QSD371614C4-250 User’s Manual Contact US: Q-See Products 8015 E. Crystal Dr Anaheim, CA 92807 Website: http://www.q-see.com Customer Service: Phone:877-998-3440 X 538 Email:cs@dpsi-usa.com Tech Support: Phone:877-998-3440 X 539 Email:ts@dpsi-usa.
TABLE OF CONTENTS 1. INTRODUCTION .................................................................................................................2 2. DVR FEATURES .................................................................................................................2 3. PHYSICAL UNIT .................................................................................................................3 3.1 Front Panel.....................................................................................
Operation Manual-4CH Duplex DVR 6.8 Exit .......................................................................................................................... 21 7. PLAYBACK WITH TIME SEARCH FUNCTION ...............................................................21 8. BACKUP via USB Flash Drive ..........................................................................................22 9. RECORDING LENGTH .................................................................................................
Operation Manual-4CH Duplex DVR 1. INTRODUCTION The QSD371614C4-250 system provides a total 4-channel digital video security surveillance system supporting duplex (simultaneous playback and record) functionality. You can use front panel buttons, remote control unit or mouse to operate all DVR menu settings. The functionality of each access option is exactly the same. 2. DVR FEATURES ● True Duplex Functionality: Simultaneous Play/Record. ● PAL/NTSC Options.
Operation Manual-4CH Duplex DVR 3. PHYSICAL UNIT 3.1 Front Panel ● IR Remote Receiver ● LED Light (a) GREEN (PWR): The DVR unit is powered up and running. (b) RED (HDD): System is in Recording Mode or in Playback Mode. Some DVR is provided with touch-tone front panels. A series of buttons on the DVR front panel operates the system’s basic functions, such as recording, playback, fast-forward, reverse, etc. For more details about the DVR menu, refer to “6. SETUP”.
Operation Manual-4CH Duplex DVR [Input: AC 100-240V, 50/60Hz, 1.5A / Output: DC +12V == 3A] ● PS/2 MOUSE PORT Use this port for PS/2 mouse connection. If you have USB port mouse, use USB - PS/2 adapter to connect with this port. ● Fan 3.3 Remote Control The buttons on the DVR remote control unit operates the system’s basic functions, such as recording, playback, fast-forward, reverse, etc. For more details about the DVR menu, refer to “6. SETUP”.
Operation Manual-4CH Duplex DVR ⑺ ■ (STOP) To stop playback, press the “STOP” button. ⑻ ► (PLAY) After recording, press “PLAY” button to start video playback. Playback will start with the oldest unread video data and then continue playing. ⑼ ►►(FWD) This is the fast forward button. To play the recorded video faster, press the “FWD” button. There are three levels of fast forward playback speed. (a) FF 1 (►►) : Play two times faster (2x) than the normal play.
Operation Manual-4CH Duplex DVR If you are using a Mouse it must be connected to DVR before you startup system. Connect the power adapter to the DVR this will turn on the DVR. Make sure that a hard drive and camera(s) are properly installed. Start TV Monitoring and Recording. After installation of hard drive, the hard drive must be fixed tight enough with screws. If the power is turned off while recording (i.e.
Operation Manual-4CH Duplex DVR Connect “VIDEO IN” of the monitor to “VIDEO OUT” of the DVR system using the BNC to RCA cable that comes with the DVR. 5.3 Camera Connection Connect the included video cables to the “VIDEO IN” of your DVR and “VIDEO OUT” of the camera with video cable and plug in the camera’s power adapter to the power feed of the video cable near the DVR. “VIDEO OUT” on CAMERA “VIDEO IN” on DVR 5.4 Mouse Connection If you use a PS/2 mouse connect it to the port below on the system.
Operation Manual-4CH Duplex DVR 5.5 DVR Power Connection Connect the DVR power adapter to the adapter jack at the rear panel of the DVR unit. It will boot up the system. If users install a new hard drive, it will ask you to format the hard drive before the system starts to run (Below Fig). Choose format option by pressing the “PLAY” button. Below is the information of input/output voltage for the power adapter: Input: AC 100-240V, 50/60Hz, 1.5A Output: DC +12V == 3A 6.
Operation Manual-4CH Duplex DVR operate live video display and image playback, or modify some parameter values that are independent of recording. If user does not have the right to modify the parameter value, there will be an identifier “ ” on top right corner of the screen. A: Mouse Control After system boot-up, hold the right mouse button and the login window will open. Hold the left mouse button to select the “Account”, and input correct account.
Operation Manual-4CH Duplex DVR Logout Channel auto sequence. The iron “ ” won’t display if the order of “auto sequence” is “OFF”. Move the mouse up or down to move the cursor. Click a left mouse button to change the settings. Click a right mouse button to go back to the previous. Hold the left mouse button to click the icon “ ”. You will see the screen below on the monitor (Fig (b)).
Operation Manual-4CH Duplex DVR option you can change the name of each channel if you want to. 6.2 Record Use this option to enable recording on the channel (1,2,3,4). Only selected channels will be recorded no matter how many camera channels are displayed on the screen. A: [RECORD FRAMERATE] Set the recording frame rate for each channel. The higher the recording frame rate, the more natural movement you will see while playback. You can set each channels frame rate independently.
Operation Manual-4CH Duplex DVR which means the system will record 48 frames per second with all channels. User can set frame rate as 3~25 frames per second with each channel. The max value of total frames per second with all channels is 50 frames. For NTSC video output format, system default value is 15 frames per second with each channel, which means the system will record 60 frames per second with all channels. User can set frame rate as 3~30 frames per second with each channel.
Operation Manual-4CH Duplex DVR pressing the [QUAD] button on the DVR front panel or remote control, or using the left mouse button to click the time period 24. - Grey bar: No recording will be made for this time period unless user activates manual recording. - Red bar: The time period with a red bar will continuously record (Time record) unless you manually stop recording during that time. - Green bar: The system will record whenever motion is detected. (See the following chapter “MOTION DETECTION”) 6.
Operation Manual-4CH Duplex DVR C: [MOTION DETECTION] [CHANNEL] Select the channel or channels (1,2,3,4) that you want to record when motion is detected. [SENSITIVITY] You can adjust the sensitivity of the built-in motion sensor on the DVR system. The higher the number, the higher the sensitivity is. Values are “1, 2, 3, 4, Off”. The maximum sensitivity level is 4. [MOTION AREA] Use this option to select the size of the area that you want to be sensitive to motion.
Operation Manual-4CH Duplex DVR 6.4 Screen [BORDER] User can make the white borderline around each channel appear or disappear by setting this option to “on” or “off”. [AUTO SEQUENCE] This option is used to setup the channels to appear one at a time on the screen in automatic sequence, and select the time that each channel appears on the screen before switching to the next channel. Values are “Off, 1 to 10 seconds”. Default is “Off”.
Operation Manual-4CH Duplex DVR In this menu, you can see the information of the hard drive installed in the DVR, change the system password, adjust keypad tone, access browser event list or adjust current time on the system. If user logs into the system at admin level, the menu bar will be displayed as Fig (c). The user can enter into the “account” option to examine all user accounts, and add or delete users (Please refer to section “6.6.2” for account setup).
Operation Manual-4CH Duplex DVR password is “111111”. Type the password and press any key button. When HDD is formatting, and has successfully formatted, you will see the message below blinking. If the password is incorrect, you will see the below message blinking. Then try to enter the right password again. 6.5.
Operation Manual-4CH Duplex DVR can be used as user account or password. Press 「SEL」to input value, and move the prompt to the “Enter” option press 「SEL」to confirm. Use CH1 for up, CH2 for down, CH3 for left, CH4 for right, Press “Shift” for change characters. [Level] Move the cursor to change the highlighted option to Level, and then press [SEL] to adjust user level (operator/guest). 6.5.3 Password Setup The default password is 111111. All numbers, letters and signs in the pane can be used in passwords.
Operation Manual-4CH Duplex DVR you choose OFF, the account information will be kept when you logout of the system. 6.5.5 Keypad Tone Set the keypad tone to “ON” or “OFF” to enable or disable keypad tone during operation. 6.5.6 Time Set You can adjust the current time, date and year at any time by region. Set your region first and set the current time so that the video back-up data can be played with the correct time displayed. Date and Time format are below.
Operation Manual-4CH Duplex DVR previous event according to input time period if the data hasn’t been over-written. To playback by Event list, using [UP]/[DOWN] or channel number (CH3 for Page Up or CH4 for Page Down) key on the front panel or remote control, select the event that you want to playback and press “PLAY” button.
Operation Manual-4CH Duplex DVR 6.8 Exit After you change settings on DVR menu, you need to confirm the changes under the EXIT menu. [EXIT & SAVE CHANGE] Save change and go back to main screen. [EXIT & DISCARD CHANGES] No change and go back to main screen. [LOAD SETUP DEFAULT] Load default settings. 7. PLAYBACK WITH TIME SEARCH FUNCTION This is an enhanced playback option, which enables the user to manually select a specific starting time for playback.
Operation Manual-4CH Duplex DVR to change the value of the playback date and start time, then press the right mouse button. Then use the left mouse button to click “Search”, the playback will start from the date & time selected by the user. 8. BACKUP via USB Flash Drive Our 4-channel DVR system has an enhanced back-up feature so that it’s possible to transfer the video files recorded on the hard drive to USB flash drive.
Operation Manual-4CH Duplex DVR It will take a few minutes to copy the video data onto a USB flash drive. The file size number is going up until it’s done while displaying the messages below: WRITING… Then it will show the following message on the screen: FIXATING… Take out the USB flash drive and attach it to your PC when it’s done. Press “PLAY” button to continue on the system. To view the video files saved on back-up devices on the computer, you need to use the software provided with this package. 9.
Operation Manual-4CH Duplex DVR Select setup option. Set up the install directory. Execute: Start >Program> Vx4SLPlayer. 10.2 Program Interface Double click icon “ ” on desktop to run the program. 10.
Operation Manual-4CH Duplex DVR 1) Click “ ” to play the video recorder in “*.VVF” format. 2) Still Capture Click “ ” to capture single frame. Click the right mouse button to select “Options…” to 1. Open File 2. Fast Reverse 3. Rewind 4. Previous Frame 5. Pause 6. Next Frame 7. Play 8. Fast forward 9. Still Capture 10. Split 1 11. Split 4 12. Volume Scroll Bar 13. Mute On/Off 14. Playing Scroll Bar 15. Minimize the window 16.
Operation Manual-4CH Duplex DVR setup path to save image. Click the left mouse button to select folder that you want to save to, for example select the folder as “E:\VOC 4CH\backup”. 3) In “Options” window, you can setup other menu selections such as “General & On screen display date/time format”. □√ Always on top (A): The client window will always display on top of all the windows. □√ Use DirectDraw: Show the run dialog to your graphic card.
Operation Manual-4CH Duplex DVR audio option is not available. Next click “ “ ” to select input file and output file, and click ” to select video compression mode. Finally click “ ” to start, and progress will be showed as a percentage. Notes: 1. When selecting video compression mode, user should test the compression that he selects to see if it is matching his computer. If it doesn’t match the computer may not be able to play the file. 2.
Operation Manual-4CH Duplex DVR The “Output Size” is the size of output file. Left click “ click “ ”. 28 ” to setup save path.
Operation Manual-4CH Duplex DVR 11. APPENDIX 11.1 QSD371614 4CH DVR series - compatible USB Flash Drives. In case noise occurs on USB line due to a variety of reasons such as power noise, it might cause an error during the data transferring process. In this case, it requires re-transferring the date to the flash drive. If the device can process things normally in these exceptional cases, things are okay. However, in some cases, it doesn’t operate normally.
Operation Manual-4CH Duplex DVR 11.2 Specifications ITEM 4CH DVR Video Format NTSC / PAL Operation System Linux Video Input 4 channel Composite BNC Video Output 1 channel Composite BNC PAL: 100fps (4*25fps); Display Speed NTSC: 120fps (4*30fps); PAL: Max. 50 frame per second;3fps~Max 25fps(each channel adjustable); Recording Speed NTSC: Max. 60 frame per second;: 3fps~Max.
Operation Manual-4CH Duplex DVR 11.3 System Connection Diagram Note: We STRONGLY recommend that you plug the DVR and cameras into a Transient Voltage Surge Protector (UL-1449 rating). Look for a clamping voltage of 330 or lower, Joule rating of at least 400, and a response time of 10 nanoseconds or less. 11.
Operation Manual-4CH Duplex DVR 11.5 Q-SEE Product Warranty Thank you for choosing our products. All of our products users have a conditional free warranty repair service for hardware within 12 months starting from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software.
Operation Manual-4CH Duplex DVR If you have questions: Contact Us: Mailing Address: DPS Inc. 8015 E. Crystal Dr Anaheim, CA 92807 Customer Service: Phone: 877-998-3440 x 538 Email: cs@dpsi-usa.com Website: http://www.q-see.com Fax: 714-998-3509 Tech Support: Phone: 877-998-3440 x 539 Email: ts@dpsi-usa.