user manual

ManualsBrandsQ-See ManualsSecurity CameraDigital Peripheral Solutions Security Camera QR

Dynamic Domain Name Service (DDNS) provides the capability for a networked device using the

Internet Protocol Suite to notify a DDNS host to change the active DNS configuration of its

hostnames or addresses. This is a useful feature that your Q

and can be helpful in avoiding any issues that might occur due to frequent or unplanned

changes to your Public/WAN IP address. Enabling DDNS on your Q

you to connect to your device through a DDNS host such a

this ability on your Q-See

DVR system

User Manual for this device. Once you have enabled Port Forwarding, you can configu

DDNS information by following these steps:

Using a computer that is connected to the same network as your Q

Browser to go to

http://myq

Click on the New User? Link at the bottom of

Complete the registration process by following the on

[Submit] button at the

bottom of your screen (Figure 1

Dynamic Domain Name Service (DDNS) provides the capability for a networked device using the

Internet Protocol Suite to notify a DDNS host to change the active DNS configuration of its

hostnames or addresses. This is a useful feature that your Q

-See DVR system

and can be helpful in avoiding any issues that might occur due to frequent or unplanned

changes to your Public/WAN IP address. Enabling DDNS on your Q

-See

DVR system

you to connect to your device through a DDNS host such a

s myq-see.com

. In order to facilitate

DVR system

, you must first set up Port Forwarding as directed in the

User Manual for this device. Once you have enabled Port Forwarding, you can configu

DDNS information by following these steps:

Using a computer that is connected to the same network as your Q

See

http://myq

-see.com.

Click on the New User? Link at the bottom of

your page (http://myq-

see.com/reg.asp

Complete the registration process by following the on

screen directions and click the

bottom of your screen (Figure 1

(Figure 1)

Dynamic Domain Name Service (DDNS) provides the capability for a networked device using the

Internet Protocol Suite to notify a DDNS host to change the active DNS configuration of its

is equipped with

and can be helpful in avoiding any issues that might occur due to frequent or unplanned

DVR system

will allow

. In order to facilitate

, you must first set up Port Forwarding as directed in the

User Manual for this device. Once you have enabled Port Forwarding, you can configu

re your

See

DVR, use your IE

see.com/reg.asp

screen directions and click the

Summary of content (3 pages)

PAGE 1
MYQ-SEE DDNS SETUP GUIDE FOR QR, QSDR, AND QSD9004 DVRS Dynamic Domain Name Service (DDNS) provides the capability for a networked device using the Internet Protocol Suite to notify a DDNS host to change the active DNS configuration of its hostnames or addresses. This is a useful feature that your Q Q-See DVR system is equipped with and can be helpful in avoiding any issues that might occur due to frequent or unplanned changes to your Public/WAN IP address.
PAGE 2
(Figure 2) d. The next screen will ask you tto create a domain name.. Domain names must start with an (a-z) or (0-9) 9) and cannot contain a hyphen. Once you choose your domain name, click on the [Request Domain] button. This will generate a confirmation screen which tells you if your Domain name is available and list an IIP P address (Figure 2). Verify that this is your current IP Address by going to www.myipaddress.
PAGE 3
f. Clicking on Network will generate a Network settings dialog box as illustrated in Figure 4. Click on the [DDNS SETUP] button to generate a DDNS setting dialog box as illustrated in Figure 5. (Figure 4) NOTICE: You need to put your public DNS. This can be found in your Router Status tab. Usually there are 2 DNS entries (DNS1 & DNS2). Use DNS 1 only. If you router does not list the DNS address get it from your Internet Service Provider. g.