.9.2.4 4.9.2.5 4.9.2.6 4.9.2.7 4.9.2.8 4.9.2.9 4.9.3 4.9.3.1 4.9.3.2 4.9.3.3 4.9.3.4 4.10 4.11 4.12 4.13 4.13.1 Removing a User Account......................................................................... 4-4 Changing a User Account Password......................................................... 4-5 Modifying a User Account.....
D SANbox2-64 Switch Management User’s Guide 4.13.2 4.13.3 4.13.4 Activating the Pending Firmware............................................................. 4-35 Changing the Pending Firmware ............................................................. 4-35 Displaying Hardware Status .................................................................... 4-36 Section 5 Managing I/O Blades 5.1 5.2 5.3 5.4 5.5 Displaying I/O Blade Information..............................................................
SANbox2-64 Switch Management User’s Guide D Alias Command .........................................................................................A-8 Config Command.....................................................................................A-10 Date Command .......................................................................................A-13 Fallback Command..................................................................................A-14 Hardreset Command .............................
D B.5 B.6 B.7 B.7.1 B.7.2 B.8 B.9 B.10 SANbox2-64 Switch Management User’s Guide Setting SANsurfer Fabric View Preferences ......................................................B-4 Setting the Polling Frequency ............................................................................B-5 Displaying Graphs ..............................................................................................B-5 Arranging Graphs in the Display................................................................
D SANbox2-64 Switch Management User’s Guide 2-12 2-13 2-14 2-15 3-1 3-2 3-3 3-4 3-5 3-6 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 6-1 6-2 6-3 6-4 B-1 B-2 B-3 B-4 B-5 Faceplate Display Menu............................................................................................... 2-19 Fabric Tree................................................................................................................... 2-23 Topology Display.....................................................
D 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 5-1 5-2 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 A-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 A-10 A-11 A-12 A-13 A-14 A-15 A-16 C-1 C-2 C-3 C-4 C-5 C-6 C-7 C-8 C-9 SANbox2-64 Switch Management User’s Guide FDMI Data Window Entries............................................................................................ 4-9 Switch Data Window Entries ........................................................................................ 4-10 Switch Resets .....................
SANbox2-64 Switch Management User’s Guide C-10 C-11 C-12 C-13 C-14 Page xii D Extended Credits Wizard Messages ............................................................................C-17 Zoning Dialog Messages..............................................................................................C-17 Restore Configuration Dialog Messages......................................................................C-20 Save Fabric View Messages..........................................................
Section 1 Introduction This manual describes the switch management tools which include the SANbox Manager™ application (version 4.00) and the Command Line Interface (CLI) for the SANbox2®-64 Fibre Channel switch (firmware version 4.0). The SANbox Manager switch management application is the primary focus of this manual which is organized as follows: Section 1 describes the intended audience for this manual, related materials, and technical support.
D 1 – Introduction JDOM License 1.3 JDOM License This product includes software developed by the JDOM Project (http://www.jdom.org/). Copyright (C) 2000-2002 Brett McLaughlin & Jason Hunter. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions, and the following disclaimer. 2.
D 1 – Introduction Technical Support 1.4 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates. 1.4.
1 – Introduction Technical Support D Notes 1-4 59048-04 Rev.
Section 2 Using SANbox Manager This section describes how to use the SANbox Manager application and its menus.
D 2 – Using SANbox Manager Installing SANbox Manager Your switch was shipped with either a SANsurfer Management Suite Disk or a SANbox2 Installation Disk.
D 2 – Using SANbox Manager Installing SANbox Manager 2.1.2 SANsurfer Management Suite Disk - Linux Installation To install the SANsurfer application on Linux from the SANsurfer Management Suite Disk, do the following: 1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If a file browser dialog opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Management Suite start page.
D 2 – Using SANbox Manager Installing SANbox Manager 2.1.3 SANsurfer Management Suite Disk - Solaris Installation To install the SANsurfer application on Solaris from the SANsurfer Management Suite CD-ROM, do the following: 1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If the SANsurfer Management Suite start page does not open in your default browser, do the following: a. Right-click the Workspace Menu. b. Select File, then select File Manager. c.
D 2 – Using SANbox Manager Starting SANsurfer Management Suite 2.2 Starting SANsurfer Management Suite To start the SANsurfer application for the first time, choose one of the following methods: For a Windows platform, double-click the SANsurfer shortcut, or select SANsurfer from Start menu, depending on how you installed the SANsurfer application. From a command line, you can enter the SANsurfer command: \SANsurfer.
2 – Using SANbox Manager Exiting SANsurfer Management Suite D Click the Open Existing Fabric radio button to open the Add a New Fabric dialog, which prompts you for a fabric name, IP address, account name, and password. Refer to ”Adding a Fabric” on page 3-3. Click the Open Existing Fabric View File radio button to open the Open View dialog which prompts you to specify a fabric view file that you saved earlier. Refer to ”Opening a Fabric View File” on page 3-4.
D 2 – Using SANbox Manager Exiting SANsurfer Management Suite In the Save Default Fabric View File dialog, enter an encryption key in the Default Fabric File Encryption Key field. Re-enter the encryption key in the Re-enter Encryption Key to Confirm field. Click the OK button to save the current set of fabrics to the default fabric view file in the working directory.
D 2 – Using SANbox Manager Uninstalling SANsurfer Management Suite 2.4 Uninstalling SANsurfer Management Suite A program to uninstall SANsurfer was installed as part of the SANsurfer installation process. The Uninstall Data folder in the contains the uninstall program (Uninstall SANsurfer).
D 2 – Using SANbox Manager Uninstalling SANsurfer Management Suite 2.4.2 SANbox Manager Installation Disk - Linux Installation To install the SANbox Manager application on Linux from the SANbox Manager Installation Disk, do the following: 1. Insert the SANbox2 Installation Disk into the management workstation CD-ROM drive. If a file browser does not open, double-click the CD-ROM icon to open the browser. Double click the SANbox_Manager folder, then double click the Linux folder.
D 2 – Using SANbox Manager Starting SANbox Manager 2.5 Starting SANbox Manager To start the SANbox Manager application for the first time, choose one of the following methods: For a Windows platform, double-click the SANbox Manager shortcut, or select SANbox Manager from Start menu, depending on how you installed the SANbox Manager application. From a command line, you can enter the SANbox_Manager command: SANbox_Manager.
D 2 – Using SANbox Manager Exiting SANbox Manager Click the Open Existing Fabric View File radio button to open the Open View dialog which prompts you to specify a fabric view file that you saved earlier. Refer to ”Opening a Fabric View File” on page 3-4. Click the Start Application Without Specifying a Fabric radio button to open the SANbox Manager window without displaying any fabric, as shown in Figure 2-6. Figure 2-6. SANbox Manager Window 2.
D 2 – Using SANbox Manager Exiting SANbox Manager To prevent SANbox Manager from prompting you to save the default fabric view file between SANbox Manager sessions, set the View File Auto Save and Load preferences setting to Enable (default). Refer to ”Setting SANbox Manager Preferences” on page 2-14 for more information. Figure 2-7.
D 2 – Using SANbox Manager Uninstalling SANbox Manager 2.7 Uninstalling SANbox Manager A program to uninstall SANbox Manager was installed as part of the SANbox Manager installation process. The Uninstaller Data folder in the Install folder contains the uninstall program (Uninstall SANbox Manager). Also, a shortcut/link to the uninstall program was installed in the installation directory during the SANbox Manager installation process.
D 2 – Using SANbox Manager Saving and Opening Fabric View Files 2.9 Saving and Opening Fabric View Files A fabric view file is one or more fabrics saved to a file. In addition to the SANbox Manager default fabric view file, you can save and open your own fabric view files. To save a set of fabrics to a file, do the following: 1. Open the File menu and select Save View As to open the Save View dialog. 2. Enter a name for the fabric file or click the Browse button to select an existing file.
D 2 – Using SANbox Manager Setting SANbox Manager Preferences Enable (default) or disable the Event Browser. Refer to ”Displaying the Event Browser” on page 3-9. If the Event Browser is enabled using the Preferences dialog, the next time SANbox Manager is started, all events from the switch alarm log will be displayed. If the Event Browser is disabled when SANbox Manager is started and later enabled, only those events from the time the Event Browser was enabled and forward will be displayed.
2 – Using SANbox Manager Using Online Help D 2.11 Using Online Help Online help is available for the SANbox Manager application and its functions. The two ways to open the online help file are: open the Help menu and select Help Topics, or click the Help button in the tool bar. You can also display context-sensitive help for all SANbox Manager dialogs by clicking the Help button in the dialog. 2.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13 SANbox Manager User Interface The SANbox Manager application uses two basic displays to manage the fabric and individual switches: the topology display and the faceplate display. The topology display shows all switches that are able to communicate and all connections between switches. The faceplate display shows the front of a single switch and its ports. Both displays share some common elements as shown in Figure 2-10.
2 – Using SANbox Manager SANbox Manager User Interface D 2.13.1 Menu Bar The SANbox Manager menus and the tasks offered in them vary depending on the display. For example, the Port menu and many of the Switch menu selections are only available in the faceplate display. 2.13.1.1 Topology Display Menu The menu options in the topology display are shown below. Figure 2-11. Topology Display Menu 2-18 59048-04 Rev.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13.1.2 Faceplate Display Menu The menu options in the faceplate display are shown below. Figure 2-12. Faceplate Display Menu The keyboard shortcut keys vary by display type: topology display and faceplate display. In addition to the menu bar, both the topology and faceplate displays have context sensitive menus that pop up when you right-click on the switches and links in the topology display, and on the switch image in the faceplate display.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13.1.3 Topology Display Shortcut Keys The shortcut keys for the topology display are below. The shortcut key combinations are not case-sensitive. Table 2-2.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13.1.4 Faceplate Display Shortcut Keys The shortcut keys for the faceplate displays are shown in below. The shortcut key combinations are not case-sensitive. Table 2-3. Faceplate Display Menu Shortcut Keys Shortcut 59048-04 Rev.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13.2 Tool Bar The tool bar consists of a row of graphical buttons that you can use to access SANbox Manager functions as shown in Table 2-4. The tool bar buttons are an alternative method to using the menu bar. The tool bar can be relocated in the display by clicking and dragging the handle at the left edge of the tool bar. Table 2-4. Tool Bar Buttons Tool Bar Button Description Add Fabric button - adds a new fabric to the fabric view.
D 2 – Using SANbox Manager SANbox Manager User Interface 2.13.3 Fabric Tree The fabric tree lists the managed fabrics and their switches as shown in Figure 2-13. The window width can be adjusted by clicking and dragging the moveable window border. An entry handle located to the left of an entry in the tree indicates that the entry can be expanded or collapsed. Click this handle or double-click the entry to expand or collapse a fabric tree entry. A fabric entry expands to show its member switches.
2 – Using SANbox Manager SANbox Manager User Interface D The fabric tree provides access to the topology and faceplate displays for any fabric or switch. To open the topology display from the fabric tree, click a fabric entry. To open the faceplate display from the fabric tree, click a switch entry. 2.13.4 Graphic Window The graphic window, as shown in Figure 2-10, presents graphic information about fabrics and switches such as the fabric topology and the switch faceplate.
D 2 – Using SANbox Manager Using the Topology Display 2.14 Using the Topology Display The topology display shown in Figure 2-14 receives information from the selected fabric and displays its topology. Switches and inter-switch links (ISLs) appear in the graphic window and use color to indicate status. Consider the following topology display features: Switch and link status Working with switches and links Topology data windows Figure 2-14. Topology Display 2.14.
2 – Using SANbox Manager Using the Topology Display D 2.14.2 Working with Switches and Links Switch and link icons are selectable and moveable, and serve as access points for other displays and menus. You select switches and links to display information about them, modify their configuration, or delete them from the display. Context-sensitive popup menus are displayed when you right-click on a switch or link icon, or in the background of the topology display and graphic window. 2.14.2.
D 2 – Using SANbox Manager Using the Topology Display 2.14.3 Opening the Faceplate Display and Topology Popup Menus The faceplate display shows the front of a single switch and its ports. To open the faceplate display when viewing the topology display, click the switch entry/icon in the fabric tree, or double-click the switch graphic. The topology display also offers a fabric, switch, and a link popup menu: To open the fabric popup menu, right-click the graphic window background.
D 2 – Using SANbox Manager Using the Faceplate Display 2.15 Using the Faceplate Display The faceplate display shown in Figure 2-15 displays the switch name and operational state, and port status. Consider the following functional elements of the faceplate display: I/O blades Port views and status Working with ports Working with I/O blades and ports Faceplate data windows Figure 2-15. Faceplate Display 2-28 59048-04 Rev.
D 2 – Using SANbox Manager Using the Faceplate Display 2.15.1 I/O Blades Figure 2-15 shows how slots appear in the faceplate display with and without installed I/O blades. I/O blade failure status is indicated by a status icon as shown in Figure 2-15. The SANbox2-64 switch numbers its slots from 0–10 from left to right. I/O blades occupy slots 1–4 and 6–9. Ports on an I/O blade are numbered from 0–7 from top to bottom in slot 1, 8–15 in slot 2, and so on to 56–63 in slot 9.
D 2 – Using SANbox Manager Using the Faceplate Display To select all I/O blades or ports, right-click anywhere in the graphic window. Select Select All Blades or Select All Ports from the popup menu. To cancel a selection, press and hold the Control key and select it again. 2.15.3.2 Opening the Faceplate Popup Menu To open the popup menu, right-click on the faceplate image to present the following tasks.
D 2 – Using SANbox Manager Using the Faceplate Display 59048-04 Rev. B Configured Zonesets – displays all zone sets, zones, and zone membership in the zoning database.
2 – Using SANbox Manager Using the Faceplate Display D Notes 2-32 59048-04 Rev.
Section 3 Managing Fabrics This section describes the following tasks that manage fabrics: Securing a fabric Managing the fabric database Displaying fabric information Zoning a fabric 3.1 Fabric Security The components of Fibre Channel fabric security are: User account security Fabric services 3.1.1 User Account Security User account security is the process by which your user account and password are authenticated with the list of valid user accounts and passwords.
D 3 – Managing Fabrics Fabric Security Manager grants access to its menus according to your authority level. If you do not have Admin authority, you are limited to monitoring tasks. Note: If a user is logged into a switch using SANbox Manager or CLI, and an administrator changes user access rights, passwords, or UserAuthentication security settings, existing logins will not be affected by the new settings. Login access and privileges are only checked for a new login request. 3.1.
D 3 – Managing Fabrics Managing the Fabric Database 3.1.2.2 Enabling In-band Management To enable In-band Management, do the following: 1. On the faceplate display, open the Switch menu and select Switch Properties to open the Switch Properties dialog. 2. Click the In-band Management Enable button. 3. Click the OK button to save the change to the database. 3.2 Managing the Fabric Database A fabric database contains the set of fabrics that you have added during a SANbox Manager session.
D 3 – Managing Fabrics Managing the Fabric Database 4. Refer to ”User Account Security” on page 3-1 for information about user authentication. Refer to ”Managing User Accounts” on page 4-1 or the ”User Command” on page A-83 for information about creating user accounts. Click the Add Fabric button.
D 3 – Managing Fabrics Managing the Fabric Database 3.2.4 Saving a Fabric View File To save a view file, do the following: 1. Open the File menu, and select Save View As. 2. In the Save View dialog, enter a new file name. 3. Enter a file password, if necessary. 4. Click the OK button. 3.2.5 Rediscovering a Fabric After making changes to or deleting switches from a fabric view, it may be helpful to again view the actual fabric configuration.
D 3 – Managing Fabrics Managing the Fabric Database 5. Configure the port types for the new switch using the Port Properties dialog. The ports can be G_Port, GL_Port, F_Port, FL_Port, or Donor. 6. Connect the devices to the switch. 7. Make any necessary zoning changes using the Edit Zoning dialog. To open the Edit Zoning dialog, open the Zoning menu, and select Edit Zoning. If you changed the Default Visibility setting in the Zoning Config dialog from All to None, change that setting back to All.
D 3 – Managing Fabrics Displaying Fabric Information c. In the Restore dialog, enter the archive file from the failed switch or browse for the file. d. Click the Restore button. 5. Reset the replacement switch to activate the configuration formerly possessed by the failed switch including the domain ID and the zoning database. Open the Switch menu and select Reset Switch. 6.
D 3 – Managing Fabrics Displaying Fabric Information Press the F5 key. Right-click anywhere in the background of the topology display and select Refresh Fabric from the popup menu. The topology display uses switch and status icons to provide status information about switches, inter-switch links, and the Ethernet connection. The switch status icons, displayed on the left side of a switch, vary in shape and color.
D 3 – Managing Fabrics Displaying Fabric Information 3.3.2 Displaying the Event Browser The Event Browser displays a list of recorded events and alarms generated by the switches in the fabric and the SANbox Manager application. Events are generated by the SANbox Manager application and are not saved on the switch, but can be saved to a file during the SANbox Manager session.
D 3 – Managing Fabrics Displaying Fabric Information Browser preference. Refer to ”Setting SANbox Manager Preferences” on page 2-14. Severity is indicated in the severity column using icons as described in Table 3-2. Note: The alarm log is cleared out when the switch is reset or power cycled and that the user should save these log files off if they want to keep the data. Refer to ”Set Log Command” on page A-44 for information about saving the alarm log to a file.
D 3 – Managing Fabrics Displaying Fabric Information 3.3.2.1 Filtering the Event Browser Filtering the Event Browser enables you to display only those events that are of interest based on the event severity, timestamp, source, type, and description. To filter the Event Browser, open the Filter menu and select Filter Entries. This opens the Filter Events dialog shown in Figure 3-3. The Event Browser displays those events that meet all of the criteria in the Filter Events dialog.
D 3 – Managing Fabrics Displaying Fabric Information 3.3.2.2 Sorting the Event Browser Sorting the Event Browser enables you to display the events in alphanumeric order based on the event severity, timestamp, source, type, or description. Initially, the Event Browser is sorted in ascending order by timestamp. To sort the Event Browser, click the Severity, Timestamp, Source, Type, or Description column buttons.
D 3 – Managing Fabrics Zoning a Fabric Figure 3-4. Active Zone Set Data Window 3.4 Zoning a Fabric Zoning enables you to divide the ports and devices of the fabric into zones for more efficient and secure communication among functionally grouped nodes.
D 3 – Managing Fabrics Zoning a Fabric Zone sets Zoning database Zoning configuration 3.4.1.1 Zones A zone is a named group of ports or devices that can communicate with each other. Devices within a zone can only communicate with other devices in the same zone. A device may participate in more than one zone. Membership in a zone can be defined by switch domain ID and port number, device Fibre Channel address, or device World Wide Name (WWN).
D 3 – Managing Fabrics Zoning a Fabric 3.4.1.1.2 Access Control List Hard Zones Access Control List (ACL) zoning divides the fabric for purposes of controlling discovery and inbound traffic. ACL zoning is a type of hard zoning that is hardware enforced. This type of zoning is useful for controlling access to certain devices without totally isolating them from the fabric. Devices can communicate with each other and transmit outside the ACL zone, but cannot receive inbound traffic from outside the zone.
D 3 – Managing Fabrics Zoning a Fabric made on an individual switch basis and are not propagated to other switches in the fabric when saved. The zoning limits for a fabric are as follows: MaxZoneSets is 256. The maximum number of zone sets that can be configured on the switch. This will be enforced during the configuration of zoning and during a zoning database merge from the fabric. MaxZones is 256. The maximum number of zones that can be configured on the switch.
D 3 – Managing Fabrics Zoning a Fabric 3.4.2 Using the Zoning Config Dialog Use the Zoning Config dialog to change the Auto Save and Default Visibility configuration parameters. In the faceplate display, open the Zoning menu and select Edit Zoning Config to open the Zoning Config dialog shown in Figure 3-5. After making changes, click the OK button to put the new values into effect. Figure 3-5. Zoning Config Dialog 3.4.2.
D 3 – Managing Fabrics Zoning a Fabric CAUTION! This command will deactivate the active zone set. To restore the default zoning for a switch: 1. In the faceplate display, open the Zoning menu and select Restore Default Zoning. 2. Click the OK button to confirm that you want to restore default zoning and save changes to the zoning database. 3.4.4 Merging Fabrics and Zoning If you join two fabrics with an inter-switch link, the active zone sets from the two fabrics attempt to merge automatically.
D 3 – Managing Fabrics Zoning a Fabric Note: If you deactivate the active zone set in one fabric and the Auto Save parameter is enabled, the active zone set from the second fabric will propagate to the first fabric and replace all zones with matching names in the configured zone sets. If the zone sets to merge have the same Zone A that only differ in the type of zone (soft vs. ACL), the zone sets will merge.
D 3 – Managing Fabrics Zoning a Fabric To apply zoning to a fabric, choose a zone set and activate it. When you activate a zone set, the switch distributes that zone set and its zones, excluding aliases, to every switch in the fabric. This zone set is known as the active zone set. You can not edit an active zone set on a switch. You must configure an inactive zone set to your needs and then activate that updated zone set to apply the changes to the fabric.
D 3 – Managing Fabrics Zoning a Fabric Table 3-3.
D 3 – Managing Fabrics Zoning a Fabric 3.4.5 Managing Zone Sets Zoning a fabric involves creating a zone set, creating zones as zone set members, then adding devices as zone members. The zoning database supports multiple zone sets to serve the different security and access needs of your storage area network, but only one zone set can be active at one time.
D 3 – Managing Fabrics Zoning a Fabric 3.4.5.2 Activating and Deactivating a Zone Set You must activate a zone set to apply its zoning definitions to the fabric. Only one zone set can be active at one time. When you activate a zone set, the switch distributes that zone set to the temporary zoning database on every switch in the fabric.
D 3 – Managing Fabrics Zoning a Fabric 3.4.5.5 Removing a Zone Set Removing a zone set from the database affects the member zones in the following ways. Member zones that are members of other zone sets are not affected. Member zones that are not members of other zone sets become members of the orphan zone set. The orphan zone set is not saved on the switch. To delete a zone set from the database, do the following: 1.
D 3 – Managing Fabrics Zoning a Fabric Note: Changes that you make to the zoning database are limited to the managed switch and do not propagate to the rest of the fabric. To distribute changes to configured zone sets fabric wide, you must edit the zoning databases on the individual switches. 3.4.6.1 Creating a Zone in a Zone Set When a zone is created, its zone type is soft. To change the zone type to a hard zone, refer to ”Changing Zone Types” on page 3-28 for more information.
D 3 – Managing Fabrics Zoning a Fabric 3.4.6.2 Adding Zone Members Adding a zone member to a zone will affect every zone set in which that zone is a member. To add member ports/devices to a zone, do one of the following: Select a port by port number, Fibre Channel address, or World Wide Name in the Port/Device tree, and drag it into the zone. To select and drag multiple ports/devices, press and hold the Control key while dragging.
D 3 – Managing Fabrics Zoning a Fabric 3.4.6.4 Renaming a Zone or a Zone Set To rename a zone, do the following: 1. In the Zone Sets tree of the Edit Zoning dialog, click the zone/zone set to be renamed. 2. Open the Edit menu and select Rename. 3. In the Rename Zone/Rename Zone Set dialog, enter a new name for the zone/zone set. 4. Click the OK button. 3.4.6.5 Removing a Zone Member Removing a zone member will affect every zone and zone set in which that zone is a member.
D 3 – Managing Fabrics Zoning a Fabric 3.4.6.8 Changing Zone Types To change a zone type, do the following: 1. In the faceplate display, select the switch with the zone type to change. 2. Click the Zoning button to open the Edit Zoning dialog. 3. In the Zone Sets tree, select the zone to change. 4. Open the Edit menu and select Set Zone Type to open the Set Zone Type dialog. 5. Open the Zone Type pull-down menu and select Soft or ACL. Soft zoning is the least restrictive type of zoning.
D 3 – Managing Fabrics Zoning a Fabric 3.4.7.2 Adding a Member to an Alias You can add a member to an alias in the following ways: Drag-and-drop method. Select the alias in the left pane and the member in the right pane to add to that alias, and click the Insert button. Select the alias in the left pane and the member in the right pane to add to that alias, and open the Edit menu and select Add Members. To add a member to an alias using the drag-and-drop method, do the following: 1.
D 3 – Managing Fabrics Zoning a Fabric 3.4.8 Saving the Zoning Database to a File You can save the zoning database to an XML file. You can later reload this zoning database on the same switch or another switch. To save a zoning database to a file, do the following: 3-30 1. In the faceplate display, open the Zoning menu, and select Edit Zoning. 2. In the Edit Zoning dialog, open the File menu and select Save As. 3. In the Save dialog, enter a file name for the database file. 4.
Section 4 Managing Switches This section describes the following tasks that manage switches in the fabric.
D 4 – Managing Switches Managing User Accounts Table 4-1. Factory User Accounts Account Name Password Admin Authority Expiration admin admin true never expires images images false never expires The Admin account is the only user that can manage all user accounts with the User Account Administration dialogs. The Admin account can create, remove, or modify user accounts, and change account passwords. The Admin account can also view and modify the switch and its configuration with SANbox Manager.
D 4 – Managing Switches Managing User Accounts 4.1.1 Creating User Accounts To create a user account on a switch, open the Switch menu in the faceplate display and select User Accounts.... This displays the User Account Administration dialog shown in Figure 4-1. A switch can have a maximum of 15 user accounts. Figure 4-1. User Account Administration Dialog – Add Account 1. To open the User Account Administration dialogs, open the Switch menu in the faceplate display, and select User Accounts.... 2.
4 – Managing Switches Managing User Accounts D 4.1.2 Removing a User Account To remove a user account on a switch, open the Switch menu in the faceplate display and select User Accounts.... Click the Remove Account tab in the dialog to present the display shown in Figure 4-2. Select the account name from the list of accounts at the top of the dialog and click the Remove Account button. Figure 4-2. User Account Administration Dialog – Remove Account 4-4 59048-04 Rev.
D 4 – Managing Switches Managing User Accounts 4.1.3 Changing a User Account Password To change the password for an account on a switch, open the Switch menu in the faceplate display and select User Accounts.... Click the Change Password tab in the dialog to present the display shown in Figure 4-3. Select the account name from the list of accounts at the top of the dialog, then enter the old password, the new password, and verify the new password in the corresponding fields.
4 – Managing Switches Managing User Accounts D 4.1.4 Modifying a User Account To modify a user account on a switch, open the Switch menu in the faceplate display and select User Accounts.... This displays the User Account Administration dialog shown in Figure 4-4. Click the Modify Account tab. Select the account name from the list of accounts at the top of the dialog. Click the Admin authority Enabled check box to grant admin authority to the account name. Click an Account Expiration Date radio button.
D 4 – Managing Switches Displaying Switch Information 4.2 Displaying Switch Information The faceplate display and data windows provide the following switch information: Name server information Device and HBA information Switch specifications and addresses Configuration parameters Performance statistics Port information Configured zone sets Figure 4-5 shows the faceplate display for the SANbox2-64 switch. Figure 4-5. Faceplate Display 59048-04 Rev.
D 4 – Managing Switches Displaying Switch Information The fabric updates the topology and faceplate displays by forwarding changes in status to the management workstation as they occur. You can allow the fabric to update the switch status, or you can refresh the display at any time. To refresh switch status in the display, do one of the following: Click the Refresh button. Open the View menu and select Refresh. Press the F5 key.
D 4 – Managing Switches Displaying Switch Information 4.2.2 FDMI Data Window The FDMI data window displays device information from the fabric and allows devices to register certain information with the fabric. To open the FDMI data window, open the topology display and click the FDMI tab below the window. SANbox Manager will report any and all FDMI information reported by the entry switch, if FDMI is enabled on the entry switch.
D 4 – Managing Switches Displaying Switch Information Figure 4-6. Detailed FDMI Display Dialog 4.2.3 Switch Data Window The Switch data window displays current network and switch information for the selected switches. Refer to ”Configuring a Switch” on page 4-20 for more information about the Switch data window. To open the Switch data window, select one or more switches in the topology display or open the faceplate display, and click the Switch tab below the window.
D 4 – Managing Switches Displaying Switch Information Table 4-4. Switch Data Window Entries (Continued) Entry 59048-04 Rev.
D 4 – Managing Switches Displaying Switch Information Table 4-4. Switch Data Window Entries (Continued) Entry 4-12 Description Legacy Address Format Legacy port addressing status. Enabled only for interoperability with non-FC-SW-2 switches. FC-SW-2 Auto Save Zoning auto save status. Saves zoning updates in temporary memory and the zoning database (True) or only in temporary memory (False). Zoning Default Visibility Zoning visibility status.
D 4 – Managing Switches Displaying Switch Information Table 4-4. Switch Data Window Entries (Continued) Entry Description FDMI HBA Entry Limit Maximum number of HBAs that can be registered with a switch. Number of Donor Groups Total number of donor port groups. A donor group is a set of ports on a switch that can donate buffer credits to each other. 4.2.4 Link Data Window The Link data window displays information about all switch links in the fabric or selected links.
4 – Managing Switches Displaying Switch Information D 4.2.6 Port Information Data Window The Port Information data window displays port detail information for the selected ports. To open the Port Statistics data window, click the Port Info tab below the data window in the faceplate display. Refer to Table 6-6 for a description of the Port Information data window entries. Figure 4-7. Faceplate Display - Port Information 4-14 59048-04 Rev.
D 4 – Managing Switches Displaying Switch Information 4.2.7 Configured and Active Zonesets Data Windows The Configured Zonesets data window displays all zone sets, zones, aliases, and zone membership in the zoning database, as shown in Figure 4-8. To open the Configured Zonesets data window, click the Configured Zonesets tab below the data window in the faceplate display.
4 – Managing Switches Configuring Port Threshold Alarms D 4.3 Configuring Port Threshold Alarms You can configure the switch to generate alarms for selected events. Configuring an alarm involves choosing an event type, rising and falling triggers, a sample window, and finally enabling or disabling the alarm. To configure port threshold alarms, do the following: 1. In the faceplate display, open the Switch menu and select Port Threshold Alarm Configuration.
D 4 – Managing Switches Configuring Port Threshold Alarms 5. Enter a value for the rising trigger. A rising trigger alarm is generated when the event count per interval exceeds the rising trigger. The switch will not generate another rising trigger alarm for that event until the count descends below the falling trigger and rises again above the rising trigger. Consider the example in Figure 4-10. 6. Enter a value for the falling trigger.
4 – Managing Switches Exporting Name Server Information to a File D 4.4 Exporting Name Server Information to a File To save name server information to a file, open the topology display and do the following: 1. Select one or more switches. If no switches are selected, name server information is gathered for all switches. 2. Open the Switch menu and select Export Name Server. 3. In the Save dialog, enter a file name. 4. Click the Save button. 4.
D 4 – Managing Switches Resetting a Switch 4.8 Resetting a Switch Resetting a switch reboots the switch using configuration parameters in memory. Depending on the reset type, a switch reset may or may not include a power-on self test or it may or may not disrupt traffic. Table 4-5 describes the types of switch resets. During a hotreset operation, fabric services will be unavailable for a short period (30-75 seconds depending on switch model).
D 4 – Managing Switches Configuring a Switch Table 4-5. Switch Resets Type Description Hot Reset Resets a switch without a power-on self test. This reset activates the pending firmware, but does not disrupt switch traffic. If errors are detected on a port during a hot reset, the port is reset automatically. Reset without POST Resets a switch without a power-on self test. This reset activates the pending firmware and it is disruptive to switch traffic.
D 4 – Managing Switches Configuring a Switch 4.9.1 Using the Configuration Wizard The Configuration Wizard is a series of dialogs you can use to configure the IP address and other basic parameters on new or replacement switches. SANbox Manager will detect the first time use and present the Initial Start dialog, from which the Configuration Wizard can be launched.
D 4 – Managing Switches Configuring a Switch Figure 4-11. Switch Properties Dialog 4.9.2.1 Symbolic Name The symbolic name is a user-defined name of up to 63 characters that identifies the switch. The symbolic name is used in the topology and faceplate displays, as well as many data windows to more easily identify switches. The illegal characters are the pound sign (#), semi-colon (;), and comma (,). 4.9.2.
D 4 – Managing Switches Configuring a Switch Table 4-6 describes the administrative state values. Table 4-6. Switch Administrative States Parameter Description Online The switch is available. Offline The switch is unavailable. Diagnostics The switch is in diagnostics mode, is unavailable, and tests can then be run on all ports of the switch. 4.9.2.3 Domain ID and Domain ID Lock The domain ID is a unique Fibre Channel identifier for the switch.
4 – Managing Switches Configuring a Switch D enabled on the entry switch. To view FDMI data, FDMI must be enabled on the entry switch and on all other switches in the fabric which are to report FDMI data. FDMI is comprised of the fabric-to-device interface and the application-to-fabric interface. The fabric-to-device interface enables a device’s management information to be registered.
D 4 – Managing Switches Configuring a Switch you can no longer communicate with that switch by means other than a direct Ethernet or serial connection. 4.9.2.7 FC-SW-2 Compliance for Zoning When a zone set is activated, SANbox2 switches and other FC-SW-2 compliant switches propagate the active zone set to all switches in the fabric. Some non-FC-SW-2 compliant switches propagate not only the active zone set, but the entire zoning database.
D 4 – Managing Switches Configuring a Switch Table 4-7. Timeout Values Parameter Description R_A_TOV Resource Allocation Timeout: Represents the maximum time a frame could be delayed in the Fabric and still be delivered. The default is 10000 milliseconds. E_D_TOV Error Detect Timeout: Represents the maximum round trip time that an operation between two N_Ports could require. The default is 2000 milliseconds. 4.9.
D 4 – Managing Switches Configuring a Switch 4.9.3.1 IP Configuration The IP configuration identifies the switch on the Ethernet network and determines which network discovery method to use. Table 4-8 describes the IP configuration parameters. Table 4-8. IP Configuration Parameters Parameter 59048-04 Rev. B Description Network Discovery Choose one of the following methods by which to assign the IP address: Static - Uses the IP configuration parameters entered in the Switch Properties dialog.
D 4 – Managing Switches Configuring a Switch 4.9.3.2 SNMP Configuration The SNMP configuration defines how authentication traps are managed.Table 4-9 describes the SNMP configuration parameters. The illegal characters for the user-defined fields are the pound sign (#), semi-colon (;), and comma (,). Table 4-9. SNMP Configuration Parameters 4-28 Parameter Description SNMP Enabled Enables or disables SNMP communication with other switches in the fabric.
D 4 – Managing Switches Configuring a Switch 4.9.3.3 SNMP Trap Configuration The SNMP trap configuration defines how traps are set. Choose from the tabs Trap1 – Trap 5 to configure each trap. Table 4-10 describes the SNMP configuration parameters. Table 4-10. SNMP Trap Configuration Parameters Parameter Description Trap Version Specifies the SNMP version (1 or 2) with which to format traps. Trap 1 Enabled Enables or disables the trap. If disabled, traps are not configurable.
D 4 – Managing Switches Archiving a Switch 4.10 Archiving a Switch You can create an .XML archive file containing the configuration parameters. Basically any data received by SANbox Manager is archived. However, user authentication and passwords are available only through the command line interface, and are not received by SANbox Manager, and thus are not archived.
D 4 – Managing Switches Restoring a Switch 2. Open the Switch menu in the faceplate display and select Restore to display the Restore dialog shown in Figure 4-13. The Restore dialog offers a Full Restore and a Selective Restore tab. Figure 4-13. Restore Dialogs – Full and Selective 3. Enter the archive file name or browse for the file. This archive file must be one that was produced by the SANbox Manager Archive function.
D 4 – Managing Switches Restoring the Factory Default Configuration Port Properties: Restores all settings presented in the Port properties dialog. Refer to ”Configuring Ports” on page 6-10. Configured Zoning: Restores all zone sets, zones, and aliases in the switch’s zoning database. 4.12 Restoring the Factory Default Configuration You can restore the switch and port configuration settings to the factory default values.
D 4 – Managing Switches Restoring the Factory Default Configuration Table 4-11. Factory Default Configuration Settings (Continued) Setting 59048-04 Rev. B Value FDMI HBA Entry Level 1000 Subnet mask address 255.0.0.0 Gateway address 10.0.0.254 Network Discovery Static Remote Logging False Remote Logging host IP address 10.0.0.254 Contact Undefined Location Undefined Trap enabled False Trap Port 162 Trap Address Trap 1: 10.0.0.254; Traps 2-5: 0.0.0.
D 4 – Managing Switches Managing Firmware 4.13 Managing Firmware The switch memory is partitioned for two firmware images. One of these partitions contains the active firmware; that is, the firmware version that is in use. The other partition contains the inactive firmware which is not in use. The pending firmware is the firmware that will be activated at the next switch reset. The pending firmware can be the active firmware or the inactive firmware.
D 4 – Managing Switches Managing Firmware After an NDCLA operation is complete, management connections must be re-initiated: SANbox Manager sessions will re-connect automatically Telnet sessions must be restarted manually. Applicable Code Versions: Future switch code releases will be upgraded non-disruptively unless specifically indicated in its associated release notes An NDCLA operation to previous switch code releases is not supported. To install firmware, do the following: 1.
D 4 – Managing Switches Managing Firmware 4.13.4 Displaying Hardware Status A switch is equipped with the following chassis LEDs that provide hardware status information: Chassis Over Temperature LED - indicates the temperature status of the switch. Fan Fail LED - indicates operational status of both fans. Heartbeat LED - indicates the status of the internal switch processor and the results of the power-on self test (POST). Input Power LED - indicates the voltage status of the switch.
Section 5 Managing I/O Blades An I/O blade is a component switch of the larger SANbox2-64 switch. When you configure an I/O blade and its ports you are really configuring the slot. Because this configuration is saved on the switch CPU, any I/O blade that you install in that slot will acquire that configuration.
D 5 – Managing I/O Blades Changing the I/O Blade Administrative State 5.2 Changing the I/O Blade Administrative State The I/O blade administrative state determines the operational status of the I/O blade and its ports. The I/O blade administrative state exists in two forms: the configured administrative state and the current administrative state. The configured administrative state is the state that is saved in the switch configuration and is preserved across switch resets.
D 5 – Managing I/O Blades Resetting an I/O Blade 5.4 Resetting an I/O Blade Resetting an I/O blade reinitializes the I/O blade using the saved configuration. To reset an I/O blade, do the following: 1. Select one or more blades in the faceplate display. 2. Open the Blade menu and select Reset Blade. 5.5 Hot Swap Wizard The Hot Swap Wizard is a series of dialogs that walk you through the process of replacing, removing, or inserting an I/O blade while the switch is running.
D 5 – Managing I/O Blades Hot Swap Wizard 5-4 Removing an I/O Blade 1. Select the Remove a Blade hot swap procedure 2. Select and confirm the slot from which to remove the blade. 3. The Port Status LEDs will flash green to positively identify the I/O blade. Remove the I/O blade and confirm. 59048-04 Rev.
Section 6 Managing Ports This section describes the following tasks that manage ports and devices: Displaying port information Configuring ports Testing ports 6.1 Displaying Port Information Port information is available primarily in the faceplate display shown in Figure 6-1. The faceplate display data windows provide information and statistics for switches and ports. Use the topology display to view status information on fabrics, switches, and links between switches. Figure 6-1.
D 6 – Managing Ports Displaying Port Information 6.1.1 Monitoring Port Status The faceplate display provides the following port related information: Port type Port operational state Port speed Port media To display port number and status information for a port, position the cursor over a port on the faceplate display. The status information changes depending on the View menu option selected. 6.1.1.
D 6 – Managing Ports Displaying Port Information 6.1.1.2 Displaying Port Operational States To display the operational state on each port in the faceplate display, open the View menu and select View Port States. Table 6-2 lists the possible operational states and their meanings. The port operational state refers to actual port state and not the administrative state you may have assigned. Table 6-2. Port Operational States State Description On Online – port is active and ready to send data.
D 6 – Managing Ports Displaying Port Information 6.1.1.4 Displaying Transceiver Media Status To display transceiver media status, open the View menu and select View Port Media. Table 6-4 lists the port media states and their meanings. Table 6-4. Transceiver Media View Media Icon Description Optical SFP (Green), logged-in, active, and ready to send data.
D 6 – Managing Ports Displaying Port Information Table 6-5. Port Statistics Data Window Entries Entry 59048-04 Rev. B Description Start Time The beginning of the period over which the statistics apply. The start time for the Absolute view is not applicable. The start time for the Rate view is the beginning of polling interval. The start time for the Baseline view is the last time the baseline was set. End Time The last time the statistics were updated on the display.
D 6 – Managing Ports Displaying Port Information Table 6-5. Port Statistics Data Window Entries (Continued) Entry 6-6 Description Flow Errors Number of times a frame is received and all the switch ports receive buffers are full. The normal Fabric Login exchange of flow control credit should prevent this from occurring. The frame will be discarded. FReject Number of frames, from devices, that have been rejected. Frames can be rejected for any of a large number of reasons.
D 6 – Managing Ports Displaying Port Information Table 6-5. Port Statistics Data Window Entries (Continued) Entry Description Total Errors Total number of primitive and non-primitive port link errors. Total Link Resets Number of link-reset primitives the transmitted by the port. Total LIPs Received Number of loop initialization primitive frames received. Total LIPs Transmitted Number of loop initialization primitive frames transmitted.
D 6 – Managing Ports Displaying Port Information Table 6-6. Port Information Data Window Entries (Continued) Entry 6-8 Description Administrative Port State The port state (Online, Offline, Diagnostics, or Down) which has been set by the user. This state may be different from the configured administrative state if the user has not saved it in the switch configuration. This state is used at the time it is set to try to set the port operational state.
D 6 – Managing Ports Displaying Port Information Table 6-6. Port Information Data Window Entries (Continued) Entry Description Ext Credits Requested Whether extended credits have been requested for ports. Credits to Donate The number of credits available to be donated by the selected port. Donor Group The donor group of the selected port. Valid Donor Groups The number of separate groups within which extended credits may be donated and assigned. Medium The transceiver type. 6.1.
D 6 – Managing Ports Configuring Ports 6.2 Configuring Ports The port settings or characteristics are configured using the Port Properties dialog shown in Figure 6-2. To open the Port Properties dialog, select one or more ports, open the Port menu and select Port Properties. Figure 6-2. Port Properties Dialog The Port Properties dialog displays the switch name and the selected port(s).
D 6 – Managing Ports Configuring Ports 6.2.1 Changing Port Administrative States The port administrative state determines the operational state of a port. The port administrative state exists in two forms: the configured administrative state and the current administrative state. The configured administrative state is the state that is saved in the switch configuration and is preserved across switch resets. SANbox Manager always makes changes to the configured administrative state.
D 6 – Managing Ports Configuring Ports 6.2.2 Changing Port Speeds Ports are capable of transmitting and receiving at 1 or 2 Gbps. The ports can be configured for either transmission speed or to sense the transmission speed of the device to which it is connected. Table 6-8 describes the port speeds. To change the port speed, do the following: 1. Select one or more ports in the faceplate display. 2. Open the Port menu and select Port Properties. 3.
D 6 – Managing Ports Configuring Ports Table 6-9. Port Types (Continued) State Description GL_Port Generic loop port - Self discovers as an F_Port, FL_Port, or an E_Port. GL_Port is the default port type. A single device on a public loop will attempt to configure as an F_Port first, then if that fails, as an FL_Port. Donor Donor port - Allows buffer credits to be used by another port. 6.2.
D 6 – Managing Ports Configuring Ports 6.2.5 Changing Port Symbolic Name To change the symbolic name of a port from the faceplate display, do the following: 1. Open the faceplate display and select a port. 2. Open the Port menu and select Port Symbolic Name. 3. In the Port Symbolic Name dialog, choose one of the following: 4. Enter a new name for the port in the Set Port Symbolic Name field. Check the Restore Default Port Symbolic Name check box to restore the default name.
D 6 – Managing Ports Configuring Ports 1. Extended Distance on SANbox2: Explains the concepts and principles of extending port credits. Click the Next button. 2. Extended Distance Requirements: Specify speed and distance requirements for each port then click the Next button. 3. Designate Donor Ports: Select available ports and click >> to move the port into the Selected Donor Port column shown in Figure 6-3. Match the number of ports needed with the number of designated donor ports.
D 6 – Managing Ports Resetting a Port 6.3 Resetting a Port The Reset Port option reinitializes the port using the saved configuration. To reset a port, do the following: 1. In the faceplate display, select the ports to be reset. 2. Open the Port menu and select Reset Port. 6.4 Testing Ports The port loopback tests verify correct port operation by sending a frame out through the loop, and then verifying that the frame received matches the frame that was sent.
D 6 – Managing Ports Testing Ports to the ASIC for the selected ports. The port passes the test if the test frame that was sent by the ASIC matches the test frame that was received. This test requires that the port be in diagnostics mode, and therefore, disrupts communication. Node-to-Node (Online) - The Node-to-Node test verifies communications between the port and its device node or device loop. The port being tested must be online and connected to a remote device.
6 – Managing Ports Testing Ports D Notes 6-18 59048-04 Rev.
Appendix A Command Line Interface The command line interface (CLI) enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection. This section describes the following: Logging on to a switch User accounts Working with switch configurations Commands A.
A – Command Line Interface Working with Switch Configurations Note: D A switch supports a combined maximum of 19 logins or sessions reserved as follows: 4 logins or sessions for internal applications such as management server and SNMP 9 high priority Telnet sessions 6 logins or sessions for SANbox Manager inband and out-of-band logins, Application Programming Interface (API) inband and out-of-band logins, and Telnet logins. Additional logins will be refused. A.
D A – Command Line Interface Working with Switch Configurations Set Config commands with which you make modifications to the port, switch, port threshold alarm, or zoning configuration components as shown: SANbox2 #> admin start SANbox2 (admin) #> config edit default The config named default is being edited. SANbox2 (admin-config)#> set config port . . . SANbox2 (admin-config)#> set config switch . . . SANbox2 (admin-config)#> set config threshold . . . SANbox2 (admin-config)#> set config zoning . . .
A – Command Line Interface Working with Switch Configurations D You use FTP to download the configdata file to your workstation for safe keeping and to upload the file back to the switch for the restore function. To download the configdata file, open an FTP session on the switch and login with the account name images and password images. Transfer the file in binary mode with the Get command as shown: >ftp ip_address user:images password: images ftp>bin ftp>get configdata xxxxx bytes sent in xx secs.
D A – Command Line Interface Commands A.4 Commands The command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The Command is followed by one or more keywords. Consider the following rules and conventions: Commands and keywords are case insensitive. Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value]. Underlined portions of the keyword in the command format indicate the abbreviated form that can be used.
D A – Command Line Interface Commands The command set performs monitoring and configuration tasks. Commands related to monitoring tasks are available to all account names. Commands related to configuration tasks are available only within an admin session. An account must have Admin authority to enter the Admin Start command, which opens an admin session. Refer to the ”Admin Command” on page A-7. The commands and their page numbers are listed in Table A-2. Table A-2.
D A – Command Line Interface Admin Command Admin Command Opens and closes an Admin session. The Admin session provides commands that change the fabric and switch configurations. Only one Admin session can be open on the switch at any time. An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command. Refer to the ”Set Setup Command” on page A-49.
D A – Command Line Interface Alias Command Alias Command Creates a named set of ports/devices. Aliases make it easier to assign a set of ports/devices to many zones. An alias can not have a zone or another alias as a member.
D A – Command Line Interface Alias Command members [alias] Displays all members of the alias given by [alias]. This keyword does not require an admin session. remove [alias] [member_list] Removes the ports/devices given by [member_list] from the alias given by [alias]. Use a to delimit ports/devices in [member_list]. A port/device in [member_list] can have any of the following formats: Domain ID and port number pair (Domain ID, Port Number). Domain IDs can be 1–-239; port numbers can be 0–-255.
A – Command Line Interface Config Command D Config Command Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, refer to the ”Set Config Command” on page A-34.
D A – Command Line Interface Config Command restore Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, then enter the Config Restore command. After the restore is complete, the switch automatically resets. Refer to ”Backing up and Restoring Switch Configurations” on page A-3.
A – Command Line Interface Config Command D The following is an example of how to create a backup file (configdata) and download the file to the workstation.
D A – Command Line Interface Date Command Date Command This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Authority Admin session except to display the date. Syntax date [MMDDhhmmCCYY] Keywords [MMDDhhmmCCYY] Specifies the date – this requires an admin session.
D A – Command Line Interface Fallback Command Fallback Command Assigns the pending firmware status back and forth between the active and inactive firmware images stored in switch memory. Authority Admin session Syntax Notes fallback Examples The Show Switch command displays the two firmware images, active firmware, inactive firmware, and pending firmware versions. After executing the Fallback command, reset the switch to activate the pending firmware.
D A – Command Line Interface Hardreset Command Hardreset Command Resets the switch and performs a power-on self test. This reset disrupts traffic, activates the pending firmware, and clears the alarm log. To save the alarm log before resetting, refer to the ”Set Log Command” on page A-44. Authority Admin session Syntax Notes hardreset To reset the switch without a power-on self test, refer to the ”Reset Command” on page A-27.
D A – Command Line Interface Help Command Help Command Displays a brief description of the specified command, its keywords, and usage. Authority None Syntax Keywords help [command] [keyword] [command] Displays a summary of the command given by [command] and its keywords. If you omit [command], the system displays all available commands. [keyword] Displays a summary of the keyword given by [keyword] belonging to the command given by [command].
D A – Command Line Interface History Command History Command Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority None Syntax Notes history Examples Use the History command to provide context for the ! command: Enter ![command] to re-enter the most recent execution of that command.
A – Command Line Interface Hotreset Command D Hotreset Command Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This command terminates all management sessions, saves all configuration information, and clears the alarm log. After the pending firmware is activated, the configuration is recovered. This process takes less than 80 seconds. To save the alarm log to a file before resetting, refer to the ”Set Log Command” on page A-44.
D A – Command Line Interface Hotswap Command Hotswap Command This command prompts you step-by-step through the procedure to replace an I/O blade, insert an I/O blade, or remove an I/O blade while the switch is running. Authority Admin session Syntax Notes hotswap The Hotswap command automatically starts and ends an Admin session in the presence of admin authority. Always perform the hot swap procedure as prompted, otherwise the switch will become unresponsive.
D A – Command Line Interface Hotswap Command to replace? (1,2,3,4,6,7,8,9): [1] 6 o Remove all connections from the IO blade in slot 6. o Remove the IO blade in slot 6 from the chassis. Have the above operations been completed? (y = proceed / n = cancel) y Hotswap IO blade removal sub-procedure successfully completed. If you wish to continue with the replacement procedure please note that after the blade has been successfully inserted: o Diagnostics will be performed on the IO blade.
D A – Command Line Interface Image Command Image Command Manages and installs switch firmware. Authority Admin session Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] list unpack [file] Keywords cleanup Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.
A – Command Line Interface Lip Command D Lip Command Reinitializes the specified loop port. Authority Admin session Syntax Keywords lip [port_number] Examples The following is an example of the Lip command: [port_number] The number of the port to be reinitialized. SANbox2 (admin) #> lip 2 A-22 59048-04 Rev.
D A – Command Line Interface Passwd Command Passwd Command Changes a user account’s password. Authority Admin account name and an admin session to change another account’s password; You can change you own password without an Admin session. Syntax Keywords passwd [account_name] Examples The following is an example of the Passwd command: [account_name] The user account name. To change the password for an account name other than your own, you must open an admin session with the account name Admin.
A – Command Line Interface Ping Command D Ping Command Initiates an attempt to communicate with another switch over an Ethernet network and reports the result. Authority None Syntax ping ip_address Keywords ip_address The IP address of the switch to query. Examples The following is an example of a successful Ping command: SANbox2 #> ping 10.20.11.57 Ping command issued. Waiting for response... SANbox2 #> Response successfully received from 10.20.11.57.
D A – Command Line Interface Ps Command Ps Command Displays current system process information. Authority None Syntax Examples ps The following is an example of the Ps command: SANbox2 #> ps PID PPID %CPU TIME ELAPSED COMMAND 338 327 0.0 00:00:00 3-01:18:35 cns 339 327 0.0 00:00:01 3-01:18:35 ens 340 327 0.0 00:00:21 3-01:18:35 dlog 341 327 0.1 00:05:35 3-01:18:35 ds 342 327 0.2 00:11:29 3-01:18:35 mgmtApp 343 327 0.0 00:00:04 3-01:18:35 fc2 344 327 0.
A – Command Line Interface Quit Command D Quit Command Closes the Telnet session. Authority None Syntax Notes quit, exit, or logout A-26 You can also enter Control-D to close the Telnet session. 59048-04 Rev.
D A – Command Line Interface Reset Command Reset Command Resets the switch configuration parameters. If you omit the keyword, the default is Reset Switch. Authority Admin session Syntax reset blade [slot_number] config [config_name] factory port [port_number] snmp switch (default) system zoning Keywords blade [slot_number] Resets the I/O or cross-connect blade that occupies the slot given by [slot_number]. I/O blade slot numbers are 1–4 and 6–9; cross-connect slot numbers are 11–12.
D A – Command Line Interface Reset Command switch Resets the switch without a power-on self test. This is the default. This reset disrupts traffic and does the following: Activates the pending firmware. Closes all management sessions. Clears the alarm log. To save the alarm log before resetting, refer to the ”Set Log Command” on page A-44. To reset the switch with a power-on self test, refer to the ”Hardreset Command” on page A-15.
D A – Command Line Interface Reset Command Table A-3. Switch Configuration Defaults Parameter Default Principal Priority 254 Configuration Description SANbox2-64 FC Switch Table A-4. Port Configuration Defaults Parameter 59048-04 Rev.
D A – Command Line Interface Reset Command Table A-5.
D A – Command Line Interface Reset Command Table A-7. SNMP Configuration Defaults Parameter Default SNMPEnabled True Contact Location Description SANbox2-64 FC Switch Trap [1-5] Address Trap 1: 10.0.0.254; Traps 2–5: 0.0.0.0 Trap [1-5] Port 162 Trap [1-5] Severity Warning Trap [1-5] Version 2 Trap [1-5] Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.12 AuthFailureTrap False ProxyEnabled True Table A-8.
A – Command Line Interface Set Command D Set Command Sets a variety of switch parameters. Authority Admin session for all keywords except Beacon and Pagebreak which are available without an Admin session. Syntax set alarm clear beacon [state] blade [slot_number] [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state] Keywords alarm clear Clears the alarm log. beacon [state] Enables or disables the flashing of the Port Status LEDs according to [state].
D A – Command Line Interface Set Command log [option] Specifies the type of entries to be entered in the event log. Refer to the ”Set Log Command” on page A-44. pagebreak [state] Specifies how much information is displayed on the screen at a time according to the value given by [state]. This keyword does not require an admin session. [state] can be one of the following: on Limits the display of information to 20 lines at a time.
A – Command Line Interface Set Config Command D Set Config Command Sets switch, blade, port, port threshold alarm, and zoning configuration parameters. The changes you make with this command are not retained when you reset or power cycle the switch unless you save them using the Config Save command. Refer to the ”Config Command” on page A-10.
D A – Command Line Interface Set Config Command Table A-9. Set Config Port Parameters Parameter AdminState Description Port administrative state: Online – Activates and prepares the port to send data. This is the default. Offline – Prevents the port from receiving signal and accepting a device login. Diagnostics – Prepares the port for testing and prevents the port from accepting a device login. Down – Disables the port by removing power from the port lasers. 59048-04 Rev.
D A – Command Line Interface Set Config Command Table A-9. Set Config Port Parameters (Continued) Parameter A-36 Description ExtCredit Extended credits. The number of port buffer credits that this port can acquire from donor ports. The default is 0. FANEnable Fabric address notification. Enables (True) or disables (False) the communication of the FL_Port address, port name, and node name to the logged-in NL_Port. The default is True. LCFEnable Link control frame preference routing.
D A – Command Line Interface Set Config Command switch Initiates an editing session in which to change switch configuration settings. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table A-10 describes the Set Config Switch parameters. Table A-10. Set Config Switch Parameters Parameter 59048-04 Rev.
D A – Command Line Interface Set Config Command Table A-10. Set Config Switch Parameters (Continued) Parameter Description E_D_TOV Error Detect Timeout Value. The number of milliseconds a port is to wait for errors to clear. The default is 2000. PrincipalPriority The priority used in the FC-SW-2 principal switch selection algorithm. 1 is high, 255 is low. The default is 254. ConfigDescription Switch configuration description.
D A – Command Line Interface Set Config Command Table A-11. Set Config Threshold Parameters Parameter Description Threshold Monitoring Enabled Master enable/disable parameter for all events. Enables (True) or disables (False) the generation of all enabled event alarms. The default is False. CRCErrorsMonitoringEnabled DecodeErrorsMonitoringEnabled ISLMonitoringEnabled LoginMonitoringEnabled LogoutMonitoringEnabled LOSMonitoringEnabled The event type enable/disable parameter.
D A – Command Line Interface Set Config Command Table A-12. Set Config Zoning Parameters Parameter Examples Description FC-SW-2 AutoSave Available only when the FC-SW-2 Compliant parameter is True, this parameter enables (True) or disables (False) the saving of changes to active zone set in the switch’s permanent memory. Refer to ”FC-SW-2 Compliant” on page A-38. The default is True.
D A – Command Line Interface Set Config Command press 'q' or 'Q' and the ENTER key to do so.
D A – Command Line Interface Set Config Command FDMIEnabled (True / False) [True ] FDMIEntries (decimal value, 0-1000) [1000 ] DefaultDomainID (decimal value, 1-239) [11 ] DomainIDLock (True / False) [True ] SymbolicName (string, max=32 chars) [SANbox2 R_A_TOV (decimal value, 100-100000 msec) [10000 ] E_D_TOV (decimal value, 10-20000 msec) [2000 ] PrincipalPriority (decimal value, 1-255) [254 ] ConfigDescription (string, max=32 chars) [SANbox2-64 FC Switch] FC-SW-2 Compli
D A – Command Line Interface Set Config Command LogoutMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [5 ] FallingTrigger (decimal value, 0-1000) [1 ] SampleWindow (decimal value, 1-1000 sec) [10 ] (True / False) [True ] RisingTrigger (decimal value, 1-1000) [100 ] FallingTrigger (decimal value, 0-1000) [5 ] SampleWindow (decimal value, 1-1000 sec) [10 ] LOSMonitoringEnabled Finished configuring attributes.
A – Command Line Interface Set Log Command D Set Log Command Specifies the type of entries to be entered in the event log. Log entries are created for ports, components, and event severity levels.
D A – Command Line Interface Set Log Command Other Monitors other miscellaneous events. Port Monitors all port events Switch Monitors switch management events. Zoning Monitors zoning conflict events. level [level] Specifies the severity level given by [level] to use in monitoring events for the specified components or ports. [level] can be one of the following values: Critical Monitors critical events. Warn Monitors warning events. Info Monitors informational events.
A – Command Line Interface Set Log Command D start Starts the logging of events based on the Port, Component, and Level keywords assigned to the current configuration. The logging continues until you enter the Set Log Stop command. stop Stops logging of events. Notes A-46 To maintain optimal switch performance, do not set the Component keyword to All and the Level keyword to Info at the same time. 59048-04 Rev.
D A – Command Line Interface Set Port Command Set Port Command Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin session except for the Clear keyword. Syntax set port [port_number] bypass [alpa] clear enable speed [transmission_speed] state [state] Keywords [port_number] Specifies the port. Ports are numbered beginning with 0.
A – Command Line Interface Set Port Command D Down Disables the port by removing power from the port lasers. A-48 59048-04 Rev.
D A – Command Line Interface Set Setup Command Set Setup Command Changes SNMP and system configuration settings. The switch maintains one SNMP configuration and one system configuration. Authority Admin session Syntax set setup snmp system Keywords snmp Prompts you in a line-by-line fashion to change SNMP configuration settings. Table A-13 describes the SNMP fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table A-13.
D A – Command Line Interface Set Setup Command Table A-13. SNMP Configuration Settings (Continued) Entry Description ReadCommunity Read community password that authorizes an SNMP agent to read information from the switch. This is a write-only field. The value on the switch and the SNMP management server must be the same. The read community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is “public”.
D A – Command Line Interface Set Setup Command Table A-14. System Configuration Settings (Continued) Entry Examples Description Eth0NetworkMask Ethernet subnet mask address. Eth0GatewayAddress Ethernet IP address gateway. AdminTimeout Specifies the amount of time in minutes the switch waits before terminating an idle Admin session. Zero (0) disables the time out threshold. The default is 30, the maximum is 1440.
D A – Command Line Interface Set Setup Command Trap1Enabled (True / False) [False ] Trap2Address (dot-notated IP Address) [0.0.0.0 ] Trap2Port (decimal value) [162 ] Trap2Severity (see allowed options above) [warning ] Trap2Version (1 / 2) [2 ] Trap2Enabled (True / False) [False ] Trap3Address (dot-notated IP Address) [0.0.0.
D A – Command Line Interface Show Command Show Command Displays fabric, switch, and port operational information.
D A – Command Line Interface Show Command chassis Displays chassis component status and temperature. config [option] Displays switch, port, and zoning configuration attributes. Refer to the ”Show Config Command” on page A-67. domains Displays list of each domain and its worldwide name in the fabric. donor Displays list of current donor configuration for all ports. fabric Displays list of each domain, symbolic name, worldwide name, node IP address, and port IP address.
D A – Command Line Interface Show Command [domain_id] Displays name server information for the switch given by [domain_id]. [domain_id] is a switch domain ID. [port_id] Displays name server information for the port given by [port_id]. [port_id] is a port Fibre Channel address. pagebreak Displays the current pagebreak setting. The pagebreak setting limits the display of information to 20 lines (On) or allows the continuous display of information without a break (Off).
D A – Command Line Interface Show Command Table A-15. Show Port Parameters (Continued) Entry A-56 Description FBusy Number of times the switch sent a F_BSY because Class 2 frame could not be delivered within ED_TOV time. Number of class 2 and class 3 fabric busy (F_BSY) frames generated by this port in response to incoming frames. This usually indicates a busy condition on the fabric or N_Port that is preventing delivery of this frame.
D A – Command Line Interface Show Command Table A-15. Show Port Parameters (Continued) Entry Description RxLinkResets Number of link reset primitives received from an attached device. RxOfflineSeq Number of offline sequences received. An OLS is issued for link initialization, a Receive & Recognize Not_Operational (NOS) state, or to enter the offline state. TotalErrors Total number of errors detected. TotalLIPsRecvd Number of loop initialization primitive frames received by this port.
D A – Command Line Interface Show Command support Executes a series of commands that display a complete description of the switch, its configuration, and operation. The display can be captured from the screen and used for diagnosing problems. This keyword is intended for use at the request of your authorized maintenance provider.
D A – Command Line Interface Show Command IO-4 6 32-39 Online Online Compromised Normal 0 IO-5 7 40-47 Online Online Passed Normal 0 IO-6 8 48-55 Online NotInstalled NotInstalled Normal 0 IO-7 9 56-63 Online NotInstalled NotInstalled Normal 0 CC-0 11 * Online Online Passed Normal * CC-1 12 * Online Online Passed Normal * The following is an example of the Show Chassis command: SANbox2 #> show chassis Chassis Information ------------------FanStatus (1) Good FanStat
D A – Command Line Interface Show Command Domain 100 (0x64) WWN = 10:00:00:c0:dd:00:ba:68 Domain 101 (0x65) WWN = 10:00:00:60:df:22:2e:06 Domain 102 (0x66) WWN = 10:00:00:c0:dd:00:90:ef Domain 103 (0x67) WWN = 10:00:00:60:69:50:0b:6c Domain 104 (0x68) WWN = 10:00:00:c0:dd:00:b8:b7 The following is an example of the Show Fabric command: SANbox2 #> show fabric Domain WWN Enet IP Addr FC IP Addr SymbolicName ------ --- ------------ ---------- ------------ 16 (0x10) 10:00:00:c0:dd:00:77:8
D A – Command Line Interface Show Command The following is an example of the Show FDMI WWN command: SANbox2 #> show fdmi 21:00:00:e0:8b:09:3b:17 FDMI Information ----------------Manufacturer QLogic Corporation SerialNumber 95923 Model QCP2340 ModelDescription NodeWWN 20:00:00:e0:8b:09:3b:17 HardwareVersion A DriverVersion 4.12 Beta 21 OptionRomVersion FirmwareVersion 3.2.15 OSSystemName SunOS 5.
D A – Command Line Interface Show Command The following is an example of the Show NS [port_ID] command: SANbox2 #> show ns 1301e1 Port ID: 1301e1 -------PortType NL PortWWN 21:00:00:20:37:73:13:69 SymbolicPortName NodeWWN 20:00:00:20:37:73:13:69 SymbolicNodeName NodeIPAddress 0.0.0.0 ClassOfService 3 PortIPAddress 0.0.0.
D A – Command Line Interface Show Command DiagStatus Passed SFPRevision 0 EpConnState None SFPType NotInstalled EpIsoReason NotApplicable SFPVendor Unknown LinkSpeed 2Gb/s SFPVendorID 00000000 LinkState Inactive SymbolicName Port1 LoginStatus NotLoggedIn SyncStatus SyncLost MaxCredit 12 XmitterEnabled True OperationalState Offline ALInit 0 LIP_F8_AL_PS 0 ALInitError 0 LIP_F8_F7 0 BadFrames 0 LinkFailures 26 Class2FramesIn 0 Login 25 Class2FramesOut 0 Logout 24
D A – Command Line Interface Show Command 5 CPU-0 Passed Normal * 6 IO-4 32-39 Good * Good Compromised Normal 0 7 IO-5 40-47 Good Passed Normal 0 8 IO-6 - NotInstalled NotInstalled Normal 0 9 IO-7 - NotInstalled NotInstalled Normal 0 10 PS-1 * NotInstalled Passed Normal * 11 CC-0 * Good Passed Normal * 12 CC-1 * Good Passed Normal * The following is an example of the Show Switch command: SANbox2 #> show switch Switch Information -----------------SymbolicN
D A – Command Line Interface Show Command Number Type PortWWN ------ ----- ------- Type NodeWWN ID ------ ------- ------ 5 F 20:05:00:c0:dd:00:bd:ec N 20:00:00:00:c9:22:1e:93 010500 P 10 E 20:0a:00:c0:dd:00:bd:ec E 10:00:00:c0:dd:00:80:21 4(0x4) D The following is an example of the Show Topology command for port 1: SANbox2 #> show topology 1 Local Link Information ---------------------PortNumber 1 PortID 650100 PortWWN 20:01:00:c0:dd:00:91:11 PortType F Remote Link Information
D A – Command Line Interface Show Command The following is an example of the Show Version command: SANbox2 #> show version ***************************************************** * * * Command Line Interface SHell (CLISH) * * * ***************************************************** SystemDescription SANbox2-64 FC Switch Eth0NetworkAddress 10.20.11.
D A – Command Line Interface Show Config Command Show Config Command Displays switch, I/O blade, port, alarm threshold, and zoning for the current configuration. Authority None Syntax show config blade [slot_number] port [port_number] switch threshold zoning Keywords blade [slot_number] Displays configuration parameters for the I/O blade or cross-connect blade that occupies the slot given by [slot_number].
D A – Command Line Interface Show Config Command MSEnabled True NoClose False IOStreamGuard Disabled VIEnabled False PDISCPingEnable True The following is an example of the Show Config Switch command: SANbox2 #> show config switch Configuration Name: default ------------------Switch Configuration Information -------------------------------AdminState Online BroadcastEnabled False InbandEnabled True FDMIEnabled False FDMIEntries 10 DomainID 19 (0x13) DomainIDLock True SymbolicName s
D A – Command Line Interface Show Config Command DecodeErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 0 SampleWindow 10 ISLMonitoringEnabled True RisingTrigger 2 FallingTrigger 0 SampleWindow 10 LoginMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LogoutMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LOSMonitoringEnabled True RisingTrigger 100 FallingTrigger 5 SampleWindow 10 The following is an example of
A – Command Line Interface Show Log Command D Show Log Command Displays the contents of the log or the parameters used to create entries in the log. The log contains a maximum of 200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest. Authority None Syntax show log component level options port settings Keywords component Displays the components currently being monitored for events.
D A – Command Line Interface Show Log Command level Displays the event severity level needed to create an entry in the log. If the severity level occurs on a port or on a component which is not defined, no entry is made in the log. The severity levels are as follows: Critical Monitors critical events. Warn Monitors warning events. Info Monitors informational events. None Monitors none of the severity levels. options Displays the options used to set the component and severity level attributes.
A – Command Line Interface Show Log Command D The following is an example of the Show Log command: SANbox2 #> show log [327][day month date time year][I][Eport Port:0/8][Eport State= E_A0_GET_DOMAIN_ID] [328][day month date time year][I][Eport Port: 0/8][FSPF PortUp state=0] [329][day month date time year][I][Eport Port: 0/8][Sending init hello] [330][day month date time year][I][Eport Port: 0/8][Processing EFP, oxid= 0x8] [331][day month date time year][I][Eport Port: 0/8][Eport State = E_A2_IDLE] [332][
D A – Command Line Interface Show Perf Command Show Perf Command Displays port performance in frames/second and bytes/second. If you omit the keyword, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames/second and bytes per second.
D A – Command Line Interface Show Perf Command errors [port_number] Displays continuous error counts for the set of 16 ports (0–15, 16–31, ...) that include [port_number]. If you omit [port_number], ports 0–15 are displayed. Type “q” and press the Enter key to stop the display.
D A – Command Line Interface Show Setup Command Show Setup Command Displays the current SNMP and system settings. Authority None Syntax show setup mfg snmp system Keywords mfg Displays manufacturing information about the switch. snmp Displays the current SNMP settings. system Displays the current system settings.
D A – Command Line Interface Show Setup Command SNMP Information ---------------- A-76 SNMPEnabled True Contact Location N_107 System Test Lab Description SANbox2-64 FC Switch Trap1Address 10.0.0.254 Trap1Port 162 Trap1Severity warning Trap1Version 2 Trap1Enabled False Trap2Address 0.0.0.0 Trap2Port 162 Trap2Severity warning Trap2Version 2 Trap2Enabled False Trap3Address 0.0.0.
D A – Command Line Interface Show Setup Command The following is an example of the Show Setup System command: SANbox2 #> show setup system System Information ------------------ 59048-04 Rev. B Eth0NetworkDiscovery Static Eth0NetworkAddress 10.20.11.32 Eth0NetworkMask 255.255.252.0 Eth0GatewayAddress 10.20.8.254 AdminTimeout 30 UserAuthentication False LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10.0.0.
D A – Command Line Interface Shutdown Command Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command. Authority Admin session Syntax Notes shutdown Always use this command to perform an orderly shut down before removing power from the switch. When the shutdown is complete, the Heartbeat LED is extinguished. A-78 59048-04 Rev.
D A – Command Line Interface Test Command Test Command Tests I/O blades and ports using internal (SerDes level), external (transceiver), and online loopback tests. Internal and external tests require that the port be placed in diagnostic mode. Refer to the ”Set Command” on page A-32 for information about changing the I/O blade or port administrative state. While the test is running, the remaining ports on the switch remain fully operational.
D A – Command Line Interface Test Command 2. Place the port in Diagnostics mode, enter the following command (x = port number) and press the Enter key. set port x state diagnostics 3. Choose the type of port loopback test to run: To run an internal loopback test, enter the following: test port x internal To run an external loopback test, enter the following command. A loopback plug must be installed for this test to pass. test port x external 4.
D A – Command Line Interface Test Command 3. A series of test parameters are displayed on the screen. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize (256 byte maximum in some cases) parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload.
D A – Command Line Interface Uptime Command Uptime Command Displays the elapsed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activation does not reset the elapsed up time reported by this command. Authority None Syntax Examples uptime The following is an example of the Uptime command: SANbox2 #> uptime Elapsed up time : 0 day(s), 2 hour(s), 28 min(s), 44 sec(s) Reason last reset: NormalReset A-82 59048-04 Rev.
D A – Command Line Interface User Command User Command Administers and displays user accounts. Authority Admin account name and an Admin session. The Accounts and List keywords are available to all account names without an Admin session. Syntax user accounts add delete [account_name] edit list Keywords accounts Displays all user accounts that exist on the switch. This keyword is available to all account names without an Admin session. add Add a user account to the switch.
D A – Command Line Interface User Command Examples The following is an example of the User Accounts command: SANbox2 (admin) #> user accounts Current list of user accounts ----------------------------images (admin authority = False, never expires) admin (admin authority = True , never expires) chuckca (admin authority = False, expires in < 50 days) gregj (admin authority = True , expires in < 100 days) fred (admin authority = True , never expires) The following is an example of the User Add com
D A – Command Line Interface User Command The following is an example of the User Delete command: SANbox2 (admin) #> user del user3 The user account will be deleted. Please confirm (y/n): [n] y The following is an example of the User List command: SANbox2 (admin) #> user list 59048-04 Rev. B User Ethernet Addr-Port Logged in Since ---- ------------------ --------------- admin@OB-session1 10.20.68.108-1031 day month date time year admin@OB-session2 10.20.68.
D A – Command Line Interface Whoami Command Whoami Command Displays the account name, session number, and switch domain ID for the Telnet session. Authority None Syntax Examples whoami The following is an example of the Whoami command: SANbox2 #> whoami User name : admin@session2 Switch name : SANbox2 Switch domain ID: 21 (0x15) A-86 59048-04 Rev.
D A – Command Line Interface Zone Command Zone Command Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit session. Refer to the ”Zoning Command” on page A-93 for information about starting a Zoning Edit session. The List, Members, and Zonesets keywords are available without an Admin session.
D A – Command Line Interface Zone Command list Displays a list of all zones and the zone sets of which they are components. This keyword does not require an Admin session. members [zone] Displays all members of the zone given by [zone]. This keyword does not require an Admin session. remove [zone] [member_list] Removes the ports/devices given by [member_list] from the zone given by [zone]. Use a to delimit aliases and ports/devices in [member_list].
D Examples A – Command Line Interface Zone Command The following is an example of the Zone List command: SANbox2 #> zone list Zone ZoneSet ------------------wwn_b0241f zone_set_1 wwn_23bd31 zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402f zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command: SANbox2 #> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f ---------------
A – Command Line Interface Zone Command D The following is an example of the Zone Zonesets command: SANbox2 #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ---------------------------------zone_set_1 A-90 59048-04 Rev.
D A – Command Line Interface Zoneset Command Zoneset Command Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit session. Refer to the ”Zoning Command” on page A-93 for information about starting a Zoning Edit session. The Active, List, and Zones keywords are available without an Admin session. You must close the Zoning Edit session before using the Activate and Deactivate keywords.
D A – Command Line Interface Zoneset Command list Displays a list of all zone sets. This keyword does not require an Admin session. remove [zone_set] [zone_list] Removes a list of zones given by [zone_list] from the zone set given by [zone_set]. Use a to delimit zone names in [zone_list]. If [zone_set] is the active zone set, the zone will not be removed until the zone set has been deactivated.
D A – Command Line Interface Zoning Command Zoning Command Opens a Zoning Edit session in which to create and manage zone sets and zones. Refer to the ”Zone Command” on page A-87 and the ”Zoneset Command” on page A-91. Authority Admin session except for the Active, History, Limits, and List keywords. Syntax zoning active cancel clear edit history limits list restore save Keywords active Displays information for the active zone set including component zones and zone members.
D A – Command Line Interface Zoning Command limits Displays the number of zone sets, zones, aliases, members per zone, members per alias, and total members in the zoning database. This keyword also displays the switch zoning database limits, excluding the active zone set, which are described in Table A-16. This keyword does not require an Admin session. Table A-16.
D A – Command Line Interface Zoning Command SANbox2 (admin-zoning) #> . . SANbox2 (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
D A – Command Line Interface Zoning Command The following is an example of the Zoning List command: SANbox2 #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf
D A – Command Line Interface Zoning Command wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15: 59048-04 Rev.
A – Command Line Interface Zoning Command D Notes A-98 59048-04 Rev.
Appendix B Graphing Port Performance SANsurfer Fabric View application displays port performance using graphs. SANsurfer Fabric View plots data communication rates and total errors for selected ports as shown in Figure B-1. When graphing data communication rates, you can choose either frames/second or KB/second.
D B – Graphing Port Performance Starting SANsurfer Fabric View Save and Open SANsurfer Fabric View Default Fabric View Files Change the SANsurfer Fabric View Default Fabric File Password Set SANsurfer Fabric View preferences Set the polling frequency Display graphs Print graphs Rescale a selected graph Save graph statistics to a file B.
D B – Graphing Port Performance Exiting SANsurfer Fabric View In the Save Default Fabric View File dialog, enter an encryption key in the Default Fabric File Encryption Key field. Re-enter the encryption key in the Re-enter Encryption Key to Confirm field. Click the OK button to save the current set of SANsurfer Fabric View fabrics to the default fabric view file in the working directory.
D B – Graphing Port Performance Saving and Opening Fabric View Files B.3 Saving and Opening Fabric View Files In addition to the SANsurfer Fabric View default fabric view file, you can save and open your own fabric view files. The fabric view file contains the set of fabrics, graphs, and graphing options. To save a fabric view file, do the following: 1. Open the File menu and select Save View As to open the Save View dialog. 2.
D B – Graphing Port Performance Setting the Polling Frequency Figure B-4. Preferences – SANsurfer Fabric View B.6 Setting the Polling Frequency Fabric View updates the graphs once per second by default. To change this polling frequency, do the following: 1. Open the Graph menu, and select Set Polling Frequency to open the Set Graph Polling Frequency dialog. 2. Enter the new polling interval in seconds [1–60]. Fabric View will update the graphs once during the interval.
D B – Graphing Port Performance Displaying Graphs To remove a graph, click the graph Remove button. To remove all graphs, open the Window menu and select Close All. To remove a fabric and its graphs, select the fabric in the fabric tree, then select Remove Fabric from the Fabric menu. You can also right click on a fabric and select Remove Fabric for the popup menu. Right clicking on a graph opens a popup menu from which you can change graph options, print a graph, or save the graph statistics to a file.
D B – Graphing Port Performance Displaying Graphs Figure B-5. Default Graph Options Dialog To modify the graph options, do the following: 1. 2. Choose the units for the graph: Select the Show Bytes Data on Graph check box to plot data in KBytes/second Select the Show Frames Data on Graph check box to plot data in frames/second. Choose what data type to plot.
D B – Graphing Port Performance Printing Graphs 4. Choose the color scheme for the graph. Click a Select Color button to open its corresponding Select Color dialog, which allows you to select a new color scheme. You can select the color for each data type, the unit grid, and the background by clicking the corresponding color field or button. In each case, you can choose a color using the Swatches, Red-Green-Blue (RGB), or Hue-Saturation-Brightness (HSB) method.
D B – Graphing Port Performance Rescaling a Selected Graph B.9 Rescaling a Selected Graph The Rescale Selected Graph option auto-scales downward and re-positions the data within a graphic window to display all new data captured by the graph. To rescale a selected graph, do the following: 1. Select a displayed graph. 2. Open the Graph menu and select Rescale Selected Graph, or right-click on the graph and select Rescale from the popup menu. 3. View the data in the graph window. 4.
B – Graphing Port Performance Saving Graph Statistics to a File D Notes B-10 59048-04 Rev.
Appendix C Messages This appendix lists the SANbox Manager messages by task, dialog, or display. To find a message and what to do about it, consider what task you are performing, and refer to the corresponding subsection.
D C – Messages Add a Fabric C.2 Add a Fabric Table C-2. Add a Fabric Messages Message C-2 User Action Fabric fabricname already exists! Or Fabric name already in use. Specify a name for the fabric that is not already assigned to an existing fabric. Invalid IP Address Verify that the IP address specified is syntactically correctly. The entry switch is of a type that is not supported. The switch hardware or firmware version of the switch at the specified IP address is not supported.
D C – Messages Network Properties Dialog C.3 Network Properties Dialog Table C-3. Network Properties Dialog Messages Message 59048-04 Rev. B User Action Attempt to change snmp community strings failed. Or Attempt to change syslog configuration failed. Verify that the data is valid, that the user has permissions to modify the configuration on the switch, that the switch is reachable in the fabric, and that the fabric is reachable from the user’s workstation, then retry the configuration change.
D C – Messages Switch Properties Dialog C.4 Switch Properties Dialog Table C-4. Switch Properties Dialog Messages C-4 Message User Action Attempt to change chassis name failed Or Attempt to set ISL security failed. Or Attempt to set in-band management failed. Or Attempt to change domain ID lock failed.
D C – Messages Switch Properties Dialog Table C-4. Switch Properties Dialog Messages (Continued) Message 59048-04 Rev. B User Action Duplicate domain ID specified. Verify that all information is valid and retry the configuration change. Consult the documentation for valid configurations. Valid domain IDs must be in the range 1 to 239, and must be unique within a fabric.
D C – Messages Switch Properties Dialog Table C-4. Switch Properties Dialog Messages (Continued) Message C-6 User Action Out of range domain ID specified. Verify that all information is valid and retry the configuration change. Consult the documentation for valid configurations. Valid domain IDs must be in the range 1 to 239, and must be unique within a fabric. If the fabric contains SANbox with E_Port switches, then all domain IDs must be in the same range of sixteen values: 1…16, 17…32, and so on.
D C – Messages Switch Properties Dialog Table C-4. Switch Properties Dialog Messages (Continued) Message 59048-04 Rev. B User Action Unable to apply changes. Failed to obtain admin privileges. Verify that another user is not currently modifying the switch configuration, using either the management application, or a telnet login, or any application.
D C – Messages Port Properties Dialog C.5 Port Properties Dialog Table C-5. Port Properties Dialog Messages C-8 Message User Action Invalid value entered for interop credits. Or Failed to set I/O stream guard change. Or Failed to set new interop credits. Or Request to save and activate config failed. Or Received error in attempting to edit switch configuration. Or Received error in attempting to save switch configuration. Or Received error in attempting to activate switch configuration.
D C – Messages Port Properties Dialog Table C-5. Port Properties Dialog Messages (Continued) 59048-04 Rev. B Message User Action Unable to apply changes. Failed to obtain admin privileges. Verify that another user is not currently modifying the switch configuration, using either the management application, or a Telnet login, or any other application, and then retry the operation. Unable to confirm that port changes were successful.
D C – Messages Faceplate Display C.6 Faceplate Display Table C-6. Faceplate Display Messages Message C-10 User Action Failed to clear the trap log. Verify that the user has permissions to modify the configuration on the switch, that the switch is reachable in the fabric, and that the fabric is reachable from the user’s workstation, then retry the configuration change. Necessary information is missing for this switch. Firmware version on this switch is unsupported.
D C – Messages Faceplate Display Table C-6. Faceplate Display Messages (Continued) Message 59048-04 Rev. B User Action Request for switch reset failed because admin access was not available. Verify that another user is not currently modifying the switch configuration, using either the management application, or a telnet login, or any application, and then retry the operation. Reset will complete shortly. There will be a brief loss of connectivity with switch.
D C – Messages Faceplate Display Table C-6. Faceplate Display Messages (Continued) Message C-12 User Action The zoning information you are about to edit is incomplete. If you apply changes you will possibly lose zoning information. The application has not been able to completely read the current zoning database from the switch. If the user edits the incomplete database information and applies the changes, then any information which has not been read from the switch will be lost.
D C – Messages Firmware Fallback Dialog C.7 Firmware Fallback Dialog Table C-7. Firmware Fallback Dialog Messages Message User Action Attempt to revert to fallback firmware failed The switch was unable to fall back to the previous firmware. Correct the problem specified and retry the operation. Request to get admin privileges failed.
D C – Messages Load Firmware Dialog Table C-8. Load Firmware Dialog Messages (Continued) Message C-14 User Action Firmware upload complete. The switch must be reset to activate new firmware. Reset now? The new firmware will not be executed until the switch is reset. Resetting a switch in the fabric will cause the servers and storage systems attached to the fabric to lose communications until the switch reset is complete and the fabric has reinitialized.
D C – Messages Port Loopback Test Dialog C.9 Port Loopback Test Dialog Table C-9. Port Loopback Test Dialog Messages 59048-04 Rev. B Message User Action Attempt to put port in diagnostic state has failed. Unable to continue with port test. Verify that the user has permissions to modify the configuration on the switch, that the switch is reachable in the fabric, and that the fabric is reachable from the user’s workstation, then retry the configuration change.
D C – Messages Port Loopback Test Dialog Table C-9. Port Loopback Test Dialog Messages (Continued) C-16 Message User Action Switch is currently unreachable. Unable to accurately report status of port test. The application lost communications with the switch while the switch was running the loopback tests, and could not determine whether the tests completed. If the problem was temporary, restart the loopback tests. The port selected for online port test must be online with active login.
D C – Messages Extended Credits Wizard C.10 Extended Credits Wizard Table C-10. Extended Credits Wizard Messages Message User Action Request for admin failed. Verify that another user is not currently modifying the switch configuration, using either the management application, or a telnet login, or any application, and then retry the operation.
D C – Messages Zoning Dialog Table C-11. Zoning Dialog Messages (Continued) Message C-18 User Action Error saving zoning Verify that the specified zoning configuration file exists on a file system that is reachable, and that the user has permissions to write the file. Failed to obtain admin privileges Verify that another user is not currently modifying the switch configuration, using either the management application, or a telnet login, or any application, and then retry the operation.
D C – Messages Zoning Dialog Table C-11. Zoning Dialog Messages (Continued) 59048-04 Rev. B Message User Action The zone set you attempting to activate contains port based zoning and there are switches in the fabric that might not support this type of zoning. Some E_Ports may isolate. Do you wish to continue? Not all switch vendors support port-based zoning. Consult the manual for these vendors’ switches to determine whether to apply this zoning configuration to the fabric.
D C – Messages Restore Configuration Dialog C.12 Restore Configuration Dialog Table C-12. Restore Configuration Dialog Messages Message User Action Failed parsing filename Verify that the file specified is a valid archive file, and retry the operation. Possibly failed check switch! The application lost communications with the switch while restoring the archived configuration, and could not determine whether the operation completed. If the problem was temporary, retry the operation.
D C – Messages Trap Configuration Dialog C.14 Trap Configuration Dialog Table C-14. Trap Configuration Dialog Messages Message 59048-04 Rev. B User Action Invalid rising threshold Or Invalid falling threshold Or Invalid sample interval. Verify that the information is correct and then retry. You must wait for trap information to be read first. Or You must wait for alarm threshold information to be read first.
C – Messages Trap Configuration Dialog D Notes C-22 59048-04 Rev.
Glossary Access Control List Zone Access Control List zoning divides the fabric for purposes of controlling discovery and inbound traffic. Arbitrated Loop A Fibre Channel topology where ports use arbitration to establish a point-to-point circuit. Active Zone Set The zone set that defines the current zoning for the fabric. Arbitrated Loop Physical Address (AL_PA) A unique one-byte value assigned during loop initialization to each NL_Port on a loop.
D SANbox2-64 Switch Management User’s Guide Class 3 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports without acknowledgment. Fabric View File A file containing a set of fabrics that were opened and saved during a previous SANbox Manager session. Configured Zone Sets The zone sets stored on a switch excluding the active zone set. Fan Fail LED An LED that indicates that a cooling fan in the switch is operating below standard.
D SANbox2-64 Switch Management User’s Guide Initiator The device that initiates a data exchange with a target device. Management Workstation PC workstation that manages the fabric through the fabric management switch. In-Order-Delivery A feature that requires that frames be received in the same order in which they were sent. Mesh Topology A fabric in which each chassis has at least one port directly connected to each other chassis in the fabric.
D Port Status LED A dual-function port LED on a SANbox2-64 switch that indicates device login or loop initialization status, and port activity. POST Power On Self Test Power On Self Test (POST) Diagnostics that the switch chassis performs at start up. Principal Switch The switch in the fabric that manages domain ID assignments. SANbox Manager Switch management application. SFP Small Form-Factor Pluggable.
Index A access control list zone 3-15, 3-28 account name 3-3, A-1 active firmware 4-34 active zone set 3-12, 3-15, 4-25 Active Zoneset data window 3-12 Admin account name A-6 authority A-6 admin authority 3-1 Admin command A-7 administrative state blade 5-2, A-32 configured 4-22, 5-2, 6-11 current 4-22, 5-2, 6-11 I/O blade 5-2 port 6-11, A-47 switch 4-22, A-33 alarm configuration 4-16, A-38 configuration display A-67 log A-32, A-53 alias add members 3-29, A-8 copy A-8 create 3-28, A-8 delete A-8 delete memb
D SANbox2-64 Switch Management User’s Guide copy A-10 delete A-10 edit A-10 list A-10 reset A-27 restore 4-30, A-11 save A-11 configured administrative state 4-22 contact 4-28 CRC error 4-16 credits 6-14 current administrative state 4-22 D data window Active Zoneset 3-12 Blade Information 5-1 Configured Zonesets 4-15 description 2-24, 2-27, 2-30 Name Server 4-8, 6-9 port information 6-7 port statistics 6-4 switch 4-10 database fabric 3-3 zoning 3-19 date 4-18 Date command A-13 Decode error 4-16 default c
D SANbox2-64 Switch Management User’s Guide port 6-2, 6-12 rediscovery 3-5 security 3-1 status 3-7 tree 2-23 zoning 3-13 Fabric Device Management Interface A-54 fabric services 3-2 Fabric View arrange graphs B-6 customize graphs B-6 display graphs B-5 preferences B-4 start B-2 fabric view file B-4 auto save B-4 open 3-4, B-3 password B-2 save 2-14, 3-5 faceplate display data window 2-30 description 2-17, 2-28 open 2-27 popup menu 2-30 factory defaults 4-32, A-27 Fallback command A-14 Fan Fail LED 4-36 FC-
D SANbox2-64 Switch Management User’s Guide N IP address 4-27 configuration 4-27 ISL monitoring 4-16 L layout 2-26 legacy address format 4-25 link delete 3-7 selecting 2-26 status 2-25 Link data window 4-13 link state database A-54 Lip command A-22 log archive A-44 clear A-44 event A-44, A-70 power-on self test A-57 logged in users A-58 login limit 3-4, A-2 monitoring 4-16 logout monitoring 4-16 loop port bypass A-47 enable A-47 fabric 6-2, 6-12 generic 6-13 initialization A-22 loopback test 6-16 loss o
D SANbox2-64 Switch Management User’s Guide donor 6-14 extending credits 6-14 external test A-79 initialize A-27 internal test A-79 loopback test A-79 mode 6-2 numbering 2-29 online test A-79 operational information A-55 operational state 6-3 performance A-55, A-73, B-1 recipient 6-14 reset 6-16 selecting 2-29 speed 6-3, A-47 status 2-29 test 6-16 view 2-15, 2-29 Port Information data window 4-14, 6-7 Port Statistics data window 4-13, 6-4 port/device tree 3-20 power on self test log A-57 preferences Fabri
D SANbox2-64 Switch Management User’s Guide trap configuration 4-29 slot number 2-29, A-57 SNMP enabled 4-28 soft zone 3-14, 3-28 static boot method 4-27 status icon color 2-23 steering A-57 subnet mask address 4-27 switch add 3-5 administrative state 4-22, A-33 configuration 4-20, A-37 configuration display A-67 delete 3-7 displaying information 4-7 hard reset 4-20, A-15 hot reset 4-20 icons 3-8 location 4-28 manufacturer information A-75 operational information A-58 paging 4-18 properties 4-21 replace 3
D SANbox2-64 Switch Management User’s Guide add member port 3-26, A-87 copy 3-23, A-87 create 3-25, A-87 definition 3-14 delete A-87 delete member port A-88 list A-88 list members A-88 name server 3-14 remove 3-23, 3-27 remove all 3-27 remove member port 3-27 rename 3-27, A-88 soft 3-14 type 3-28, A-88 Zone command A-87 zone merge description 3-18 failure 3-18 failure recovery 3-18 zone set activate 3-23, A-91 active 3-12, 3-15, A-93 add member zone A-91 copy A-91 create 3-22, A-91 deactivate 3-23, A-28,
D SANbox2-64 Switch Management User’s Guide Notes Index-8 59048-04 Rev.
