QSD9004 & QSD9008 User’s Manual Contact US: Q-see Products 8015E.Crystal Dr Anaheim,CA92807 Website: http://www.q-see.com Customer Service: Phone:877-998-3440 x 538 Email:cs@dpsi-usa.com Tech Support: Phone:877-998-3440 x 539 Email:ts@dpsi-usa.
CONTENTS Chapter 1: DVR Features...................................................................................................................................................2 Chapter 2: Layout ................................................................................................................................................................3 2.1 Front Panel .......................................................................................................................................
5.2.6.5 Motion Detect ................................................................................................................................................23 5.2.7 System Function................................................................................................................................................24 5.2.7.1 Time Set .........................................................................................................................................................24 5.
User Manual Safety Instruction 1. Use proper power source. Do not use this product with a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electric shock. 3. Do not operate in wet & dusty area or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
User Manual Chapter 1: DVR Features Real time monitoring Supports real time surveillance via Monitor Saves Recordings DVR saves real-time recording image to HDD Backup Recordings Supports DVR backup via USB flash drive and hard drive.
User Manual Chapter 2: Layout 2.1 Front Panel 2.1.1 4-Channel Front Panel 1 2 3 4 7 Item Key title/Indicator 1 Power Switch 2 Power indicator 3 IR Receiver 4 HDD indicator 5 Channel Select: CH1 CH2 CH3 CH4 6 QUAD 5 8 9 10 6 11 12 16 15 17 Turn Power on and off PWR If the “Green” indicator is on the system is getting power Receives signal from Remote Control HDD When the “Red” indicator flashes it means the hard drive is being read or written to.
User Manual 2.1.
User Manual 8 RS-485/Sensor/Alarm RS485/Sensor/Alarm interface (see pin outs below) 9 Power Port Connect power supply - DC12V 3A List 2-2 2.2.
User Manual 2.
User Manual Chapter 3: DVR Installation 3.1 Hard Drive Installation Caution： Please do not Install or take out hard drive when DVR is running! (1) Remove screws and open DVR upper cover carefully; (2) Insert Power Cord and data cable into Pin of hard drive securely; (3) Put the upper cover back carefully, re-attach screws. 3.2 Camera and Monitor Connection Connect camera cable to video input of DVR, and from video output of DVR to Monitor via BNC connector (Refer to section2.
User Manual Chapter 4: DVR Boot up 4.1 System Initialization After connecting the power adapter and turning On the power button, the system will boot-up and start initializing. Picture 4-1 4.2 Main Interface Picture 4-2 After finishing system initialization the system will enter into main interface. Picture 4-2 is the main interface displayed by system, which is showing no video input status. Once there are video inputs, the interface will display live images from the cameras.
User Manual 5.1 Main Menu Preview Camera Color set Recording Search Network Playbac Rec. Detail File File Backup Main Menu HDD Alarm Setting Device Manageme E-mail PTZ Setting Mobile Motion Area setting Time Setting User Video Setting System Language Select System Information System Maintenance 5.2 Main Menu Picture 5-2 After clicking right button of mouse, pop-up menu will be displayed on the screen.
User Manual 5.2.1 Camera setup Go to [Main Menu Camera] to set up the name display and position display of each channel (Shown as Picture 5-3), You can also adjust image brightness, saturation, contrast and hue settings of each channel after entering into [Color] Menu and set up whether each channel can be previewed or not under Live display and/or Recording mode. Please note that the name of each channel supports up to eight characters or four Chinese characters.
User Manual Recording options include All, CH-1, CH-2, CH-3, CH-4 respectively. Please click the channel you need, the channel you select will be highlighted in “Blue” unselected channels will be “Grey”. To setup weekly schedules, click on the box of the recording status you want (Alarm, General, or No Record) and then click on each box in the schedule time line that you want this method to apply to.
User Manual (Picture 5-9), then type ipconfig at the prompt (RED arrow on Picture 5-9) to access the router settings. Write down the gateway and subnet mask numbers (GREEN arrows on (Picture 5-9) so you can copy them into the network settings on the DVR (Picture 5-10).
User Manual When you access the DVR from a remote computer you also need to use a different address in the Internet Explorer browser window. Instead of entering the IP address of the DVR you need to enter the public IP address of the router the DVR is attached to. You can get this address by going to www.myipaddress.com from a computer that is attached to the same router as the DVR. This Picture 5-14 website will display the box in Picture 5-14 below that shows the IP address you need to use.
User Manual To connect to the DVR from the remote computer you would then open an Internet Explorer browser window and enter the internet IP of your router that you got by going to www.myipaddress.com. Notice: If you cannot use HTTP port 80 or 9000 because it is being used by another program, or it is being blocked by your service provider, you can use another port in the same range.
User Manual First ： Indicates the first page of recording history you have searched. When you view other pages, clicking [First] button brings you back to Page one. PRE (Previous page): When viewing event list, clicking [Previous page] button will take you back to page before the one you are currently viewing (except the first page). NEXT (Next page): When viewing event list, clicking [Next page] button will take you to the page after the one you are currently viewing (except the last page).
User Manual 3、Open backup file: （1）、Click [Play] menu (P) on the top of multimedia player interface to select playing the backup file; Picture 5-26 （2）、Click pop-up menu button on the bottom of multimedia player and [Play- ] button, then the backup file will be played on the according channel. （3）、The Menu brief on the bottom of multimedia player: recording date for the current backup file shown as right corner; Date: 24H recording time: lie under [Date] menu.
User Manual Picture 5-27A 5、Refer to the below for [Audio on] setting procedure. (Setting parameter will be available after re-starting multimedia player after [Audio on] set up.) Setting Audio channel setting Normal video Bar Select the channel you want to playback the audio Select the channel has audio files Apply OK. Picture 5-28B Picture 5-28A After successfully setting the above, when you playback the current channel, you can open the channel’s audio function at the same time as the video 5.2.
User Manual OVERWRITE: If you select “on” the system will automatically overwrite the oldest recordings once the hard drive is full; if you select “off”, recording will stop once the hard drive is full. HDD FORMAT: You use this option to format the hard drive, you can not record files to the hard drive until it has been formatted. Click [Format HDD] button to start formatting.
User Manual On the [Email setup] mode, refer to its parameter setup shown as picture 5-34 when setting email alarm to “on”. SSL: is a security link transport protocol. You can encrypt your communication info (including your email) using SSL to prevent hackers from monitoring your email or communication info and even your password. Picture 5-34 Please set SSL to “On” via Gmail.com server, and set to “Off” via other mail server.
User Manual 5.2.6.3 PTZ Setup Enter into [Main menu Device PTZ Setup] to select the PTZ channel you want to control and set PTZ protocol (Pelco-D, Pelco-P), Baud rate (1200, 2400, 4800, 9600), Data bit (8, 7, 6, 5), Stop bit (1, 2), Parity Check （None, Odd, Even Mark Space）and address code respectively. Please note the above-mentioned channel settings must match the settings of the PTZ camera. Picture 5-36 5.2.6.4 Mobile Click [Main menu Device Mobile] to enter into [Mobile] menu.
User Manual 2. Click the windows mobile folder (red box in Pic 1) and choose the file QQeye” Select the file which will open the window in Pic 3. The file is generally faulted to save as Device, direct to phone, (shown in Pic 3) but you can save it to Device or Storage Card. 3. Choose storage location and click [Install] button (red box in Pic 3) to start the installation (please refer to display in Pic 4 below) Pic 4 Pic 5 Pic 6 4.
User Manual 8. Display mode: You can convert normal display into full-screen display by clicking the screen on the mobile phone (displayed as Pic 9) When accessing from a mobile phone with Symbian operating system, use the following procedure: 1. First you need to copy the file with suffix “QQeye.CAB” that is included on the CD disk to the mobile phone.
User Manual 5. Once the installation is complete the window in Pic 9 will be displayed to tell you that installation is completed. Then you can go to the Applications folder and select the QQEye program (white box in Pic 10) and click on the Open option (red box in Pic 10) to display the settings menu. After you complete the settings and click on the Done button (red box in Pic 11) the Video window in Pic 12 will be displayed. Open Pic 10 Pic 11 Pic 12 Default Access Point： Input the access point.
User Manual MD AREA: This option allows you select the area you want to be sensitive to motion. The channel is separated into a 13*10 area. When any object moves into the motion detection area, and the area where the object is located is displayed in red recording will be triggered. In the semi-transparent area the motion detection is off. Picture 5-39 5.2.
User Manual 5.2.7.3 Video Setup Click [Main Menu System VIDEO] to setup Video, here you can set Camera system （PAL, NTSC）In the USA we use NTSC. Note: This model does not have a VGA port so VGA resolution does not apply Picture 5-44 5.2.7.4 Language Enter into [System Language] menu to select the language you want to use on the DVR (shown as Picture 5-45) and click [APPLY] button. The selection will be available after system Auto restarts. Picture 5-45 5.2.7.5 Info.
User Manual 5.3 Menu Lock As a system safety feature you can click [Menu Lock] menu to lock menu when leaving the DVR. If you want to login to the DVR, you would input device code and password (refer to the Menu Locking interface- Picture 5-48). Explanation: User only has the authority to search recordings, but Administrator has full authority over Main Menu operations Picture 5-48 5.4 Video Search Click pop-up menu video search to enter into [Video Search] menu you search files and playback recordings.
User Manual 6.2 Log-in to NetViewer Picture 6-1 After webcam installs plug-ins, please select log-in language (Chinese or English) and enter into password and click [Log-in] button, and now you can view DVR remotely through NetViewer. Please note default password is empty. System allows Administrator to set new password as per instructions in section 5.2.6.2 - [Password set] menu. Note: If you want to delete old IE webcam at DVR system update, run the command characters: “regsvr32/u dvrocx.
User Manual 6.3.1.2 Replay This option allows you to playback recordings remotely. First select the day, channel and type and proceed searching and refreshing; second select any event from search result list to playback. Please note you can control playing speed by sliding the playing-control bar on the bottom of the interface (shown as Picture 6-4). Picture 6-4 Play button: [Play]/[Pause] Stop button: stop playing recording. F.F.
User Manual ② Alarm Click [Alarm] menu to enter into its sub menu (shown as Picture 6-7). You can set I/O alarm for every channel, motion detection alarm, motion recording, motion trace, motion sensitivity, video loss alarm, HDD not enough space alarm, HDD not found alarm and alarm output time etc. For details on setup method please refer to section 5.2.5.2. Picture 6-7 System allows you setup motion detection settings for each channel of DVR remotely (shown as Picture 6-8) Picture 6-8 ③ PTZ Control .
User Manual ⑤ Setting Click [setting] menu to enter into the menu interface (shown as Picture 6-11); Click […] button to preview net-viewer recording saving path and screen capture saving path. The menu also allows you to set a lower bandwidth for Internet video transmission, set user password, turn daylight saving time on/off, etc. Picture 6-11 ⑥ Host Info Click [Host Info.] to enter into the sub menu (shown as Picture 6-12).
User Manual Chapter 7: Specification Model D9004 Video System D9008 NTSC / PAL(Optional) Compression Format Video：H.
User Manual Chapter 8: Appendix 8.1 Operation Function Table Type Title Time setting Language Select CH Setting Principle Setting Setting Network Setting Network Function Auxiliary function Menu button Page Setting system date, time and format and day-light saving time setting 21 Setting system language 22 Setting CH title and position; adjusting image color parameter value; setting CH display to 11 ON / Off and time display/recording time overlaying to On/Off. Rec.
User Manual 8.2 Recording Alarm setting Please refer the below matrix: “⊥” stand for “only alarm but no recording”; “AMR” stand for “alarm recording”; “NLR” stand for “normal recording”; and “NOR” stand for “ no recording”. Once alarm is triggered, alarm icon will occur, and when many alarms are triggered, alarm remarks will occur on the screen.
User Manual 8.4 4 Channel System Connections (diagram is for reference only to show where to attach various devices to the DVR, the cameras, external alarms, USB flash drives, monitors and computers are not included with the standard DVR package) 8.
User Manual 8.
User Manual Q-See Product Warranty Thank you for choosing our products. All of our products users have a conditional free warranty repair service for hardware within 12 months starting from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software. Liability Exclusions: Any product malfunction, abnormalities in operation or damage caused by following reasons are not within the free service scope of our company.
User Manual Customer Information Card User’s Name Mr./Mrs. Company Name Postal Address Postal code Phone Number E-mail Model Number of Product Serial Number of Product Purchase Date Distributor The material in this document is the intellectual property of our company. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our company’s prior written permission. 1.
