Fingerprint PLUS Keypad & Deadbolt Lock TRADEMARKS All brand names and products are Registered Trademarks of their respective Companies. LEGAL DISCLAIMER See warning on rear cover. DISCLAIMER The information in the document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of selling or functionality for any particular purpose. Digital Peripheral Solutions Inc.
CONTENTS 1. Introduction 1 1.1 Features 1 1.1.1 Model number 1 1.1.2 Main features 1 1.2 Size & Weight 2 1.2.1 Lock size 2 1.2.2 Mortise size 3 1.2.3 Weight 3 1.3 Technical Parameters 4 1.3.1 Technical Parameters 4 1.3.2 Operating Environment 5 1.4 Components 5 1.5 Structure View 6 2. Operation Instruction 7 2.1 Left handed and Right handed 7 2.2 Status of the lock 7 2.3 Instruction for indicators 8 2.4 Function of buttons 8 2.5 Master fingerprint & Emergency PIN 9 2.5.
QSE7F4 USER MANUAL 2.6.2 How to erase group member fingerprint? 2.7 Unlocking 15 1. Introduction 15 2.7.1 Unlock with Emergency PIN 15 2.7.2 Unlock with group member fingerprint 16 2.7.3 Unlock with mechanical key 17 2.8 How to set the status of the lock? 17 1.1 Features 1.1.1Model number Fingerprint Plus Keypad & Deadbolt Lock 2.8.1 Lock status 17 2.8.2 Lock-out status 17 2.8.3 Normally open status 2.9 Change batteries 3. Installation 18 19 20 3.1 Door requirement 20 3.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 8. Blue background light, convenient for night use. 1.2.2 Mortise size Unit 9. “Normally open” status can be set for meetings or events. mm 10. Operates on 4 AA alkaline batteries or a 9V battery, with low voltage alert. 11.Auto alarm function: If the door is not locked properly, the latches draw out , 3 seconds later the lock will alarm automatically.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 1 . 3 . 2 Operating Environment 1.3 Technical Parameters 1.3.1 Technical Parameters No: Outdoor Temperature -8 -50 Indoor Temperature -5 -50 Technical parameters Item Humidity Fingerprint sensor Optical sensor,CMOS 0.3 Mega Pixel Sensor resolution 500 dpi Antistrike ability of sensor surface Remain good condition after being jabbed with a 4H pencil at a 20cm's distance. Authentication speed Authentication methods 1.4 Components 1:N FRR 1% FAR 0.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 1. Operation Instruction Cylinder cover 2.1 Left handed and Right handed Front plate 1.5 Structure view Right handed Mortise Left handed 1.Standing out of the door, if the hinge is on the left, it is left handed lock. 6 Plastic screw cover Fixing screw M5 X L Battery cover Hexagon screw M6 X L Tapping screw M4 X 25 Back plate 2. Standing out of the door, if the hinge is on the right, it is right handed lock . 2.2 Status of the lock 1.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 2.Lock-out status, locked with latches and deadbolt,(Figure 2-2) Button “1” - TO ENROLL GROUP MEMBER'S FINGERPRINT(S) Button “2” - TO ERASE GROUP MEMBER'S FINGERPRINT(S) Button “3”- TO SET THE LOCK INTO NORMALLY OPEN STATUS 2.5 Master fingerprint & Emergency PIN 2.5.1 How to set Master fingerprint? 1.Press and hold the cylinder cover button, slide down the cylinder cover with another hand. (Figure 2-3) 2-2 3.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL long beep, which indicates the successful setup for Emergency PIN. 5.After setting the Emergency PIN successfully, turn the mechanical key to the original position and draw out, put the cylinder cover back. NOTE: 1.While the lock is waiting for setup, if you don't put the finger or input Emergency PIN, the red light on sensor will go out after 5 seconds' flashing. 2.Master fingerprint and Emergency PIN have to be set separately. 2-5 3.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL Referring to the list, let's take the member in Group A, Fingerprint No. 0001 for example. 2.6 Enroll & erase group member's fingerprint(s) Fingerprint number & name list Group A No. Name Fingerprint Name Group C Fingerprint Name Group D Fingerprint Name 1.Place Master finger on the sensor, the lock will be activated once the infrared detector detects the finger.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 2.6.2 How to erase group member fingerprint? 1. The same operation with the steps 1 and 2 in 2.6.1 2. Press button “2”, a long beep is heard, red indicator goes out, green indicator lights .(Figure2-8) 2-7 (NOTE: the green indicator will light for about 4 seconds, step 4 must be done within 4 seconds.) 2-8 4.Input fingerprint number “0001”, a long beep is heard, which indicates the successful first input of this fingerprint number. 5.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL be locked, Master fingerprint or group member fingerprint can cancel the 2.7.3 Unlock with mechanical key locked status, or the locked status will be deleted in 1 minute automatically. 1.The same operation with step 1 in 2.5.1. 2.Blue background and green indicator light up, a long beep is heard, the inside 2.Insert mechanical key into the keyhole, turn the key (anticlockwise if right motor is activated.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL flashes once for a second, which indicates the lock is set into open Normally status successfully. 3.Unlock with Emergency PIN or group member fingerprint again, after you hear the motor activated, the Normally open status is cancelled. 2.9 Change batteries When the low voltage indicator turns on, to ensure the normal use of your lock, 2-11 please change the batteries as soon as you can by following below steps: 1.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 3.Installation 3.3 Installation template Unit mm C 1. Material of door: wood. C B 3.1 Door requirement 20 Drill bit 1pc Hammer 1pc Square ruler 1pc File 1pc Knife 1pc Drill 1pc Screwdriver 1pc Chisel 1pc Pencil 1pc Tape measure 1pc A--A A Socket 1pc Lever centerline Electric drill 1pc A The following tools (not provided) are suitable for installing this lock. QSE7F4 Drilling View of door and door frame C--C 3.2 Tools required B.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 6.Put 4 AA alkaline 3.4 Installation steps batteries in battery box as instructed. 1.Draw lever centerline as your request, the recommended height is 1 meter above the ground. Mark the door for drilling holes with a pencil according to 7 .M a r k t h e d o o r frame for drilling holes as per drilling view. Cut out the cavity for strike and strike plate. Put strike into the cavity, covered with strike plate, fix them on the door frame with 3 pcs of M4*25 screws.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 5. Appendix 4.Maintenance 4.1 Daily maintenance 5.1 Package Contents A. Keep away from corrosive material. B. Do not hang anything on the levers. C. Keep the sensor surface clean and dry. Wipe it with soft and dry cloth if any stain on it. D. When the batteries are dying, the red indicator flashes to alert low voltage.
QSE7F4 USER MANUAL QSE7F4 USER MANUAL 5.3 Fingerprint number & name list 5.2 Handle Orientation Group A No.
