Technical Manual

ManualsBrandsQ-See ManualsCamerasQ-See QD6523ZH

14 15

ADDITIONAL SETTINGS USING THE CAMERA’S ON-SCREEN MENU

The QD6532Z offers additional features that can be accessed through the DVR’s

PTZ menu, but which are actually programmed on the camera itself.

Accessing the Menu

The following instructions are shown using a QT-series DVR.

STEP 1.

Right-click on your screen to open the Control Bar.

STEP 2. Click on the PTZ Control icon.

EXAMPLE 1: SETTING A CRUISE

This example is based on using a QT-Series DVR without an attached PTZ

keyboard. Your DVR’s speciﬁc commands may differ slightly. Please consult your

system’s manual.

STEP 1. In your DVR’s PTZ settings

window, select the Advanced tab

and then Preset 1.

STEP 2. Rotate the camera to the

desired position using the arrow

controls.

STEP 3. Click Save

STEP 4. Select Preset 2.

STEP 5. Rotate camera to desired

second location.

STEP 6. Click Save

You may repeat Steps 4-6 for additional

positions if desired.

STEP 7. While still in the Advanced

tab, click on the Setting button in

the Cruise column for Channel 1.

This will open a new window.

STEP 8. Click Add.

STEP 9. Double-click on the new

cruise setting to begin loading

your presets.

STEP 10. Click on the + button to

open the Preset pop-up window

and select your starting preset

point, speed and stop time.

Speed: 1-8 with 8 being the fastest

Serial PortSerial Port AdvancedAdvanced

P.T.ZP.T.Z

DefaultDefault

SettingSetting

ApplyApply ExitExit

CH Preset Cruise Track

SaveSave

Zoom

Focus

Iris

Zoom

Focus

Iris

Speed: 5Speed: 5

No.No.

02020101 0303 0404 0505 0606 0707 0808 AllAll

Start TrackStart Track

Start Auto ScanStart Auto Scan

Start CruiseStart Cruise

Preset

Cruise

Preset

Cruise

Speed: 5Speed: 5

preset 101preset 101

02020101 0303 0404 0505 0606 0707 0808 AllAll

Zoom

Focus

Iris

Zoom

Focus

Iris

Time: This is the time the camera will stay pointed at this location.

STEP 11. Repeat for each preset - up to a maximum of 16 per cruise.

STEP 12. Click OK save your settings and close the windows until you reach

the PTZ Settings window. Click Apply to save all of the settings.

STEP 13. Open the PTZ controls from the Control Bar, select your cruise in the

pull-down and click

to begin.

EXAMPLE 2: SETTING A TRACK

An alternate method is to utilize the Track settings - also found in the Advanced

tab. Click the Track button for the right channel, use the directional controls to point

the camera at your desired starting point and then click Start Record. The DVR

will then record your movements, including delays at selected spots. Click Stop

Record to end. Clicking on Start Track in the PTZ control window will start the

camera on its track.

Start TrackStart Track

Start Auto ScanStart Auto Scan

Start CruiseStart Cruise

Preset

Cruise

Preset

Cruise

Speed: 5Speed: 5

preset 28preset 28

02020101 0303 0404 0505 0606 0707 0808 AllAll

Zoom

Focus

Iris

Zoom

Focus

Iris

STEP 3. Set the preset point (a)to 28 (95 may also be used)

STEP 4. Click the

to the right of the Preset pulldown (b).

STEP 5.

The on-screen menu will appear. You can navigate through it using the PTZ

directional controls (c). Use the Iris + button (d) as “Enter” to make selections

Use the right arrow in menus with multiple options.

SYSTEM SETTING

DISPLAY SETTING

CAMERA SETTING

FUNCTION SETTING

ALARM SETTING

EXIT

The Menus

When the On-Screen Display is activated, a menu with six options will be displayed.

The ﬁve menus all have submenus and other options. Most functions are self-

explanatory in nature. Selected features will be covered below.

SYSTEM INFORMATION

ADDR INFORMATION

SET NORTH

LANGUAGE: ENGLISH

FACTORY DEFAULT

RESTART

BACK EXIT

Back will take you to the previous menu

while Exit will close out of the menu.

SYSTEM SETTING MENU

The ﬁrst two selections show information

regarding the camera’s address, baud rate,

and etc. These cannot be changed. The

language cannot be changed as well.

North: Exit the menu, point the camera

north and return to the menu. Select Set

North. “OK” will brieﬂy ﬂash on screen to

indicate that North has been set.

Restart: This will restart the camera and

it will go through its start-up cycle but will

not clear user settings.

IMPORTANT! Preset 24 through 34 and 79 through 99 are reserved for

camera commands and cannot be used as preset points.