QSDT8DP DVR User’s Manual QSDT8DP DVR User’s Manual For H.
QSDT8DP User’s Manual CAUTION Please read this user manual carefully to ensure that you can use the device correctly and safely The contents of this manual are subject to change without notice This device should be operated only with the power source supplied with the unit. The power supply voltage must be verified before using.
QSDT8DP DVR User’s Manual CONTENTS CHAPTER 1 Introduction ..................................................................................... 1 1.1 DVR Introduction ............................................................................................ 1 1.2 Main Features ................................................................................................ 1 1.3 DVR Introduction ............................................................................................ 1 1.
QSDT8DP User’s Manual CHAPTER 6 Remote Surveillance ................................................................... 46 6.1 Accessing the DVR ...................................................................................... 46 6.1.1 On LAN....................................................................................................................... 46 6.1.2 On WAN ..................................................................................................................... 47 6.
QSDT8DP DVR User’s Manual CHAPTER 1 Introduction 1.1 DVR Introduction This DVR uses high performance video processing chips and an embedded Linux system. It utilizes many advanced technologies, such as standard H.264 with low bit rate, Dual Stream, SATA interface, VGA output, supports access by mouse, IE browser supported with full remote control, mobile viewing by cell phones, etc. it has very powerful functions and high stability.
QSDT8DP DVR User’s Manual 1.4 Main Features COMPRESSION FORMAT • Standard H.264 compression with low bit rate. Backup file can be played by normal player, without any software or codec installed.
QSDT8DP DVR User’s Manual and RANGE • Supports various PTZ presets and 16 auto cruise tracks • Supports remote PTZ control through internet SECURITY • Two level user group management: advance and normal, rights authorized by administrator • Support one administrator and 15 users.
QSDT8DP DVR User’s Manual CHAPTER 2 Hardware Installation Note: Check the unit and the accessories before using the DVR. Please disconnect the power before connecting to other devices. Don't hot plug in/out 2.1 Installing Hard Drive Note: 1. Supports two SATA hard drives. 2. Please calculate HDD capacity needed according to the recording setting. Please refer to “Appendix B Calculate Recording Capacity”. STEP1 Unscrew and open the top cover STEP2 Connect the power and data cables.
QSDT8DP DVR User’s Manual 2.2 Front Panel Layout Fig 2.6 Front Panel Item Name 1 REC/Focus 2 Search/Zoom 3 Play/Iris 4 REW/Speed 5 FF/PTZ 6 STOP/ESC 7 8 9 Digital buttons IR Receiver Enter button 10 Direction/Multi-screen button 11 Indicator 12 Info/10+ 13 +/Menu button 14 -/Backup Description 1. Record manually 2. FOCUS function enables at PTZ. mode 1. Enter search mode 2. ZOOM function enables at PTZ mode 1. Enter play menu 2. IRIS function enables at PTZ mode 1. Rewind 2.
QSDT8DP DVR User’s Manual 2.3 Rear Panel Layout Fig 2.7 Rear Panel Item Name 1 SPOT OUT 2 3 4 5 6 7 8 9 10 11 12 13 14 AUDIO IN AUDIO OUT USB MOUSE port LAN ALARM IN RS485 POWER INPUT FAN VIDEO OUT VIDEO IN VGA port ALARM OUT +5V and GND Description Connect to monitor as an AUX output channel for one channel. only displays video, not menu 4-channels audio input Audio output, connect to speakers Only for USB mouse Connect to internet Connect to external sensor 1-8.
QSDT8DP DVR User’s Manual Fig 2.8 Sensor Connection Alarm output: The DVR has 1 channel relay alarm output, which just gives on/off signal to external alarm. The status of these pin are illustrated as 8. After alarm Before alarm N. O. COM N. C. N. O . COM N. C. Fig 2.9 Relay Output Status Users need connect their alarm according to the NO or NC type of the alarm. One connection example is shown as Fig 2.9 Fig 2.
QSDT8DP DVR User’s Manual 2.4 Remote Control The remote control uses two AAA batteries, instructions for loading: STEP1 Open the battery cover of the Remote Control STEP2 Insert batteries with the poles (+ and -) correctly aligned STEP3 Replace the battery cover Note: If remote does not function check the following: 1. Check polarity of batteries 2. Check the remaining charge in the batteries 3.
QSDT8DP DVR User’s Manual 2.5 Controlling with a Mouse 2.5.1 Connecting Mouse DVR supports USB mouse through the ports on the rear panel, please refer to Fig 2.10 Remote Control Note: If mouse is not detected or doesn't work, check below: 1. Unplug/re-plug several times 2. Power off/on several times 3. Try another mouse 2.5.2 Using Mouse In live view: Click left mouse button on one camera to display full screen. Click again to return to the previous screen display.
QSDT8DP DVR User’s Manual CHAPTER 3 Basic Function Instructions 3.1 Power On/Off Note: Before you power on the unit, please make sure all the connections are good. Connect the power, the system will show the screen in Fig 3.1 System Loading Fig 3.1 System Loading After that it will enter live in 16 screen mode. The meaning of letters or symbols on screen are shown in the table below. Fig 3.
QSDT8DP DVR User’s Manual To power off safely follow the steps below. Users can close the unit by remote control, front panel and mouse. By remote control: STEP1 Press POWER button, the screen below will appear: Fig 3.3 Shut down STEP2 Choose OK. The unit will power off automatically after shutting down software. STEP3 Disconnect the power By front panel or mouse: STEP1 Press ENTER button or click right mouse to show menu bar, refer to Fig 4.1 Control Bar. STEP2 Click Shut down button, refer to Fig 3.
QSDT8DP DVR User’s Manual Fig 3.4 Login Note: The default password is admin and 123456. Change password: Every user can change his own password. STEP1 While logged in, click Log in/out on the control bar. A window will appear with two options. One is for logout, another for password modification. Click Password, the window will appear as in Fig 3.5 Change Password. STEP2 STEP3 Fig 3.5 Change Password Input the old password. Then input new password 2 times. Press OK button to change.
QSDT8DP DVR User’s Manual Press right mouse button to show the control bar. Enter Menu---->System. STEP1 Enter USER configuration. Click Add button, see Fig 3.6 Add User. Fig 3.6 Add User STEP2 Input user name and password. Choose the user group. STEP3 Click OK button to add a new user STEP4 Choose a user, a symbol will display at the end of the user information. Click Authority button to change the group level. STEP5 Press Delete button to delete the user. A security window will appear as shown below.
QSDT8DP DVR User’s Manual 3.3 Recording 3.3.1 Record Setup Users need to install and format a HDD, and set all the recording parameters before recording. Note: Some vendors sell the DVR with a hard drive already installed, if this is the case you just need to set the recording parameters. There are four recording modes. Users can enable them simultaneously, but only one recording mode works at a time.
QSDT8DP DVR User’s Manual 3.3.2 Manual Recording Just press REC button on the front panel after quitting system setup. Press Stop button to stop recording. Or press REC button on remote control, click again to stop. Or click REC button on the control bar with mouse, click again to stop. 3.3.3 Scheduled Recording Users can set different schedule times for every day of the week. If you want a special schedule for one day, you can use the Holiday function. STEP1 Enter SCHEDULE configuration.
QSDT8DP DVR User’s Manual 3.3.4 Motion Detection Recording This unit supports recording channels and PTZ linking. This means it will record any cameras, or trigger any speed dome to preset or do auto cruise once motion is detected on the camera’s channel. STEP1 Enter MOTION configuration, see Fig 3.10 Motion Detection Setup. Select cameras Fig 3.10 Motion Detection Setup STEP2 Enable Detection first. Enter Area to set Sensitivity and detection Area.
QSDT8DP DVR User’s Manual STEP4 Select alarm out and recording channels. It can trigger any alarm out and cameras to record once motion is detected. STEP5 Enable or disable Buzzer on board. Select speed dome (PTZ) and enable preset or auto cruise. Press OK to save STEP6 Set Hold time. It is the interval time between two consecutive motion events. If a second motion event is detected during the Hold time, it is recognized as a continuation of the first motion event.
QSDT8DP DVR User’s Manual 3.4 Playback This unit supports time search and event search. It displays full or 4 screens in playback. Click right mouse button to show the control bar, refer to Fig 4.1 Control Bar. Click Search, the window below will appear on the screen. Fig 3.14 Search Menu Time search: STEP1 Enter Search configuration, select Time search. A window will appear as Fig 3.15 Calendar Search. If there are recordings during a day, the date will be highlighted. STEP2 Fig 3.
QSDT8DP DVR User’s Manual STEP3 This unit has full and 4 screen playback. Select the screen display mode (the boxes under the channels) and the channels. STEP4 If want to change the date, press Date button. Set hour and minutes of start time. If there is a recording at that time, the boxes will show green. STEP5 Click Play button. It will play from the time point you set.
QSDT8DP DVR User’s Manual STEP3 STEP4 Fig 3.18 Event Search Choose camera and event type, motion or sensor. Double click one video file to play. 3.5 Backup & View STEP1 This unit supports backup to USB Flash through the USB port on the front panel. Users can also make backup to PC by IE browser via internet, refer to 6.3.1 STEP2Select the date, channel and event type. Then click Search. All the files found will be listed in left area. STEP2 Select a file, and click Play button to do remote playback.
QSDT8DP DVR User’s Manual Fig 3.19 Backup Setup STEP4 Choose the camera. And set the start and end time. Click Date button to change the date. STEP5 Click the Backup button. A window will appear as shown in Fig 3.20 Backup Information. Fig 3.20 Backup Information STEP6 Press OK button.
QSDT8DP DVR User’s Manual STEP7 It will show “Backup complete” after finished, as shown below: Check & View: Users can view the backup with third party software like Real Player or Windows Media Player directly. Users can also view with the special software attached with the files during backup. Below are the steps to view the backup with the special software. STEP1 Move the backup device to a computer. Enter the backup folder and open the viewer. Fig 3.
QSDT8DP DVR User’s Manual STEP2 Click Browse to choose the folder which contains the video backup, as in Fig 3.22 Choose Backup Folder. Fig 3.22 Choose Backup Folder STEP3 Set the date and channels. It will show the recorded video in area③ with green at the top as in Fig 3.23 Backup Data Search. Fig 3.23 Backup Data Search If using event search, it will list event files at the bottom of area① STEP4 Drag the slide bar to the start time point, click play button to view. It supports multi screen display.
QSDT8DP DVR User’s Manual Fig 3.24 Play Backup Files Index Definition Play ① ⑤ Forward/Rewi nd Index Index ② Definition Pause Index ③ Definition Stop ⑥ Record ⑦ Volume ⑧ ④ Definition Snap only in pause. Refer to Fig 6.3 Screen mode Tab 3.2 Backup View Control STEP5 Program supports AVI converter. Click “Change File to AVI”. The converter will appear. STEP6 Click Browse to choose the folder which contains the video backup.
QSDT8DP DVR User’s Manual Fig 3.25 AVI Converter STEP8 Select the files. Click Change button, it will start converting the files and show the progress at the bottom. STEP9 When the progress bar shows 100% it is finished. Users can play the AVI files with a third party player directly. STEP10 For more information about network backup, please refer to 6.3.1 STEP2Select the date, channel and event type. Then click Search. All the files found will be listed in left area.
QSDT8DP DVR User’s Manual 3.6 PTZ Control Please connect speed domes to the DVR via RS485 first, refer to 2.3.1 Rear Panel. Make sure the speed dome has a protocol this DVR supports and set the parameters according to its manual. STEP1 Press right mouse button to show the control bar. Enter Menu---->System--->P.T.Z, see Fig 3.26. Fig 3.26 PTZ Setup STEP2 Set protocol, baud rate, and address according to the parameters of the speed dome. STEP3 Click Set button at right of Preset.
QSDT8DP DVR User’s Manual Fig 3.28 Set Cruise STEP5 Select a preset in left preset list, click – button to delete the preset. Click ↑,↓,↑,↓ to adjust the sequence of the presets in the auto cruise setup. Click Save to save and return to the previous interface. STEP6 Click OK button to save and exit. Press right mouse button to show the control bar. Click PTZ to enter PTZ control, shown as Fig 3.29 PTZ Control. Fig 3.29 PTZ Control STEP7 Select the speed dome.
QSDT8DP DVR User’s Manual CHAPTER 4 Menu Setup Guide 4.
QSDT8DP DVR User’s Manual 4.2 Main Menu Setup Click right mouse button, or press ENTER button on the front panel, the control bar will show on the bottom of the screen as in Fig 4.1 Control Bar. Fig 4.1 Control Bar Move the cursor to Menu and click, the pop up menu will show as Fig 4.2 Pop up Menu Fig 4.2 Pop up Menu Select System. A graphic user interface will show as Fig 4.3 System Setup. Fig 4.3 System Setup Press MENU button on the front panel or remote control. The interface above will appear.
QSDT8DP DVR User’s Manual 4.2.1 Basic Configuration Click BASIC to enter basic configuration shown as Fig 4.4 Basic . Fig 4.4 Basic Configuration Here users can set video system, menu language, audio, time and authorization check. The following are the definitions of each option. Device name: The name of the unit. It may display on the client end or CMS, which helps users to recognize the unit remotely. Device ID: It is used to identify multiple devices at the same place.
QSDT8DP DVR User’s Manual 4.2.2 Live Configuration Click LIVE to enter live configuration shown as Fig 4.5 Live Configuration Fig 4.5 Live Configuration Here users can set name/time display, picture color and hide cameras. The following are the definitions of each option. Camera name: Set camera name. It can be a combination of numbers, letters and symbols. Show name: Display camera name in live view. Hide: Hide the picture in live. Unauthorized users cannot view the camera.
QSDT8DP DVR User’s Manual 4.2.3 Record Configuration Click RECORD to enter record configuration shown as Fig 4.7 Record Configuration. Fig 4.7 Record Configuration Here users can set record quality, frame rate, resolution and recycle. The following are the definitions of each option. Video quality: There are 5 options from lowest to highest. The higher the value is, the clearer the recorded picture is. Frame rate: Set recording frame rate. Audio: Enable audio recording.
QSDT8DP DVR User’s Manual 4.2.4 Schedule Configuration Click SCHEDULE to enter schedule configuration shown as Fig 4.8 Schedule Configuration. Fig 4.8 Schedule Configuration Here users can set schedule for timed recording, motion detection and sensor alarm respectively. The following are the definitions of each option: Always, Motion and Sensor: refer to record schedule, motion schedule and alarm schedule respectively. The first column shows the 7 days of the week from Sunday to Saturday.
QSDT8DP DVR User’s Manual Here users can set sensor type, alarm trigger and alarm time. The following are the definitions of each option. Device type: NC and NO (Normal Close and Normal Open). Set the value according to the alarm signal level of the sensors. Enable: Enable sensor alarm. Trigger: Set alarm output, recording channel and speed dome linking. Click Set button, a window will appear shown as Fig 4.10 Alarm Out Configuration. Fig 4.
QSDT8DP DVR User’s Manual 4.2.6 Motion Configuration Click MOTION to enter motion configuration shown as Fig 4.11 Motion Configuration. Fig 4.11 Motion Configuration Here users can set motion sensitivity, detection area and alarm out. The following are the definitions of each option: Enable: Enable motion detection. Trigger: Setup similar with that of sensor alarm, but linked speed domes need to use different channels, i.e.
QSDT8DP DVR User’s Manual 4.2.7 Network Configuration Click NETWORK to enter network configuration as shown in Fig 4.13 Network Configuration. Fig 4.13 Network Configuration This unit supports DHCP, PPPoE, DDNS. Users enable network function, and configure IP address, DDNS, transmission video parameters here. The following are the definitions of each option: HTTP port: The default is 80. If users change the value, they need add the port number when typing the IP address in IE address blank, i.e.
QSDT8DP DVR User’s Manual DDNS: Click DDNS, a window will appear as shown in Fig 4.14 DDNS Configuration. DVR supports DYNDNS and MYQ-SEE. Users need register at www.dyndns.com or myq-see.com. Then input registered ID and password here. Click OK button. The unit will connect Through DYNDNS or MYQ-SEE. Fig 4.14 DDNS Configuration Server: Select DDNS server. User name and Password: Input registered information from DDNS provider. This unit supports dual stream.
QSDT8DP DVR User’s Manual 4.2.8 P.T.Z Configuration Click P.T.Z to enter PTZ configuration shown as Fig 4.16 PTZ Configuration. Fig 4.16 PTZ Configuration Here users can set protocol, baud rate, address, presets and auto cruise track. The following are the definitions of each option: Protocol, Baud rate, Address: Set the value according to the settings of the speed dome. Speed: Set the speed of the speed dome. Preset, Name: Select a preset and name it. Click Set, a window will appear shown as Fig 4.17.
QSDT8DP DVR User’s Manual 4.2.9 User Configuration Click USER to enter user management interface shown as Fig 4.18 User Configuration. Fig 4.18 User Configuration Administrator can add, delete users, and change their authorization.. . Note: DVR supports one administrator and maximum of 15 users. 4.2.10 Tools Configuration Click TOOLS to enter tools configuration shown as Fig 4.19 Tools Manager. Fig 4.19 Tools Manager Disk manager: Please refer to 5.1 Formatting the Hard Disk. Update: Please refer to 5.
QSDT8DP DVR User’s Manual CHAPTER 5 Managing the DVR 5.1 Formatting the Hard Disk If you want to record, it is necessary to format the hard disk at first. If not being formatted, it will show the position of the disk, free space and total space show 0M at the bottom of screen. STEP1 Enter USER configuration, referring to 4.2.10 Tools Configuration. Press Disk manager, a window will pop up as Fig 5.1 Disk Manager. Fig 5.1 Disk Manager STEP2 If a disk has never been formatted, Status will show “new”.
QSDT8DP DVR User’s Manual STEP5 After finishing, the unit needs to be restarted. Note: If a “no device or no file” error appears, it is possible that the USB device is incompatible. Please try a different USB flash drive. Please be patient. It will take 2-3 minutes to update. 5.3 Load Default Setup The DVR has different setup blocks, like Basic, Record, Schedule, Motion etc. Users can choose any block to do default, as shown in Fig 5.2 Reset Blocks. Fig 5.
QSDT8DP DVR User’s Manual Fig 5.3 Status Interface STEP3 Click System, the window below will display. Check firmware version, recording parameters here. Fig 5.4 System Information. STEP4 Return to the previous menu, click Network. The window below will display. Check IP address, DVR Mac address, network video quality. Fig 5.5 Network Information.
QSDT8DP DVR User’s Manual 5.5 Check System Log This unit logs system events. It records its working state and operation automatically, and it divides the record to two groups, events and operation. The form below is the details of the two groups. Group Events Operation Details Motion, Video Loss, Alarm Delete File, Lock File, Search, Login, Enable check, Boot, Shutdown, Reset, Start Record, Stop Record, Setup Basic, Setup Live, Setup Record, Setup Schedule, Setup Alarm, Setup Network, Setup P.T.Z Tab 5.
QSDT8DP DVR User’s Manual STEP5 Fig 5.7 Operation Log The operation is similar to searching events log. Note: The log files are saved to the HDD inside. If HDD is not installed, it won’t record any thing. The number of log files is unlimited. 5.6 Check On-line Network Users Press right mouse button to show the control bar. Click Menu---->Online users. It will show the details of the current connections as shown below: Fig 5.
QSDT8DP DVR User’s Manual 5.7 Lock & Delete Files Users can control every video file, locking and deleting them. Once users lock an important file, it cannot be covered or deleted. But the locked files can still be cleared by formatting. STEP1 Press right mouse button to show the control bar. Click Menu, refer to Fig 4.2 Pop up Menu. STEP2 Click Search----->File manager, the window below will appear. Fig 5.9 File Manager STEP3 Click Date to change date by a calendar, click Search to refresh the list.
QSDT8DP DVR User’s Manual CHAPTER 6 Remote Surveillance 6.1 Accessing the DVR If you want to view the DVR remotely it must be connect to a LAN or internet, and network server must be enabled in the unit. Please refer to 4.2.7 Network Configuration. This unit supports Internet Explorer browser without any client software installed, it supports XP and Vista operating systems. 6.1.1 On LAN STEP1 Input IP address, Subnet, Gateway. If using DHCP, please enable DHCP in both the DVR and router.
QSDT8DP DVR User’s Manual 6.1.2 On WAN There are two ways that the DVR can be connected to the internet. 1. Connect the DVR to internet through a router or virtual server. STEP1 Input IP address, Subnet, Gateway. You can get the Subnet and Gateway by going to the run option on a computer that is attached to the same router as the DVR and typing “cmd” or in the run box and clicking ok. This will open a dialog box. At the command prompt type “ipconfig”.
QSDT8DP DVR User’s Manual 6.2 Remote Viewing When you enter remote preview you will see the interface shown below: Fig 6.2 Remote Preview Interface ① Full screen, 4/8 screens display mode. ② Camera status: There are four rows of indicators, which refer to recording, video loss, motion and alarm respectively. When the indicator displays red, it means the relative event. If it shows grey, means the relative event doesn't exist.
QSDT8DP DVR User’s Manual ④, ⑤ and ⑥ are the function blocks. When one is active, the button will show orange. Snap pictures: STEP1 Click on a channel to choose. Click the button, a window will appear as in Fig 6.3 Preview Snap. Fig 6.3 Preview Snap STEP2 Select frames captured one time. Enable Title and Time, it will capture title and time simultaneously. STEP3 Click Snap to capture pictures. STEP4 Click Browse to set saving path.
QSDT8DP DVR User’s Manual PTZ control: Click P.T.Z to enter the interface shown below. Click on a channel to select the speed dome. Fig 6.4 Remote PTZ control ① Move the speed dome. ② Stop adjustment. ③ Adjust zoom, focus, Iris, Speed. ④ Go to the preset. Click to rename the preset. ⑤ Select and do auto cruise. Click right mouse, a pull-down menu will appear as shown below. Fig 6.5 Preview Control Menu Audio: Enable remote audio transmission. Users can hear the audio from the DVR.
QSDT8DP DVR User’s Manual Fig 6.6 Set Cruise Double click Add to add presets for the selected cruise. Click the preset, a down list menu will pop up. Users can select presets to add. Double click Time to set display time in auto cruise. Click Delete or Clear all to delete the presets. Click OK to save and exit. Fast stream: Enable the master stream. This DVR supports dual stream, sub stream and master stream. Sub stream has low frame rate, max 3fps for every channel, refer to 4.2.7 Network Configuration.
QSDT8DP DVR User’s Manual 6.3 Remote Playback &Backup 6.3.1 Remote Playback Click Search to enter the playback and backup block as below, where users can make remote playback, remote backup and remote video file management. Fig 6.7Remote Playback &Backup Interface This DVR supports remote time search, event search and one channel playback. The above is the default interface after entering Playback &Backup block.
QSDT8DP DVR User’s Manual Fig 6.8 Remote Playback STEP5 Users can select fast forward/backward, pause, stop playback and snap pictures. About snap feature, it is the same as in remote preview; refer to Fig 6.3 Preview Snap. Click to return to search interface. By event search: STEP1 Click Event search, the window below will display: Fig 6.
QSDT8DP DVR User’s Manual STEP2 Select the date, channel and event type. Then click Search. All the files found will be listed in left area. STEP3 Select a file, and click Play button to do remote playback. The following steps are the same as STEP5-6 of time search above. 6.3.2 Remote Backup Users can download the recorded files from the DVR through a network. Click Backup to enter the interface shown below: Fig 6.10 Remote Backup Interface STEP1 Select the date and channel. Then click Search button.
QSDT8DP DVR User’s Manual 6.4 Remote Menu Configuration Except network parameters, users can set all the parameters like resolution and schedule remotely through network, not going to the DVR. Click Setup to enter the interface as below: Fig 6.11 Remote Menu Setup The sub menu lists, and the options in every sub menu are similar with those on the DVR. Please refer to 4.2 Main Menu Setup to do setup. Click Save to save the changes. Some changes may pop up a dialog box as below and need a restart.
QSDT8DP DVR User’s Manual 6.5 Remote DVR Management 6.5.1 Check System Log Remotely Users can check system log remotely. For the details of system log, please refer to Tab 5.1 Details of System Log. STEP1 Click Search---->Log, the window below will appear. Event log search is the default interface. STEP2 STEP3 STEP4 Fig 6.12 Remote System LOG Search Select the date, channel and event type. Then click Search. The entire log found will be listed in left area.
QSDT8DP DVR User’s Manual STEP5 Select the date and click Search. It will list all the log files in the day in left area. 6.5.2 Lock & Delete Files Remotely Users can lock and delete video files through network. STEP1 Click Search---->Playback---->File manager, the window below will appear: Fig 6.14 Remote File manager STEP2 Select the date and channels, click Search. All the files found will be listed in the day in left area. STEP3 The relative status will show “Lock” if the file is locked.
QSDT8DP DVR User’s Manual CHAPTER 7 Mobile Surveillance This DVR supports mobile surveillance by PDA or smart phones with WinCE and Symbian OS. It also supports 3G network. We tested Dopod D600 (WM5) and Dopod S1(WM6), which work fine with the DVR. To use mobile surveillance, you first need to enable network service on the DVR, refer to 4.2.7 Network Configuration. Below are the instructions for use on the mobile client end for the two operating systems.
QSDT8DP DVR User’s Manual STEP4 Click “Yes” to download and install. STEP5 PCam will be opened after installed. STEP6 Input the server’s address, ID, and password respectively in the columns of “Server”, “User”, and “Password”. Then click “Go” to login to the DVR. It will show the picture if accessed successfully.
QSDT8DP DVR User’s Manual STEP7 Camera 1 is the default display after login. Change the camera in the drop down menu of “Channel”. Notice: User name and password here are the same as that used on the DVR. The defaults are user name “admin” and password “123456”. 7.2 Accessing From Phones with Symbian Please use the smart phones with Symbian version supported by this unit. STEP1 First enable the network access on the mobile phone. And then run Web browser.
QSDT8DP DVR User’s Manual STEP4 The security windows will pop up after downloading and ask if OK to install the package. Click YES to install. STEP5 A Scam shortcut icon appears on the system menu after finish. STEP6 Run Scam program. STEP7 Click Options--->Settings to enter login interface.
QSDT8DP DVR User’s Manual STEP8 Input the server’s address, ID and password respectively. And click OK to login the DVR. STEP9 Screen will show the camera after accessing successfully. Note: User name and password here are the same with that used on the DVR. The defaults are admin and 123456. 7.3 Accessing From iPhones At present, the software only supports iPhone os2.2 and above, if phone firmware is lower than this version please upgrade it.
QSDT8DP DVR User’s Manual Step 2: Enable “search” function to search for “SuperCam”, the available programs will be displayed on the top of search box Step 3: Click SuperCam, enter into “introduce” interface and click FREE”, it will change into “INSTALL” Step 4: Enter into iTunes Store password, click “OK” the below interface will display. Note: if this is the first time the user is using this feature you will need to enter user ID; if there is no Store account, user need to apply for one.
QSDT8DP DVR User’s Manual Step 5: Download and install. After installed, SuperCam icon will display. Click this icon, a function interface will appear as shown below. Step 6: Click “System setting”, to enter into login interface. Enter server’s IP address (or domain name), user’s ID and password. Click Back to save.
QSDT8DP DVR User’s Manual Step 7: Click Live View, the default Cam1 picture will be displayed. Click to capture picture. Click to enter PTZ mode. Step 8: On function interface, click Image View to view the captured picture. or to switch to next or previous picture. Click Click current picture.
QSDT8DP DVR User’s Manual Live View After successfully installing SuperCam software, Click on System Setting (Pic 1), and then enter Server IP address or Domain, User name and password to log in (Pic 2). If you connect successfully, it will go to Live View of CH1 as default (Pic 3), You can choose other desired channels from channel button underneath. Other functions are: 1. : switch channels 2. : picture snap. 3.
QSDT8DP DVR User’s Manual Appendix A FAQs Q1. The DVR does not start after connecting the power, what is wrong? a. The power adapter may have been damaged, or is not providing enough power. Please change the adapter b. The DVR may not be getting enough power from the outlet or surge protector it is attached to. c. There could be a problem with the system board on the DVR Q2. The indicator lights of the DVR are on, but no output. Why? a.
QSDT8DP DVR User’s Manual Q6. I can not use the mouse, what could be the problem? a. Wait 5 minutes after mouse connected and then try. b. Mouse is not securely connected. Plug/unplug several times. c. The mouse is incompatible with the system. Please try another mouse. Q7. My computer will not download ActiveX control for remote viewing, what can I do? a. IE browser may be blocking ActiveX controls. Try the following steps: ① Open IE browser. Click Tools-----Internet Options….
QSDT8DP DVR User’s Manual ③ Enable all the sub options under “ActiveX controls and plug-ins” ④ Then click ok to finish setup. b. Other plug-ins or anti-virus programs may be blocking ActiveX. Please uninstall or close them NOTE: On many systems you many have another option. You can go into internet options in Internet Explorer, enter the IP address you use to access the DVR as a trusted site, then go to the default level button and set move the bar down to the low setting, click apply and ok.
QSDT8DP DVR User’s Manual drive. Solution: Try reformatting the current drive or re-placing it. Q9: Why isn’t the mouse I have plugged into the front USB port working? The front USB port is only for backup to USB flash drive, and does not support a USB mouse. Please use the USB port on the rear panel if using a mouse.
QSDT8DP DVR User’s Manual Appendix B Calculating Recording Capacity Users can calculate the size of hard drive needed based on DVR recording settings. The DVR uses fixed video bit rate. Below is the space used at different settings. Video Format PAL Resolution CIF NTSC CIF Frame Rate Total (FPS) 25 30 Video Quality Bit Rate (kbps) Storage Used (MB/h) Highest 640 281 Higher 512 225 Medium 384 168.7 Lower 256 112.
QSDT8DP DVR User’s Manual Appendix C Compatible Devices 1. Compatible USB drives (that we have tested): Brand Capacity SSK 512MB, 1G, 2GB Netac 4GB Kingston 2GB Aigo 2GB Smatter vider 1GB Sandisk 4GB Tab C.
QSDT8DP DVR User’s Manual Appendix D DVR Specifications Compression format Standard H.264 Baseline Video output Composite：1.0V p-p/75Ω，BNC×2 VGAX1 Video input Composite：1.
QSDT8DP DVR User’s Manual Q-SEE Product Warranty Thank you for choosing our products. All of our products users have a conditional free warranty repair service for hardware within 12 months starting from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software.
QSDT8DP DVR User’s Manual Customer Information Card User’s Name Mr./Mr s.
QSDT8DP DVR User’s Manual DISCLAIMER: The material in this document is the intellectual property of our company. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our company’s prior written permission. 1. Our products are under continual improvement and we reserve the right to make changes without notice. But no guarantee is given as to the correctness of its contents. 2.
